Indicates if the Enhanced Multi-Link Multi-Radio (EMLMR) operation is supported. Indicates if Enhanced Multi-Link Single-Radio (EMLSR) operation is supported. Indicates if Simultaneous Transmit and Receive (STR) operation is supported. Indicates if Non-Simultaneous Transmit and Receive (NSTR) operation is supported. Indicates if Traffic Identifier (TID) to Link Mapping Negotiation is supported. {{numentries}} {{numentries}} {{numentries}} {{numentries}} The Radio unique identifier (RUID) of another radio to which the specified frequency separation gap applies. Frequency separation to the specified radio for the particular MLO operation mode. A value of 0 indicates that no frequency separation information is provided. Set to a nonzero value to indicate the required frequency gap is ({{param}} - 1) x {{units}}. The maximum number of MLDs that the EasyMesh Agent can support. {{bibref|EasyMesh}} source: Wi-Fi 7 Agent Capabilities TLV. The maximum number of affiliated APs supported by any AP MLD on this EasyMesh Agent. Set to a value between 0 and 14, which is the number of affiliated APs minus 1. The value of 15 is reserved. {{bibref|EasyMesh}} source: Wi-Fi 7 Agent Capabilities TLV. The maximum number of affiliated bSTAs supported by the bSTA MLD on this EasyMesh Agent. Set to a value between 0 and 14, which is the number of affiliated bSTAs minus 1. The value of 15 is reserved. {{bibref|EasyMesh}} source: Wi-Fi 7 Agent Capabilities TLV. Indicates the EasyMesh Agent support for TID to Link mapping. {{bibref|EasyMesh}} source: Wi-Fi 7 Agent Capabilities TLV. {{enum}} The EasyMesh Agent does not support TID-to-link mapping. The EasyMesh Agent supports the mapping of each TID to the same or different link set. The EasyMesh Agent only supports the mapping of all TIDs to the same link set. The number of packets transmitted by the affiliated AP. Note: this counter counts only MLD traffic through this BSSID, not legacy (non-MLD) traffic. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. The total number of packets received from the affiliated STAs by this affiliated AP. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. Total number of unicast bytes transmitted to MLD STAs associated with the affiliated AP. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. Total number of unicast bytes received from MLD STAs associated with the affiliated AP. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. The number of packets which could not be transmitted by the affiliated AP due to errors. This counter counts only MLD traffic through this BSSID, not legacy (non-MLD) traffic. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. Total multicast bytes transmitted to MLD STAs associated with the affiliated AP. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. Total multicast bytes received from MLD STAs associated with the affiliated AP. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. Total broadcast bytes transmitted to MLD STAs associated with the affiliated AP. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. Total broadcast bytes received from MLD STAs associated with the affiliated AP. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. Indicates if the Enhanced Multi-Link Multi-Radio (EMLMR) operation is enabled. Indicates if Enhanced Multi-Link Single-Radio (EMLSR) operation is enabled. Indicates if Simultaneous Transmit and Receive (STR) operation is enabled. Indicates if Non-Simultaneous Transmit and Receive (NSTR) operation is enabled. Indicates if Traffic Identifier (TID) to Link Mapping Negotiation is enabled. {{bibref|EasyMesh}} source: TID-to-Link Mapping Policy TLV. The direction of the traffic flow from the perspective of the AP MLD. {{enum}} The traffic identifier (TID) for this mapping. The BSSID of the preferred link (affiliated AP) to use for traffic with matching direction and TID values. {{list}} The Link ID of the preferred link (affiliated AP) to use for traffic with matching direction and TID values. {{numentries}} Table of Multi-Link Operation (MLO) capable Access Points (APs) on this EasyMesh Agent or Single AP device. {{bibref|EasyMesh}} source: Agent AP MLD Configuration TLV. The Multi-Link Device (MLD) MAC Address of the MLO Capable access point (AP). {{bibref|EasyMesh}} Source: Agent AP MLD Configuration TLV. {{param}} is a reference to the APMLDTemplate selected for this {{object}}. {{numentries}} {{numentries}} {{numentries}} This object describes the Wi-Fi 7 Multi-Link Operation (MLO) configuration of the Multi-Link Device (MLD) Access Point (AP), {{bibref|EasyMesh}} source: Agent AP MLD Configuration TLV. {{numentries}} Table of Traffic Identifier (TID) to Operating Class to be used as a policy when configuring TID-to-Link Mapping in the Multi-Link Operation (MLO) capable access point (AP). Each table entry describes the mapping between a particular TID and direction and the required current Operating Class for any link to be used for this TID when constructing a TID-to-Link Map {{bibref|EasyMesh|Section 20.2.8}}. This parameter indicates whether the TID-to-Link mapping entry is enabled for Multi-Link Operation (MLO) on the access point (AP). When set to "true", the mapping between the specified Traffic Identifier (TID), direction, and required Operating Class will be active, and the TID-to-Link mapping policy will be applied during Multi-Link operations. When set to "false", the entry will be ignored. The traffic identifier (TID) for this mapping. This {{param}} is a unique key for this table. {{list}} The Operating class of an available channel, from {{bibref|802.11ax|Table E-4}}. The TID can be mapped to any link using a radio with a current operating class within this list. The direction of the traffic flow from the perspective the AP MLD. {{enum}} This {{param}} is a unique key for this table. Table of Traffic Identifier (TID) to Link Mappings of the Multi-Link Operation (MLO) capable access point (AP). Each table entry describes the mapping between a particular TID and direction and preferred link. {{bibref|EasyMesh}} source: TID-to-Link Mapping Policy TLV. This object describes the relationship between an Affiliated AP and the Operating Class (OpClass) of the Radio that the Affiliated AP is operating on {{bibref|EasyMesh|Section 20.2.8}}. The Link ID assigned to one of the affiliated APs of this AP MLD. {{bibref|EasyMesh|Section 17.2.96, Agent AP MLD Configuration TLV}} One of the current Operating Class per {{bibref|802.11ax|Table E-4}} that the Radio on which the Affiliated AP with the given {{param|LinkID}} is operating on. The Access Points (APs) affiliated to the AP MLD. {{bibref|EasyMesh}} Source: Agent AP MLD Configuration TLV. Counters in this object only include MLD traffic. The BSSID of the affiliated AP. This should be set to one of the values of {{param|##.Radio.{i}.BSS.{i}.BSSID}}. {{bibref|EasyMesh}} source: Agent AP MLD Configuration TLV. The Link ID assigned to this affiliated AP. {{bibref|EasyMesh}} source: Agent AP MLD Configuration TLV. The Radio unique identifier (RUID) of the Radio that this affiliated AP is operating on. {{bibref|EasyMesh}} source: Agent AP MLD Configuration TLV. Disabled Subchannel Bitmap subfield from the EHT Operation element in transmitted Management frames. Null value or not present for stations. {{bibref|EasyMesh}} source: Static Puncturing Configuration TLV. Estimated Service Parameters information field for AC=BE, defined per {{bibref|802.11-2020|Figure 9-637}} and referenced in {{bibref|EasyMesh|Section 17.2.22}}. Estimated Service Parameters information field for AC=BK, defined per {{bibref|802.11-2020|Figure 9-637}} and referenced in {{bibref|EasyMesh|Section 17.2.22}}. Estimated Service Parameters information field for AC=VI, defined per {{bibref|802.11-2020|Figure 9-637}} and referenced in {{bibref|EasyMesh|Section 17.2.22}}. Estimated Service Parameters information field for AC=VO, defined per {{bibref|802.11-2020|Figure 9-637}} and referenced in {{bibref|EasyMesh|Section 17.2.22}}. A bit map indicating each Wi-Fi generation supported by this {{object}} * Bit 0: Wi-Fi HaLow (802.11ah) * Bit 1: Wi-Fi 1 (802.11b) * Bit 2: Wi-Fi 2 (802.11a) * Bit 3: Wi-Fi 3 (802.11g) * Bit 4: Wi-Fi 4 (802.11n) * Bit 5: Wi-Fi 5 (802.11ac) * Bit 6: Wi-Fi 6 (802.11ax) * Bit 7: Wi-Fi 7 (802.11be) * Bit 8: Wi-Fi 8 (802.11bn) Notes: * This list will be expanded in the future as new Wi-Fi generation appears. * Indications are for the device, not the 802.11 STA per se. For example, an 802.11ac device sets the Wi-Fi 5 Supported bit even if it's currently connected on the 2.4GHz band. * Bits are counted from the LSB (bit 0) to the MSB. If the STA includes a Generational Capabilities Indication attribute, as defined in {{bibref|WFA Capabilities|Table 6}} in its (Re)Association Request frames or in its Wi-Fi Alliance Capabilities frames, the information about support for Wi-Fi 4 and above may be retrieved from this attribute. In addition, or alternatively when the STA doesn't include a Generational Capabilities Indication attribute in its (Re)Association Request frames and Wi-Fi Alliance Capabilities frames, the DataElements Agent may use the following guidance to infer STA support of a Wi-Fi generation: * If a STA includes a S1G Capabilities IE in its (Re)Association Request frames, the DataElements Agent indicates support for Wi-Fi HaLow for this STA. * If a STA includes a Supported Rates IE in its (Re)Association Request frames and if either 1, 2, 5.5 or 11 Mbps rate is indicated in this IE, the DataElements Agent indicates support for Wi-Fi 1 (802.11b) for this STA. * If a STA includes a Supported Rates IE in its (Re)Association Request frames and if either 6, 12 or 24 Mbps rate is indicated in this IE when sent on the 5GHz band, the DataElements Agent indicates support for Wi-Fi 2 (802.11a) for this STA. * If a STA includes a Supported Rates IE in its (Re)Association Request frames and if either 6, 12 or 24 Mbps rate is indicated in this IE when sent on the 2.4GHz band, the DataElements Agent indicates support for Wi-Fi 3 (802.11g) for this STA. * If a STA includes a HT Capabilities IE in its (Re)Association Request frames, the DataElements Agent indicates support for Wi-Fi 4 for this STA. * If a STA includes a VHT Capabilities IE in its (Re)Association Request frames, the DataElements Agent indicates support for Wi-Fi 5 for this STA. * If a STA includes a HE Capabilities IE in its (Re)Association Request frames, the DataElements Agent indicates support for Wi-Fi 6 for this STA. * If a STA includes a EHT Capabilities IE in its (Re)Association Request frames, the DataElements Agent indicates support for Wi-Fi 7 for this STA. * If a STA includes a UHR Capabilities IE in its (Re)Association Request frames, the DataElements Agent indicates support for Wi-Fi 8 for this STA. Notes: * In case of a Multi-AP deployment, the DataElements Agent / Multi-AP Controller obtains the body of the (Re)Association Request frames sent by the STA by using either the Tunneled Message mechanism defined in {{bibref|EasyMesh|Section 11.7}} or the Client Capability procedure defined in {{bibref|EasyMesh|Section 9.2}}. * In case of a Multi-AP deployment, the DataElements Agent / Multi-AP Controller obtains the body of the Wi-Fi Alliance Capabilities frames sent by the STA by using the Tunneled Message mechanism defined in {{bibref|EasyMesh|Section 11.7}}. A bit map indicating each WFA Capability supported by this {{object}}, as defined in {{bibref|WFA Capabilities|Table 3}} * Bit 0: QoS Management DSCP Policy * Bit 1: QoS Management Unsolicited DSCP Policy At Association * Bit 2: QoS Management SCS Traffic Description * Bit 3: 5G QoS to Wi-Fi QoS Mapping * Bit 4: DAR Latency Statistics Reporting Support * Bit 5: DAR Radio Counters Statistics Reporting Support * Bit 6: DAR Control Plane Events Reporting Support * Bit 7: DAR Unsolicited Report Reception Support A value of 0 indicates that either the information has not been provided by the STA or that the STA doesn't support any of the capabilities listed in {{bibref|WFA Capabilities|Table 3}}. Notes: * This information is copied from the Capabilities field included in the Wi-Fi Alliance Capabilities Element or Wi-Fi Alliance Capabilities frame, as defined in {{bibref|WFA Capabilities|Table 3}}. * Bits are counted from the LSB (bit 0) to the MSB. The Multi-Link Device (MLD) MAC Address of the MLO Capable bSTA. {{bibref|EasyMesh}} Source: Backhaul STA MLD Configuration TLV. The MLD MAC address of the upstream AP MLD that this bSTA MLD is associated to. {{bibref|EasyMesh}} source: Associated Clients TLV. {{list}} backhaul STA MAC addresses affiliated to this bSTA MLD. {{bibref|EasyMesh}} source: Backhaul STA MLD Configuration TLV. This object represents the Multi-Link Operation (MLO) capable backhaul station (bSTA) operating on this EasyMesh Agent. Only one MLO capable bSTA per EasyMesh Agent is allowed. {{bibref|EasyMesh}} source: Backhaul STA MLD Configuration TLV. This object describes the Multi-Link Operation (MLO) configuration of a Multi-Link Device (MLD) backhaul STA (bSTA). {{bibref|EasyMesh}} source: Backhaul STA MLD Configuration TLV. {{numentries}} Table of Multi-Link Operation (MLO) capable backhaul stations (bSTAs). Each instance groups one or more endpoint SSIDs across different radio bands into a single MLD for IEEE 802.11be Multi-Link Operation (MLO). An instance is created when one or more endpoint SSIDs are configured with the same MLDUnit value. This object describes the Multi-Link Operation (MLO) configuration of a Multi-Link Device (MLD) backhaul STA (bSTA). {{numentries}} This object describes Multi-Link Operation (MLO) capable stations (STAs), also known as client Multilink Devices (MLDs), associated to this MLO capable Access Point. {{bibref|EasyMesh}} source: Associated Clients TLV. The Multi-Link Device (MLD) MAC Address of the STA MLD. {{bibref|EasyMesh}} source: Associated STA MLD Configuration Report TLV. The Hostname for the STA MLD. The IPv4 address allocated to the MLD MAC Address of this device. The IPv6 address allocated to the MLD MAC Address of this device. Indicates if the STA MLD is a backhaul STA MLD (bSTA MLD). This is useful to identify the type of STA MLD when the same AP MLD is used for both Fronthaul and Backhaul operation. {{bibref|EasyMesh}} source: Backhaul STA MLD Configuration TLV. The time in {{units}} since this STA MLD was associated. The total number of bytes transmitted to the STA MLD. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. The total number of bytes received from the STA MLD. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. The total number of packets transmitted to the STA MLD. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. The total number of packets received from the STA MLD. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. The number of packets which could not be transmitted to the STA MLD due to errors. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. The number of packets which were received with error from the STA MLD. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. The number of packets transmitted with the retry flag sent to the STA MLD. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. Pairwise AKM suite selector selected by the STA MLD. The Pairwise AKM suite selector (OUI and type) is encoded as a 4-octet hex-encoded value without internal delimiters, e.g. 506F9A02 {{bibref|802.11-2020|Table 9-151}}. Pairwise AKM cipher selector selected by the STA MLD. The Pairwise AKM cipher selector (OUI and type) is encoded as a 4-octet hex-encoded value without internal delimiters, e.g. 506F9A02 {{bibref|802.11-2020|Table 9-149}}. The RSN Capabilities selected by the STA MLD during association {{bibref|802.11-2020|Section 9.4.2.24.4}}. {{numentries}} {{numentries}} This object describes the Wi-Fi 7 capabilities for this STA MLD including Multi-Link Operation (MLO) capabilities. {{bibref|EasyMesh}} Source: Wi-Fi 7 Agent Capabilities TLV. Indicates if the Enhanced Multi-Link Multi-Radio (EMLMR) operation is supported by this STA MLD. Indicates if Enhanced Multi-Link Single-Radio (EMLSR) operation is supported by this STA MLD. Indicates if Simultaneous Transmit and Receive (STR) operation is supported by this STA MLD. Indicates if Non-Simultaneous Transmit and Receive (NSTR) operation is supported by this STA MLD. Indicates if Traffic Identifier (TID) to Link Mapping Negotiation is supported by this STA MLD. This object describes the Wi-Fi 7 Multi-Link Operation (MLO) configuration of the Multi-Link Device (MLD) station (STA, also called associated device). Note this may differ from the WiFi7 capabilities of the device. {{bibref|EasyMesh}} source: Associated STA MLD Configuration Report TLV. Indicates if the Enhanced Multi-Link Multi-Radio (EMLMR) operation is enabled. Indicates if Enhanced Multi-Link Single-Radio (EMLSR) operation is enabled. Indicates if Simultaneous Transmit and Receive (STR) operation is enabled. Indicates if Non-Simultaneous Transmit and Receive (NSTR) operation is enabled. Indicates if Traffic Identifier (TID) to Link Mapping Negotiation is enabled. {{bibref|EasyMesh}} source: TID-to-Link Mapping Policy TLV. Table of Traffic Identifier (TID) to Link Mappings of the Multi-Link Operation (MLO) capable station (STA). Each table entry describes the mapping between a particular TID and direction and preferred link. {{bibref|EasyMesh}} source: TID-to-Link Mapping Policy TLV. This object describes stations (STAs, also called associated devices) that are affiliated to this Multi-Link Device (MLD) STA. {{bibref|EasyMesh}} source: Associated STA MLD Configuration TLV. The MAC address of the affiliated STA. {{bibref|EasyMesh}} source: Associated STA MLD Configuration Report TLV. The BSSID of the affiliated AP that the affiliated STA is associated to. {{bibref|EasyMesh}} source: Associated STA MLD Configuration Report TLV. The total number of bytes transmitted to the affiliated STA. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. The total number of bytes received from the affiliated STA. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. The total number of packets transmitted to the affiliated STA. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. The total number of packets received from the affiliated STA. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. The number of packets which could not be transmitted to the affiliated STA due to errors. {{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV. An indicator of radio signal strength of the uplink from the affiliated STA to the access point - measured in {{units}}. RCPI is encoded per {{bibref|802.11-2020|Table 9-176}}, and described in {{bibref|EasyMesh|Section 10.3.1}}). Reserved: 221 - 255. Estimate of the MAC layer throughput in {{units}} achievable in the downlink direction if 100% of channel airtime and BSS operating bandwidth were available, as defined in {{bibref|EasyMesh|Section 10.3.1}}. Estimate of the MAC layer throughput in {{units}} achievable in the uplink direction if 100% of channel airtime and BSS operating bandwidth were available, as defined in {{bibref|EasyMesh|Section 10.3.1}}. The data transmit rate in {{units}} that was most recently used for transmission of data from the access point to the affiliated STA. The data transmit rate in {{units}} that was most recently used for transmission of data from the affiliated STA to the access point. The amount of time in {{units}} that the AP MLD Radio has spent on the channel receiving data from the affiliated STA. The amount of time in {{units}} that the AP MLD Radio has spent on the channel transmitting data to the affiliated STA.