If transmit PHY rate between all pairs of MoCA Nodes are greater than or equal to this value, and subsequently the transmit PHY rate of one pair of MoCA Nodes is less than this value, send {{param|BelowPhyThresholdTrap}} if {{param|PhyThresholdTrapEnable}} is {{true}}. If transmit PHY rate between one or more pairs of MoCA Nodes are less than this value, and subsequently the transmit PHY rate between all pairs of MoCA Nodes are greater than or equal to this value, send {{param|AbovePhyThresholdTrap}} if {{param|PhyThresholdTrapEnable}} is {{true}}. See {{bibref|MoCAv2.0|Section 3, Unusable Link definition}}. If transmit PHY rate between all pairs of MoCA Nodes are greater than or equal to {{param|PhyThreshold}}, and subsequently the transmit PHY rate of one pair of MoCA Node is less than {{param|PhyThreshold}}, send {{param|BelowPhyThresholdTrap}} if this value is {{true}}, do not send {{param|BelowPhyThresholdTrap}} if this value is {{false}}. If transmit PHY rate between one or more pairs of MoCA Nodes are less than {{param|PhyThreshold}}, and subsequently the transmit PHY rate between all pairs of MoCA Nodes are greater than or equal to {{param|PhyThreshold}}, send {{param|AbovePhyThresholdTrap}} if this value is {{true}}, do not send {{param|AbovePhyThresholdTrap}} if this value is {{false}}. Only one MoCA Node in the MoCA network should set {{param}} to {{true}}. If {{param}} is {{true}} and {{param|Status}} changes, then the trap {{param|StatusChangeTrap}} is sent. If {{param}} is {{true}} and {{param|NumNodes}} changes, then the trap {{param|NumNodesChangeTrap}} is sent. If transmit PHY rate between all pairs of MoCA Nodes are greater than or equal to {{param|PhyThreshold}}, and subsequently the transmit PHY rate of one pair of MoCA Nodes drops below {{param|PhyThreshold}}, send this notification if {{param|PhyThresholdTrapEnable}} is {{true}}. This parameter is a counter that is incremented whenever the event occurs. If transmit PHY rate between one or more pairs of MoCA Nodes are less than {{param|PhyThreshold}}, and subsequently the transmit PHY rate between all pairs of MoCA Nodes goes above or is equal to {{param|PhyThreshold}}, send this notification if {{param|PhyThresholdTrapEnable}} is {{true}}. This parameter is a counter that is incremented whenever the event occurs. This trap is sent when {{param|StatusChangeEnable}} is {{true}} and {{param|Status}} changes value. This parameter is a counter that is incremented whenever the event occurs. This trap is sent when {{param|NumNodesChangeEnable}} is {{true}} and {{param|NumNodes}} changes value. This parameter is a counter that is incremented whenever the event occurs. An MR Entry Node reports that the network got reset successfully (MRRST_SUCCESS Event). This parameter is a counter that is incremented whenever the event occurs. An MR Entry Node reports that the network reset did not complete successfully (MRRST_FAIL Event). This parameter is a counter that is incremented whenever the event occurs. An MR Entry Node reports that the network got reformed successfully following the MR transaction (MRNETWORK_SUCCESS Event). This parameter is a counter that is incremented whenever the event occurs. An MR Entry Node reports that the MR transaction failed, and the network did not get reformed (MRNETWORK_FAIL Event). This parameter is a counter that is incremented whenever the event occurs. When the MoCA Node is in Power State M1 or M2, indicates that the MoCA Node has received a Broadcast data MSDU, which is available at the data interface (POWER_STATEBCST_REC Event). This parameter is a counter that is incremented whenever the event occurs. When a MoCA Node is in Power State M1, indicates that it is going to move to Power State M0 due to the NCs instruction. This parameter is a counter that is incremented whenever the event occurs (POWER_STATEM0_NC Event). When the MoCA Node is in Power State M1/M2/M3, indicates that MoCA 1 Node is the NC (POWER_STATENC_1X Event). This parameter is a counter that is incremented whenever the event occurs. When the MoCA Node is in Power State M2 or M3, indicates that the network MoCA version is changed (POWER_STATENET_VER Event). This parameter is a counter that is incremented whenever the event occurs. Carries the response of the MoCA Node to a request (through POWER_STATEREQ) to transition into a desired Power State (POWER_STATERESP Event). This parameter is a counter that is incremented whenever the event occurs. When the MoCA Node is in Power State M2, indicates that a Unicast data MSDU destined to the MoCA Node is pending (POWER_STATEUCST_PEN Event). This parameter is a counter that is incremented whenever the event occurs. When a MoCA Node is in Power State M1 or M2, requests to transition to Power State M0 (POWER_STATETRNS_REQ Event). This parameter is a counter that is incremented whenever the event occurs. When the MoCA Node is in Power State M2, this reports a wakeup request from NC due to unspecified reasons (POWER_STATEWUP_UR Event). This parameter is a counter that is incremented whenever the event occurs. When {{param|LmoTrapEnable}} is enabled, reports that the MoCA Node is starting LMO (Link Maintenance Operation). This parameter is a counter that is incremented whenever the event occurs. Indicates a link failure. If the failure was an Admission or LMO failure, {{param|LinkState}} indicates when the link was dropped within the sequence. This parameter is a counter that is incremented whenever the event occurs. Used to enable {{param|ConnectedNodesChangeTrap}}. This trap is sent when {{param|ConnectedNodesChangeTrapEn}} is {{true}} and {{param|ConnectedNodesInfo}} changes value. This parameter is a counter that is incremented whenever the event occurs. Used to enable {{param|MgntEntityNetwIePayloadRecTrap}}. This trap is sent when {{param|MgntEntityNetwIePayloadRecTrapEn}} is {{true}} and {{param|MgntEntityNetIePayloadRx}} changes value. This parameter is a counter that is incremented whenever the event occurs. Used to enable the MPS-related traps: {{param|MpsInitScanRecTrap}}, {{param|MpsPairFailTrap}}, and {{param|MpsPrivacyChangedTrap}}. This trap is sent when {{param|MpsTrapEn}} is {{true}} and {{param|MpsInitScanPayload}} changes value. This parameter is a counter that is incremented whenever the event occurs. This trap is sent when {{param|MpsTrapEn}} is {{true}}, indicates a MPS pairing failure. This parameter is a counter that is incremented whenever the event occurs. This trap is sent when {{param|MpsTrapEn}} is {{true}}, indicates that the Node's privacy settings (PRIVACYEN and/or PSWD) have been changed by MPS. This parameter is a counter that is incremented whenever the event occurs. Used to enable {{param|NcPrivacySupportedRecTrap}}. This trap is sent when {{param|NcPrivSupportedRecTrapEn}} is {{true}} and {{param|PrivacyNc}} changes value. This parameter is a counter that is incremented whenever the event occurs. Used to enable {{param|NetworkNameRecTrap}}. This trap is sent when {{param|NetworkNameRecTrapEn}} is {{true}} and {{param|NetworkNamePayload}} changes value. This parameter is a counter that is incremented whenever the event occurs. This trap is sent when {{param|NodeDropTrapEn}} is {{true}}, indicates that the Node drops from the network due to admission failure. This parameter is a counter that is incremented whenever the event occurs. Used to enable {{param|NodeDropAdmFailureTrap}}, {{param|NodeDropNcTrap}}, {{param|NodeDropMpsTriggeredTrap}}, and {{param|NodeDropNcChgTrap}}. This trap is sent when {{param|NodeDropTrapEn}} is {{true}}, indicates that the Node is dropped by the NC as indicated in the NODE_BITMASK and LOW_POWER_NODE_BITMASK. This parameter is a counter that is incremented whenever the event occurs. This trap is sent when {{param|NodeDropTrapEn}} is {{true}}, indicates that MPS is locally triggered when the Node is un-Paired. This parameter is a counter that is incremented whenever the event occurs. This trap is sent when {{param|NodeDropTrapEn}} is {{true}}}, indicates that there is a NC change when the Node is Non-Secured Admitted Node. This parameter is a counter that is incremented whenever the event occurs. Parameters to control ACA (Alternate Channel Assessment) for the MoCA interface. Notifications for bandwidth threshold in the MoCA network. The compliance statement for the mandatory groups.