PendingScheduleInforms

dateTime[]

R

Comma-separated list of date/times. Each entry in the list represents the absolute time at which the CPE is going to send a ScheduleInform RPC to the ACS. An empty string means that there are no pending ScheduledInform RPCs requested by the ACS.

-

2.20

UpgradePending

boolean

R

Indicates whether a firmware upgrade is scheduled or in progress. A value of true signifies that an upgrade is pending (e.g., scheduled after a delay) or is actively being performed. A value of false indicates no upgrade is scheduled or in progress.

The device MUST NOT enter a low-power state (I.e. Deep Standby) that could interrupt network connectivity or break the firmware upgrade process while this parameter is true.

-

2.20

DeliveredEvents

string[]

R

Comma-separated list of strings. Each entry represents an Event Code and its associated Command Key, where applicable as defined in [Section 3.7.1.5/TR-069], that was delivered to the ACS during the last session. The format for each entry is the Event Code itself followed by the Command Key in parentheses with an empty set of parentheses if the Command Key is not applicable. Furthermore, any spaces in the values MUST be percent encoded as defined in [Chapter 3.2.2 Comma-separated Lists/TR-106]. E.g. DeliveredEvents = "4%20VALUE%20CHANGE,7%20TRANSFER%20COMPLETE,M%20Download(20326379)".

-

2.20

SessionStatus

string

R

This parameter indicates the session status of the CWMP Agent.

Enumeration of:

• Idle (No session is ongoing, the CWMP Agent is waiting for an event or Connection Request)
• InProgress (The CWMP Agent has an ongoing session with the ACS)

-

2.20

AllowAllIPv4

boolean

W

Allow incoming IP connections from any IPv4 address. The source prefixes defined in IPv4AllowedSourcePrefix will be ignored.

The default value SHOULD be true.

-

2.20

IPv4AllowedSourcePrefix

string[](:1024)

W

Comma-separated list (maximum number of characters 1024) of strings. Allow only incoming IP connections from the provided list of IPv4 prefixes.

When IPv4AllowedSourcePrefix is set to an empty string and AllowAllIPv4 is set to false, no incoming IP connections are allowed.

When AllowAllIPv4 is set true, IPv4AllowedSourcePrefix is ignored.

-

2.20

AllowAllIPv6

boolean

W

Allow incoming IP connections from any IPv6 address. The source prefixes defined in IPv6AllowedSourcePrefix will be ignored.

The default value SHOULD be true.

-

2.20

IPv6AllowedSourcePrefix

string[](:1024)

W

Comma-separated list (maximum number of characters 1024) of strings. Allow only incoming IP connections from the provided list of IPv6 prefixes.

When IPv6AllowedSourcePrefix is set to an empty string and AllowAllIPv6 is set to false, no incoming IP connections are allowed.

When AllowAllIPv6 is set true, IPv6AllowedSourcePrefix is ignored.

-

2.20

Mode

string

R

The current NR mode being used.

Enumeration of:

• Unknown (NR mode is unknown)
• Standalone (NR is operating in standalone mode. This mode is only valid when the SupportedAccessTechnologies is equal to NR)
• NonStandalone (NR is operating in non-standalone mode. This mode is only valid when the SupportedAccessTechnologies is equal to NR)

-

2.20

PowerCapability

string[]

R

Comma-separated list of strings. Describes the possible power states of the Interface regardless of its current administrative state.

Each list item is an enumeration of:

• On (Indicates that the Interface is powered on)
• Off (Indicates that the Interface is powered off, using no power. When powered off, the Interface must be properly stopped. In particular, if applicable, a dying gasp message on the interface MUST be properly administered according to the respective standards)
• LowPower (Indicates that the Interface is in a low-power state, using minimal power, OPTIONAL)

-

2.20

PowerStatus

string

R

Reports the current power status of the Interface.

The value MUST be a member of the list reported by the PowerCapability parameter, or else be Error.

Each list item is an enumeration of:

• On (Indicates that the Interface is powered on)
• Off (Indicates that the Interface is powered off, using no power. When powered off, the Interface must be properly stopped. In particular, if applicable, a dying gasp message on the interface MUST be properly administered according to the respective standards)
• LowPower (Indicates that the Interface is in a low-power state, using minimal power, OPTIONAL)

-

2.20

PowerCapability

string[]

R

Comma-separated list of strings. Describes the possible power states of the Port regardless of its current administrative state.

Each list item is an enumeration of:

• On (Indicates that the Port is powered on)
• Off (Indicates that the Port is powered off, using no power. When powered off, the Port must be properly stopped. In particular, if applicable, a dying gasp message on the interface MUST be properly administered according to the respective standards)
• LowPower (Indicates that the Port is in a low-power state, using minimal power, OPTIONAL)

-

2.20

PowerStatus

string

R

Reports the current power status of the Port.

The value MUST be a member of the list reported by the PowerCapability parameter, or else be Error.

Each list item is an enumeration of:

• On (Indicates that the Port is powered on)
• Off (Indicates that the Port is powered off, using no power. When powered off, the Port must be properly stopped. In particular, if applicable, a dying gasp message on the interface MUST be properly administered according to the respective standards)
• LowPower (Indicates that the Port is in a low-power state, using minimal power, OPTIONAL)

-

2.20

AllowedDeviceNumberOfEntries

unsignedInt

R

The number of entries in the AllowedDevice table.

-

2.20

AllowAllDevices

boolean

W

When set to true, all USB devices are allowed to connect to the Device and the configuration mentioned in USB.USBHosts.AllowedDevice. is ignored.

When set to false, only USB devices listed in USB.USBHosts.AllowedDevice. are allowed to connect to the Device. Any USB device not explicitly listed will be rendered inactive.

-

2.20

DeviceState

string

R

Indicates the low-level device state, directly mapping to the "Visible Device States" in [Table 9-1 Visible Device States/USB2.0].

Enumeration of:

• Attached (The device is physically connected to the USB port. This is the initial state upon connection, before the host has necessarily detected or powered it. See [Section 9.1.1.1 Attached/USB2.0])
• Powered (The device is receiving power from the host but has not yet been reset. The host is aware of the connection. See [Section 9.1.1.2 Powered/USB2.0])
• Default (The device has been reset by the host and is now communicating on the default address. It is waiting for the host to assign it a unique address. See [Section 9.1.1.3 Default/USB2.0])
• Address (A unique device address has been assigned by the host. The device is now in the Address state, ready for the host to learn about its capabilities by reading its descriptors. See [Section 9.1.1.4 Address/USB2.0])
• Configured (The device has been successfully configured by the host. It is now fully operational and its interfaces are active. See [Section 9.1.1.5 Configured/USB2.0])
• Suspended (The device is in a low-power state to conserve energy. It maintains its address and configuration but is not actively communicating until it receives a resume signal from the host. See [Section 9.1.1.6 Suspended/USB2.0])

-

2.20

IsAllowed

boolean

R

When true, the associated USB device is allowed to connect to the Device USB Host controller(s) based on the configuration in USB.USBHosts.AllowedDevice. and AllowAllDevices.

When false, the associated USB device is not allowed to connect.

-

2.20

Alias

string(:64)

W

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.

• Its value MUST start with a letter.

• If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix.

• The CPE MUST NOT change the parameter value.

The Agent MUST choose an initial value that doesn't conflict with any existing entries.

-

2.20

Enable

boolean

W

Enables or disables whether the corresponding allowed USB device entry is active. If set to true, the device defined by this entry is permitted to connect to the system. If false, the device is ignored even if its identifiers match.

-

2.20

Description

string(:64)

W

A user-friendly description of the allowed USB device entry.

-

2.20

DeviceClass

string

W

Classification criterion.

Class Code assigned by USB-IF, which can be expressed as a two-digit hexadecimal string (e.g., 00), but can also include a wildcard character. When 00, the device specifies its own class code. When FF, the class code is vendor-specific. The * wildcard may be used to match any value, either fully (e.g., *) or partially (e.g., F* or *3). When empty, the device is not classified by Device Class.

Possible patterns:

• <Empty> (an empty string)
• [0-9A-Fa-f*]{2}

-

2.20

DeviceSubClass

string

W

Classification criterion.

Subclass code assigned by USB-IF, expressed as a two-digit hexadecimal string (e.g., 01), but can also include a wildcard character. The * wildcard may be used to match any value, either fully (e.g., *) or partially (e.g., 0* or *3). When empty, the device is not classified by Device Subclass.

Possible patterns:

• <Empty> (an empty string)
• [0-9A-Fa-f*]{2}

-

2.20

DeviceProtocol

string

W

Classification criterion.

Protocol code assigned by USB-IF, expressed as a two-digit hexadecimal string (e.g., 02), but can also include a wildcard character. The * wildcard may be used to match any value, either fully (e.g., *) or partially (e.g., 0* or *2). When empty, the device is not classified by Device Protocol.

Possible patterns:

• <Empty> (an empty string)
• [0-9A-Fa-f*]{2}

-

2.20

ProductID

string

W

Classification criterion.

Product ID assigned by the manufacturer, expressed as a two- to four-digit hexadecimal string (e.g., 5678), but can also include a wildcard character. The * wildcard may be used to match any value, either fully (e.g., *) or partially (e.g., 5*). When empty, the device is not classified by Product ID.

Possible patterns:

• <Empty> (an empty string)
• [0-9A-Fa-f*]{4}

-

2.20

VendorID

string

W

Classification criterion.

Vendor ID assigned by USB-IF, expressed as a two- to four-digit hexadecimal string (e.g., 1234), but can also include a wildcard character. The * wildcard may be used to match any value, either fully (e.g., *) or partially (e.g., 1*). When empty, the device is not classified by Vendor ID.

Possible patterns:

• <Empty> (an empty string)
• [0-9A-Fa-f*]{4}

-

2.20

Interfaces

string[]

W

Comma-separated list of strings. Each item defines an allowed USB interface in the format 'InterfaceClass:InterfaceSubClass:InterfaceProtocol', using two-digit hexadecimal values (e.g., FF), but can also include a wildcard character.

The * wildcard may be used to match any value, either fully (e.g., *) or partially (e.g., F*).

A connected device is allowed only if all of its interfaces match entries in this list.

• InterfaceClass: USB Class Code (00 = per-interface class, FF = vendor-specific)
• InterfaceSubClass: USB Subclass Code
• InterfaceProtocol: USB Protocol Code

Example: An USB Device might expose two interfaces:

• 0xFF:0x02:0x01 for diagnostics
• 0xFF:0x02:0x02 for data

These can be allowed by listing both explicitly, or using patterns like FF:02:* or F*:0*:0*.

When empty, the device is not classified by Interfaces.

Each list item matches one of:

• <Empty> (an empty string)
• [0-9A-Fa-f*]{2}:[0-9A-Fa-f*]{2}:[0-9A-Fa-f*]{2}

-

2.20

Type

string

W

The type of HomePlug interface.

Enumeration of:

• Embedded (Indicates that this is a physical HomePlug interface embedded in the Device)
• Logical (Indicates that this is a logical HomePlug interface that operates over an Ethernet interface. It is used for gathering statistics from HomePlug devices in the network and should be used when no embedded HomePlug interface is available in the Device)

-

2.20

Interface

string

W

The value MUST be the Path Name of a row in the Ethernet.Link. or Logical.Interface. tables, or the Path Name of an interface layered above such a row, e.g., a row in the Logical.Interface. table. If the referenced object is deleted, the parameter value MUST be set to an empty string. The Layer 2 Ethernet Interface over which the network protocol operates, when the Type parameter is Logical.

-

2.20

Manufacturer

string(:64)

R

The manufacturer of the remote HomePlug device.

-

2.20

FirmwareVersion

string

R

The firmware version of the remote HomePlug device.

-

2.20

RadioTemplateRef

string

R

The value MUST be the Path Name of a row in the Templates.RadioTemplate. table. If the referenced object is deleted, the parameter value MUST be set to an empty string. RadioTemplateRef is a reference to the RadioTemplate selected for this Radio.

-

2.20

BSSTemplateRef

string

R

The value MUST be the Path Name of a row in the Templates.BSSTemplate. table. If the referenced object is deleted, the parameter value MUST be set to an empty string. BSSTemplateRef is a reference to the BSSTemplate selected for this BSS.

-

2.20

SecurityTemplateRef

string

R

The value MUST be the Path Name of a row in the Templates.SecurityTemplate. table. If the referenced object is deleted, the parameter value MUST be set to an empty string. SecurityTemplateRef is a reference to the SecurityTemplate selected for this BSS.

-

2.20

APMLDTemplateRef

string

R

The value MUST be the Path Name of a row in the Templates.APMLDTemplate. table. If the referenced object is deleted, the parameter value MUST be set to an empty string. APMLDTemplateRef is a reference to the APMLDTemplate selected for this APMLD.

-

2.20

BSSTemplateNumberOfEntries

unsignedInt

R

The number of entries in the BSSTemplate table.

-

2.20

RadioTemplateNumberOfEntries

unsignedInt

R

The number of entries in the RadioTemplate table.

-

2.20

SecurityTemplateNumberOfEntries

unsignedInt

R

The number of entries in the SecurityTemplate table.

-

2.20

SecurityGroupNumberOfEntries

unsignedInt

R

The number of entries in the SecurityGroup table.

-

2.20

APMLDTemplateNumberOfEntries

unsignedInt

R

The number of entries in the APMLDTemplate table.

-

2.20

SSCTemplateNumberOfEntries

unsignedInt

R

The number of entries in the SSCTemplate table.

-

2.20

Enable

boolean

W

Indicates whether any BSS may be deployed in the Wi-Fi network.

true: BSS(s) are deployed according to the template matching process.

false: No BSS is deployed in the network.

-

2.20

TopologyFlag

string[]

W

The TopologyFlag is used to specify a list of EasyMesh Agents on which BSS(es) are deployed according to the template matching process. If an EasyMesh Agent does not match any value in the list, then no BSS is deployed on this EasyMesh Agent.

These values refer to the network topology role of the EasyMesh Agent as determined by the EasyMesh Controller.

This flag matches if any of the list items match (logical OR).

Comma-separated list of strings. Each list item is an enumeration of:

• Root (Colocated with the EasyMesh Controller)
• Repeater (Not colocated with the EasyMesh Controller)
• Wired_Repeater (Uses wired backhaul, i.e. all links between this EasyMesh Agent and the EasyMesh Controller are wired)
• Wireless_Repeater (Uses wireless backhaul, i.e. at least one link between this EasyMesh Agent and the EasyMesh Controller is wireless)
• ALID (Indicates an IEEE 1905 ALID, the value of which is a list item in IEEE1905ALID)

-

2.20

IEEE1905ALID

string(:17)[]

W

[MACAddress] Comma-separated list of MAC Addresses. IEEE 1905 [IEEE1905.1a] Abstraction-Layer ID (ALID).

This matches if any of the list items match (logical OR). This should match an entry in DataElements.Network.Device.{i}.ID.

-

2.20

PrimarySSCTemplateReference

string

W

The value MUST be the Path Name of a row in the SSCTemplate. table. If the referenced object is deleted, the parameter value MUST be set to an empty string. Incicates the Primary SSCTemplate.

The PrimaryVLANID in the EasyMesh network is the VLANID of the SSCTemplate referenced by PrimarySSCTemplateReference. If this value is empty, then Traffic Separation is not used. [Section 19/EasyMesh].

-

2.20

PrimarySSCTemplateID

string

R

Indicates the Primary SSCTemplate.

The value must be the SSCTemplate.{i}.SSCTemplateID to identify an instance of SSCTemplate. If this value is empty, then Traffic Separation is not used. [Section 19/EasyMesh].

-

2.20

Alias

string(:64)

W

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.

• Its value MUST start with a letter.

• If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix.

• The CPE MUST NOT change the parameter value.

The Agent MUST choose an initial value that doesn't conflict with any existing entries.

-

2.20

BSSTemplateID

string

WO

Static and persistent ID element. At most one BSSTemplate instance can exist with a given value for BSSTemplateID.

Once it's been set, this parameter is immutable.

-

2.20

Priority

unsignedInt(:255)

W

This value indicates in which order the BSSTemplate are to be matched for a reported radio. 255 is the highest priority, 0 is the lowest priority.

-

2.20

RadioTemplateReference

string

W

The value MUST be the Path Name of a row in the RadioTemplate. table. If the referenced object is deleted, the parameter value MUST be set to an empty string. This BSSTemplate is linked to RadioTemplateReference.

-

2.20

SSCTemplateReference

string

W

The value MUST be the Path Name of a row in the SSCTemplate. table. If the referenced object is deleted, the parameter value MUST be set to an empty string. This BSSTemplate is linked to SSCTemplateReference.

-

2.20

APMLDTemplateReference

string

W

The value MUST be the Path Name of a row in the APMLDTemplate. table. If the referenced object is deleted, the parameter value MUST be set to an empty string. This BSSTemplate is linked to APMLDTemplateReference.

-

2.20

SecurityGroupReference

string

W

The value MUST be the Path Name of a row in the SecurityGroup. table. If the referenced object is deleted, the parameter value MUST be set to an empty string. This BSSTemplate is linked to SecurityGroupReference.

-

2.20

LinkedRadioTemplateID

string

R

Indicates the RadioTemplate.{i}.RadioTemplateID that is linked with this BSSTemplate.

-

2.20

LinkedSSCTemplateID

string

R

Indicates the SSCTemplate.{i}.SSCTemplateID that is linked with this BSSTemplate.

-

2.20

LinkedAPMLDTemplateID

string

R

Indicates the APMLDTemplate.{i}.APMLDTemplateID that is linked with this BSSTemplate.

-

2.20

LinkedSecurityGroupID

string

R

Indicates the SecurityGroup.{i}.SecurityGroupID of the SecurityGroup.{i} in which a matching SecurityTemplate is searched.

-

2.20

TopologyFlag

string[]

W

The topology flag is used to specify a list of EasyMesh Agents for which this BSSTemplate is considered by the Configuration Template Manager during the matching process. If an Agent does not match any value in the list, then no BSS matching this BSSTemplate is deployed on the EasyMesh Agent. These values refer to the network topology point of the EasyMesh Agent as determined by the EasyMesh Controller.

This flag matches if any of the list items match (logical OR).

Comma-separated list of strings. Each list item is an enumeration of:

• Root (Colocated with the EasyMesh Controller)
• Repeater (Not colocated with the EasyMesh Controller)
• Wired_Repeater (Uses wired backhaul, i.e. all links between this EasyMesh Agent and the EasyMesh Controller are wired)
• Wireless_Repeater (Uses wireless backhaul, i.e. at least one link between this EasyMesh Agent and the EasyMesh Controller is wireless)
• ALID (Indicates an IEEE 1905 ALID, the value of which is a list item in IEEE1905ALID)

-

2.20

IEEE1905ALID

string(:17)[]

W

[MACAddress] Comma-separated list of MAC Addresses. IEEE 1905 [IEEE1905.1a] Abstraction-Layer ID (ALID).

This flag matches if any of the list items match (logical OR). This should match an entry in DataElements.Network.Device.{i}.ID.

-

2.20

MaxWLANHopLimitFlag

unsignedInt(:255)

W

Indicates the maximum number of wireless hops (consecutive or not) allowed between the EasyMesh Controller and the EasyMesh Agent.

In single-AP deployment, this flag is ignored.

-

2.20

SecureEquipmentFlag

string

W

Indicates the 1905 Security of the EasyMesh Agent [Section 17.2.77/EasyMesh]. Enumeration of:

• true (Indicates that 1905 Security is supported and being used by the EasyMesh Agent)
• false (Indicates that 1905 Security is not being used by the EasyMesh Agent)
• null (No requirement for matching)

-

2.20

Enable

boolean

W

Determines if this template is considered by the Configuration Template Manager in the template matching process.

-

2.20

SSID

string

W

The Service Set Identifier (SSID) used as an identifier by all deployed BSSs linked to this BSSTemplate.

-

2.20

KeyPassphrase

string

W

The KeyPassphrase to be used by all deployed BSSs linked to this BSSTemplate.

When read, this parameter returns an empty string, regardless of the actual value.

-

2.20

AdvertisementEnable

boolean

W

Indicates if the SSID is advertised in beacons

true: this SSID is to be advertised in beacons.

false: this SSID is not to be advertised in beacons.

-

2.20

Alias

string(:64)

W

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.

• Its value MUST start with a letter.

• If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix.

• The CPE MUST NOT change the parameter value.

The Agent MUST choose an initial value that doesn't conflict with any existing entries.

-

2.20

RadioTemplateID

string

WO

Static and persistent ID element. At most one RadioTemplate instance can exist with a given value for RadioTemplateID.

Note that RadioTemplateID is not the same as DataElements.Network.Device.{i}.Radio.{i}.ID.

Once it's been set, this parameter is immutable.

-

2.20

Priority

unsignedInt(:255)

W

This value indicates in which order the RadioTemplate are to be matched for a radio under configuration. 255 is the highest priority, 0 is the lowest priority.

-

2.20

Enable

boolean

W

Determines if this RadioTemplate is considered by the Configuration Template Manager (CTM) in the template matching process.

This value is independent from the value of any Radio.{i}.Enable. This value is also independent from the value of any DataElements.Network.Device.{i}.Radio.{i}.Enabled.

-

2.20

OpClassFlag

unsignedInt(:255)[]

W

Comma-separated list of unsigned integers (up to 255). Each list item is a global valid operating class as defined in [Table E-4/802.11ax]).

Indicates the Operating Classes the Radio can operate on. Exactly one of OpClassFlag or BandFlag must be empty and exactly one must be filled in.

A Radio must be able to operate on at least one channel of each Operating Class specified in this list to satisfy this condition.

-

2.20

BandFlag

string[]

W

Indicates frequency bands the Radio can operate on. All listed UNII bands are to be in the same 2.4, 5 or 6 GHz band.

Exactly one of OpClassFlag or BandFlag must be empty.

Comma-separated list of strings. Each list item is an enumeration of:

• 2.4 (2.4 GHz band)
• 5 (The entire 5 GHz band)
• 6 (The entire 6 GHz band)
• 5_UNII_1 (5 GHz UNII-1 band, 5.15 to 5.25 GHz)
• 5_UNII_2 (5 GHz UNII-2 band, 5.25 to 5.725 GHz)
• 5_UNII_3 (5 GHz UNII-3 band, 5.725 to 5.85 GHz)
• 5_UNII_4 (5 GHz UNII-4 band, 5.85 to 5.925 GHz)
• 6_UNII_5 (6 GHz UNII-5 band, 5.925 to 6.425 GHz)
• 6_UNII_6 (6 GHz UNII-6 band, 6.425 to 6.525 GHz)
• 6_UNII_7 (6 GHz UNII-7 band, 6.525 to 6.875 GHz)
• 6_UNII_8 (6 GHz UNII-8 band, 6.875 to 7.125 GHz)
• Sub_1GHz (Sub 1 GHz band, 800 MHz to 928 MHz)

-

2.20

SupportedGenerationFlag

unsignedInt(1:255)[]

W

Comma-separated list of unsigned integers (1 to 255). Each list item indicates a supported Wi-Fi Generation. Each list item indicates a Supported Generation of Generational Capabilities Indication attribute.

For example SupportedGenerationFlag could be "5,6,7".

-

2.20

DFSSupportFlag

string

W

Indicates Dynamic Frequency Selection (DFS) support. Enumeration of:

• true (Device supports DFS)
• false (Device does not support DFS)
• null (No requirement for matching)

-

2.20

AFCSupportFlag

string

W

Indicates Automated Frequency Coordination (AFC) support. Enumeration of:

• true (Device supports AFC)
• false (Device does not support AFC)
• null (No requirement for matching)

-

2.20

TransmitPowerLimit

int(-128:127)

W

This is the upper limit on nominal transmit Equivalent Isotropically Radiated Power (EIRP) that this radio is allowed to use for the current operating class. In units of decibels relative to 1 mW dBm.

-

2.20

OperatingGeneration

string[]

W

Comma-separated list of strings. Each list item indicates a Wi-Fi Generation deployed on this EasyMesh Agent or this device. The last list item may be followed by a "+" to indicate the inclusion of any existing Wi-Fi Generation above it. If an EasyMesh agent or device supports a Wi-Fi Generation not in the list, then that Wi-Fi Generation is disabled on the EasyMesh agent or device.

For example, "6,7+" means Wi-Fi 6, Wi-Fi 7 and any newer Wi-Fi Generation.

Note: OperatingGeneration may include Wi-Fi Generations not supported by a radio to which this RadioTemplate is deployed.

-

2.20

Alias

string(:64)

W

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.

• Its value MUST start with a letter.

• If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix.

• The CPE MUST NOT change the parameter value.

The Agent MUST choose an initial value that doesn't conflict with any existing entries.

-

2.20

SecurityTemplateID

string

WO

Static and persistent ID element. At most one SecurityTemplate instance can exist with a given value for SecurityTemplateID.

Once it's been set, this parameter is immutable.

-

2.20

Enable

boolean

W

Determines if this template is considered by the Configuration Template Manager in the template matching process.

-

2.20

Priority

unsignedInt(:255)

W

This value indicates in which order the SecurityTemplate are to be matched. 255 is the highest priority, 0 is the lowest priority.

-

2.20

RSNOSupportFlag

string

W

Indicates support for Robust Security Network (RSN) Overriding (RSNO). RSN Overriding (RSNO) is also known as MRSNO and is used in WPA3-Personal Compatibility Mode. Enumeration of:

• true (The AP shall indicate support for RSNO for this flag to match)
• false (The AP shall not indicate support for RSNO for this flag to match)
• null (This flag matches in all cases)

-

2.20

SupportedAKMSuiteFlag

string[]

W

Comma-separated list of strings. Authentication and Key Management (AKM) suite selector. Only the listed enumeration values are allowed in this string. Each list item is an enumeration of:

• psk (indicates AKM 00-0F-AC:2)
• dpp (indicates AKM 50-6F-9A:2)
• sae (indicates AKM 00-0F-AC:8)
• sae-ext-key (indicates AKM 00-0F-AC:24)
• SuiteSelector (indicates an AKM suite selector, the value of which is indicated in SupportedAKMSuiteSelectorFlag)

-

2.20

SupportedAKMSuiteSelectorFlag

hexBinary(4)[]

W

Comma-separated list of Hex binarys (length 4). AKM suite selector, the AKM suite selector (OUI and type) is encoded as a 4-octet hex-encoded value without internal delimiters, e.g. 506F9A02 [Table 9-151/802.11-2020].

SupportedAKMSuiteSelectorFlag applies if SupportedAKMSuiteFlag includes value "SuiteSelector".

-

2.20

OperatingGenerationFlag

unsignedInt(1:255)[]

W

Comma-separated list of unsigned integers (1 to 255). The AP advertises support in its beacon frames for each Wi-Fi generation in this list for this flag to match.

For example OperatingGenerationFlag could be "5,6,7".

-

2.20

SecurityIEs

hexBinary

W

Concatenation of all BSS Security related IEs with Element IDs, without delimiters as hex encoded octets [EasyMesh].

Note that this SecurityIEs and the RSNE, RSNOE, RSNO2E, RSNXE, RSNXOE objects are independent and may be set separately. If this SecurityIEs is not empty, the Configuration Template Manager (CTM) uses the value of this SecurityIEs and ignores the content of the RSNE/RSNOE/RSNO2E/RSNXE/RSNXOE objects.

-

2.20

GroupDataCipherSuite

string

W

Cipher suite selector used to protect group addressed data frames. This is the name of a cipher suite, as defined in [Table 9-149/802.11-2020].

The following is an example value: "CCMP-128".

-

2.20

PairwiseCipherSuite

string[]

W

Comma-separated list of strings. Each list item is a cipher suite selector used to protect individually addressed Data frames, as defined in [Table 9-149/802.11-2020].

The following is an example value: "CCMP-128".

-

2.20

AKMSuite

string[]

W

Authentication and Key Management (AKM) suite [Table 9-151/802.11-2020]. Comma-separated list of strings. Each list item is an enumeration of:

• psk (indicates AKM 00-0F-AC:2)
• dpp (indicates AKM 50-6F-9A:2)
• sae (indicates AKM 00-0F-AC:8)
• sae-ext-key (indicates AKM 00-0F-AC:24)
• SuiteSelector (indicates an AKM suite selector, the value of which is indicated in AKMSuiteSelector)

-

2.20

AKMSuiteSelector

hexBinary(4)[]

W

Comma-separated list of Hex binarys (length 4). AKM suite selector, the AKM suite selector (OUI and type) is encoded as a 4-octet hex-encoded value without internal delimiters, e.g. 506F9A02 [Table 9-151/802.11-2020].

AKMSuiteSelector applies if AKMSuite includes value "SuiteSelector".

-

2.20

MFP

string

W

Indicates the expected support for Management Frame Protection (MFP), aka Protected Management Frame (PMF).

[WPA3v3.0] and see also the WPA3 and Wi-Fi Enhanced Open Deployment Guide v1.1.pdf, Table 3, row PMF.

Enumeration of:

• Disabled
• Capable
• Required

-

2.20

GroupManagementCipherSuite

string

W

Cipher suite selector used to protect group addressed robust Management frames. This is the name of a cipher suite, as defined in [Table 9-149/802.11-2020].

The following is an example value: "BIP-CMAC-128".

-

2.20

GroupDataCipherSuite

string

W

Cipher suite selector used to protect group addressed data frames. This is the name of a cipher suite, as defined in [Table 9-149/802.11-2020].

The following is an example value: "CCMP-128".

-

2.20

PairwiseCipherSuite

string[]

W

Comma-separated list of strings. Each list item is a cipher suite selector used to protect individually addressed Data frames, as defined in [Table 9-149/802.11-2020].

The following is an example value: "CCMP-128".

-

2.20

AKMSuite

string[]

W

Authentication and Key Management (AKM) suite [Table 9-151/802.11-2020]. Comma-separated list of strings. Each list item is an enumeration of:

• psk (indicates AKM 00-0F-AC:2)
• dpp (indicates AKM 50-6F-9A:2)
• sae (indicates AKM 00-0F-AC:8)
• sae-ext-key (indicates AKM 00-0F-AC:24)
• SuiteSelector (indicates an AKM suite selector, the value of which is indicated in AKMSuiteSelector)

-

2.20

AKMSuiteSelector

hexBinary(4)[]

W

Comma-separated list of Hex binarys (length 4). AKM suite selector, the AKM suite selector (OUI and type) is encoded as a 4-octet hex-encoded value without internal delimiters, e.g. 506F9A02 [Table 9-151/802.11-2020].

AKMSuiteSelector applies if AKMSuite includes value "SuiteSelector".

-

2.20

MFP

string

W

Indicates the expected support for Management Frame Protection (MFP), aka Protected Management Frame (PMF).

[WPA3v3.0] and see also the WPA3 and Wi-Fi Enhanced Open Deployment Guide v1.1.pdf, Table 3, row PMF.

Enumeration of:

• Disabled
• Capable
• Required

-

2.20

GroupManagementCipherSuite

string

W

Cipher suite selector used to protect group addressed robust Management frames. This is the name of a cipher suite, as defined in [Table 9-149/802.11-2020].

The following is an example value: "BIP-CMAC-128".

-

2.20

GroupDataCipherSuite

string

W

Cipher suite selector used to protect group addressed data frames. This is the name of a cipher suite, as defined in [Table 9-149/802.11-2020].

The following is an example value: "CCMP-128".

-

2.20

PairwiseCipherSuite

string[]

W

Comma-separated list of strings. Each list item is a cipher suite selector used to protect individually addressed Data frames, as defined in [Table 9-149/802.11-2020].

The following is an example value: "CCMP-128".

-

2.20

AKMSuite

string[]

W

Authentication and Key Management (AKM) suite [Table 9-151/802.11-2020]. Comma-separated list of strings. Each list item is an enumeration of:

• psk (indicates AKM 00-0F-AC:2)
• dpp (indicates AKM 50-6F-9A:2)
• sae (indicates AKM 00-0F-AC:8)
• sae-ext-key (indicates AKM 00-0F-AC:24)
• SuiteSelector (indicates an AKM suite selector, the value of which is indicated in AKMSuiteSelector)

-

2.20

AKMSuiteSelector

hexBinary(4)[]

W

Comma-separated list of Hex binarys (length 4). AKM suite selector, the AKM suite selector (OUI and type) is encoded as a 4-octet hex-encoded value without internal delimiters, e.g. 506F9A02 [Table 9-151/802.11-2020].

AKMSuiteSelector applies if AKMSuite includes value "SuiteSelector".

-

2.20

MFP

string

W

Indicates the expected support for Management Frame Protection (MFP), aka Protected Management Frame (PMF).

[WPA3v3.0] and see also the WPA3 and Wi-Fi Enhanced Open Deployment Guide v1.1.pdf, Table 3, row PMF.

Enumeration of:

• Disabled
• Capable
• Required

-

2.20

GroupManagementCipherSuite

string

W

Cipher suite selector used to protect group addressed robust Management frames. This is the name of a cipher suite, as defined in [Table 9-149/802.11-2020].

The following is an example value: "BIP-CMAC-128".

-

2.20

SAEH2E

boolean

W

Indicates if the BSS will support Simultaneous Authentication of Equals (SAE) hash-to-element true, or not false.

true: BSS sets SAE hash-to-element to 1. false: BSS sets SAE hash-to-element to 0.

-

2.20

SAEH2E

boolean

W

Indicates if the BSS will support Simultaneous Authentication of Equals (SAE) hash-to-element true, or not false.

true: BSS sets SAE hash-to-element to 1. false: BSS sets SAE hash-to-element to 0.

-

2.20

SecurityGroupID

string

W

This is the friendly name of this SecurityGroup which may be advertised to the end user in a graphical interface.

The Agent MUST choose an initial value that doesn't conflict with any existing entries.

-

2.20

SecurityTemplateReferences

string[]

W

Comma-separated list of strings. Each list item MUST be the Path Name of a row in the SecurityTemplate. table. If the referenced object is deleted, the corresponding item MUST be removed from the list. Indicates the list of SecurityTemplate for this SecurityGroup.

-

2.20

LinkedSecurityTemplateID

string[]

R

Comma-separated list of strings. Indicates the SecurityTemplate.{i}.SecurityTemplateID in this entry of this SecurityGroup.

-

2.20

Alias

string(:64)

W

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.

• Its value MUST start with a letter.

• If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix.

• The CPE MUST NOT change the parameter value.

The Agent MUST choose an initial value that doesn't conflict with any existing entries.

-

2.20

APMLDTemplateID

string

WO

Static and persistent ID element. At most one APMLDTemplate instance can exist with a given value for APMLDTemplateID.

Once it's been set, this parameter is immutable.

-

2.20

MLOEnable

boolean

W

Indicates whether or not Multi-Link Operation (MLO) is enabled. If set to false, then MLO support is disabled and each deployment of a BSSTemplate related to this APMLDTemplate results in an AP MLD with a single affiliated AP. However, this does not disable the BSSs that are in the BSSTemplate.{i} linked to this APMLDTemplate.

-

2.20

STREnable

boolean

W

Indicates whether or not Simultaneous Transmit and Receive (STR) mode is to be enabled on the AP MLD.

-

2.20

NSTREnable

boolean

W

Indicates whether or not Non-Simultaneous Transmit and Receive (NSTR) mode is to be enabled on the AP MLD.

-

2.20

EMLSREnable

boolean

W

Indicates whether or not Enhanced Multi-Link Single-Radio (EMLSR) mode is to be enabled on the AP MLD.

-

2.20

EMLMREnable

boolean

W

Indicates whether or not Enhanced Multi-Link Multi-Radio (EMLMR) mode is to be enabled on the AP MLD.

-

2.20

TIDToLinkMapNegotiation

boolean

W

Indicates whether the TID-to-link Mapping Negotiation Support subfield in the MLD Capabilities and Operations field of the Basic Multi-Link element is (to be) enabled by any deployed AP MLD linked to this APMLDTemplate.

-

2.20

Alias

string(:64)

W

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.

• Its value MUST start with a letter.

• If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix.

• The CPE MUST NOT change the parameter value.

The Agent MUST choose an initial value that doesn't conflict with any existing entries.

-

2.20

SSCTemplateID

string

WO

Static and persistent ID element. At most one SSCTemplate instance can exist with a given value for SSCTemplateID.

Once it's been set, this parameter is immutable.

-

2.20

SSCEnable

boolean

W

If set to false, then all BSSs that are linked with this SSCTemplate are disabled, which means that these BSSs cease to offer service.

-

2.20

VID

unsignedInt(:4095)

W

The VLAN ID (VID) for all BSSs that are part of this SSCTemplate. A value of 0 indicates that no VLAN shall be configured on the BSSs belonging to this SSCTemplate.

-

2.20

HaulType

string[]

W

Indicates the use of the BSSs that are part of this SSCTemplate. Comma-separated list of strings. Each list item is an enumeration of:

• Fronthaul
• Backhaul

-

2.20

PowerCapability

string[]

R

Comma-separated list of strings. Describes the possible power states of the Radio regardless of its current administrative state.

Each list item is an enumeration of:

• On (Indicates that the Radio is powered on)
• Off (Indicates that the Radio is powered off, using no power. When powered off, the Radio must be properly stopped. In particular, if applicable, a dying gasp message on the interface MUST be properly administered according to the respective standards)
• LowPower (Indicates that the Radio is in a low-power state, using minimal power, OPTIONAL)

-

2.20

PowerStatus

string

R

Reports the current power status of the Radio.

The value MUST be a member of the list reported by the PowerCapability parameter, or else be Error.

Each list item is an enumeration of:

• On (Indicates that the Radio is powered on)
• Off (Indicates that the Radio is powered off, using no power. When powered off, the Radio must be properly stopped. In particular, if applicable, a dying gasp message on the interface MUST be properly administered according to the respective standards)
• LowPower (Indicates that the Radio is in a low-power state, using minimal power, OPTIONAL)

-

2.20

ConfiguredReceiveAntennas

int(-1,0:255)

W

The bit pattern of the configured receive antennas that need to be activated.

This parameter uses a bitmap to specify which receive antennas need to be enabled. Each bit in the unsigned integer corresponds to a specific antenna. If a bit is set to '1', the corresponding antenna is activated for reception. If a bit is set to '0', the antenna is deactivated.

How the Bitmap Works:

• Bit 0 (LSB): Corresponds to Antenna 0. If the value is odd (e.g., 1, 3, 5...), Antenna 0 is enabled.
• Bit 1: Corresponds to Antenna 1.
• Bit 2: Corresponds to Antenna 2.
• And so on...
• Bit N: Corresponds to Antenna N.

Examples:

• 0: No receive antennas are activated.
• 1: Only Antenna 0 is activated for reception.
• 2: Only Antenna 1 is activated for reception.
• 3: Antenna 0 and Antenna 1 are activated for reception.
• 255: All 8 possible receive antennas (Antenna 0 through Antenna 7) are activated.

The value MUST be within the range of SupportedReceiveAntennas, meaning you cannot attempt to activate an antenna that is not physically supported by the device.

Valid values are: -1 (A value of -1 indicates the automatic selection of the receive antennas), or 0 to 255.

-

2.20

ConfiguredTransmitAntennas

int(-1,0:255)

W

The bit pattern of the configured transmit antennas that need to be activated.

This parameter uses a bitmap to specify which receive antennas need to be enabled. Each bit in the unsigned integer corresponds to a specific antenna. If a bit is set to '1', the corresponding antenna is activated for reception. If a bit is set to '0', the antenna is deactivated.

How the Bitmap Works:

• Bit 0 (LSB): Corresponds to Antenna 0. If the value is odd (e.g., 1, 3, 5...), Antenna 0 is enabled.
• Bit 1: Corresponds to Antenna 1.
• Bit 2: Corresponds to Antenna 2.
• And so on...
• Bit N: Corresponds to Antenna N.

Examples:

• 0: No receive antennas are activated.
• 1: Only Antenna 0 is activated for reception.
• 2: Only Antenna 1 is activated for reception.
• 3: Antenna 0 and Antenna 1 are activated for reception.
• 255: All 8 possible receive antennas (Antenna 0 through Antenna 7) are activated.

The value MUST be within the range of SupportedReceiveAntennas, meaning you cannot attempt to activate an antenna that is not physically supported by the device.

Valid values are: -1 (A value of -1 indicates the automatic selection of the transmit antennas), or 0 to 255.

-

2.20

SupportedReceiveAntennas

int(0:8,-1)

R

Specifies the maximum number of antennas, used for receiving on this radio.

Valid values are: 0 to 8, or -1 (A value of -1 means that this feature is not supported).

-

2.20

SupportedTransmitAntennas

int(0:8,-1)

R

Specifies the maximum number of antennas, used for receiving on this radio.

Valid values are: 0 to 8, or -1 (A value of -1 means that this feature is not supported).

-

2.20

ActiveReceiveAntennas

int(0:255,-1)

R

The bit pattern of the receive antennas actively in use.

This parameter uses a bitmap to specify which receive antennas are enabled. Each bit in the unsigned integer corresponds to a specific antenna. If a bit is set to '1', the corresponding antenna is activated for reception. If a bit is set to '0', the antenna is deactivated.

Valid values are: 0 to 255, or -1 (A value of -1 means that this feature is not supported).

-

2.20

ActiveTransmitAntennas

int(0:255,-1)

R

The bit pattern of the transmit antennas actively in use.

This parameter uses a bitmap to specify which transmit antennas are enabled. Each bit in the unsigned integer corresponds to a specific antenna. If a bit is set to '1', the corresponding antenna is activated for reception. If a bit is set to '0', the antenna is deactivated.

Valid values are: 0 to 255, or -1 (A value of -1 means that this feature is not supported).

-

2.20

EMLMRSupport

boolean

R

Indicates if the Enhanced Multi-Link Multi-Radio (EMLMR) operation is supported.

-

2.20

EMLSRSupport

boolean

R

Indicates if Enhanced Multi-Link Single-Radio (EMLSR) operation is supported.

-

2.20

STRSupport

boolean

R

Indicates if Simultaneous Transmit and Receive (STR) operation is supported.

-

2.20

NSTRSupport

boolean

R

Indicates if Non-Simultaneous Transmit and Receive (NSTR) operation is supported.

-

2.20

TIDLinkMapNegotiation

boolean

R

Indicates if Traffic Identifier (TID) to Link Mapping Negotiation is supported.

-

2.20

EMLMRFreqSeparationNumberOfEntries

unsignedInt

R

The number of entries in the EMLMRFreqSeparation table.

-

2.20

EMLSRFreqSeparationNumberOfEntries

unsignedInt

R

The number of entries in the EMLSRFreqSeparation table.

-

2.20

STRFreqSeparationNumberOfEntries

unsignedInt

R

The number of entries in the STRFreqSeparation table.

-

2.20

NSTRFreqSeparationNumberOfEntries

unsignedInt

R

The number of entries in the NSTRFreqSeparation table.

-

2.20

RUID

base64

R

The Radio unique identifier (RUID) of another radio to which the specified frequency separation gap applies.

-

2.20

FreqSeparation

unsignedInt

R

Frequency separation to the specified radio for the particular MLO operation mode. A value of 0 indicates that no frequency separation information is provided. Set to a nonzero value to indicate the required frequency gap is (FreqSeparation - 1) x 80 MHz.

-

2.20

RUID

base64

R

The Radio unique identifier (RUID) of another radio to which the specified frequency separation gap applies.

-

2.20

FreqSeparation

unsignedInt

R

Frequency separation to the specified radio for the particular MLO operation mode. A value of 0 indicates that no frequency separation information is provided. Set to a nonzero value to indicate the required frequency gap is (FreqSeparation - 1) x 80 MHz.

-

2.20

RUID

base64

R

The Radio unique identifier (RUID) of another radio to which the specified frequency separation gap applies.

-

2.20

FreqSeparation

unsignedInt

R

Frequency separation to the specified radio for the particular MLO operation mode. A value of 0 indicates that no frequency separation information is provided. Set to a nonzero value to indicate the required frequency gap is (FreqSeparation - 1) x 80 MHz.

-

2.20

RUID

base64

R

The Radio unique identifier (RUID) of another radio to which the specified frequency separation gap applies.

-

2.20

FreqSeparation

unsignedInt

R

Frequency separation to the specified radio for the particular MLO operation mode. A value of 0 indicates that no frequency separation information is provided. Set to a nonzero value to indicate the required frequency gap is (FreqSeparation - 1) x 80 MHz.

-

2.20

EMLMRSupport

boolean

R

Indicates if the Enhanced Multi-Link Multi-Radio (EMLMR) operation is supported.

-

2.20

EMLSRSupport

boolean

R

Indicates if Enhanced Multi-Link Single-Radio (EMLSR) operation is supported.

-

2.20

STRSupport

boolean

R

Indicates if Simultaneous Transmit and Receive (STR) operation is supported.

-

2.20

NSTRSupport

boolean

R

Indicates if Non-Simultaneous Transmit and Receive (NSTR) operation is supported.

-

2.20

TIDLinkMapNegotiation

boolean

R

Indicates if Traffic Identifier (TID) to Link Mapping Negotiation is supported.

-

2.20

EMLMRFreqSeparationNumberOfEntries

unsignedInt

R

The number of entries in the EMLMRFreqSeparation table.

-

2.20

EMLSRFreqSeparationNumberOfEntries

unsignedInt

R

The number of entries in the EMLSRFreqSeparation table.

-

2.20

STRFreqSeparationNumberOfEntries

unsignedInt

R

The number of entries in the STRFreqSeparation table.

-

2.20

NSTRFreqSeparationNumberOfEntries

unsignedInt

R

The number of entries in the NSTRFreqSeparation table.

-

2.20

RUID

base64

R

The Radio unique identifier (RUID) of another radio to which the specified frequency separation gap applies.

-

2.20

FreqSeparation

unsignedInt

R

Frequency separation to the specified radio for the particular MLO operation mode. A value of 0 indicates that no frequency separation information is provided. Set to a nonzero value to indicate the required frequency gap is (FreqSeparation - 1) x 80 MHz.

-

2.20

RUID

base64

R

The Radio unique identifier (RUID) of another radio to which the specified frequency separation gap applies.

-

2.20

FreqSeparation

unsignedInt

R

Frequency separation to the specified radio for the particular MLO operation mode. A value of 0 indicates that no frequency separation information is provided. Set to a nonzero value to indicate the required frequency gap is (FreqSeparation - 1) x 80 MHz.

-

2.20

RUID

base64

R

The Radio unique identifier (RUID) of another radio to which the specified frequency separation gap applies.

-

2.20

FreqSeparation

unsignedInt

R

Frequency separation to the specified radio for the particular MLO operation mode. A value of 0 indicates that no frequency separation information is provided. Set to a nonzero value to indicate the required frequency gap is (FreqSeparation - 1) x 80 MHz.

-

2.20

RUID

base64

R

The Radio unique identifier (RUID) of another radio to which the specified frequency separation gap applies.

-

2.20

FreqSeparation

unsignedInt

R

Frequency separation to the specified radio for the particular MLO operation mode. A value of 0 indicates that no frequency separation information is provided. Set to a nonzero value to indicate the required frequency gap is (FreqSeparation - 1) x 80 MHz.

-

2.20

MTU

unsignedInt

W

Maximum Transmission Unit for this interface (expressed in bytes).

-

2.20

SAEGroupDependantHashEnable

string

W

Enable SAE with group dependant hash usage in WPA3 security modes. This flag enables or disables the use of SAE with group dependant hash instead of simple SAE applicable when ModeEnabled is set to WPA3-Personal, WPA3-Personal-Transition, or WPA3-Enterprise. If SAEGroupDependantHashEnable is set to Disabled, then only AKM8 shall be used. If it is set to Transition, then both AKM8 and AKM24 shall be used. Finally, if SAEGroupDependantHashEnable is set to Enabled, then only AKM24 shall be used. Enabled is invalid when ModeEnabled is set to WPA3-Personal-Transition.

Enumeration of:

• Disabled
• Transition
• Enabled

Transition

2.20

SAEGroupDependantHashEnable

string

W

Enable SAE with group dependant hash usage in WPA3 security modes. This flag enables or disables the use of SAE with group dependant hash instead of simple SAE applicable when ModeEnabled is set to WPA3-Personal, WPA3-Personal-Transition, or WPA3-Enterprise. If SAEGroupDependantHashEnable is set to Disabled, then only AKM8 shall be used. If it is set to Transition, then both AKM8 and AKM24 shall be used. Finally, if SAEGroupDependantHashEnable is set to Enabled, then only AKM24 shall be used. Enabled is invalid when ModeEnabled is set to WPA3-Personal-Transition.

Enumeration of:

• Disabled
• Transition
• Enabled

Transition

2.20

PowerCapability

string[]

R

Comma-separated list of strings. Describes the possible power states of the Radio regardless of its current administrative state.

Each list item is an enumeration of:

• On (Indicates that the Radio is powered on)
• Off (Indicates that the Radio is powered off, using no power. When powered off, the Radio must be properly stopped. In particular, if applicable, a dying gasp message on the interface MUST be properly administered according to the respective standards)
• LowPower (Indicates that the Radio is in a low-power state, using minimal power, OPTIONAL)

-

2.20

PowerStatus

string

R

Reports the current power status of the Radio.

The value MUST be a member of the list reported by the PowerCapability parameter, or else be Error.

Each list item is an enumeration of:

• On (Indicates that the Radio is powered on)
• Off (Indicates that the Radio is powered off, using no power. When powered off, the Radio must be properly stopped. In particular, if applicable, a dying gasp message on the interface MUST be properly administered according to the respective standards)
• LowPower (Indicates that the Radio is in a low-power state, using minimal power, OPTIONAL)

-

2.20