The value MUST be the value of the {{param: non-existent #.XMPP.Connection.{i}.JabberID}} contained in the {{object: non-existent #.XMPP.Connection}} instance referenced by the ConnReqXMPPConnection parameter.

If the ConnReqXMPPConnection parameter is empty or the {{object: non-existent #.XMPP.Connection}} instance being reference is disabled, then this value will be empty.

If the {{object: non-existent #.XMPP.Connection}} instance being referenced by the ConnReqXMPPConnection parameter is lost ({{param: non-existent #.XMPP.Connection.{i}.Status}} parameter changes from Enabled to some other value), then the value of this parameter MUST remain unchanged until the connection can be reestablished and a new {{param: non-existent #.XMPP.Connection.{i}.JabberID}} can be established. If the new {{param: non-existent #.XMPP.Connection.{i}.JabberID}} is identical to the existing value, then the value of this parameter MUST NOT be altered and a VALUE CHANGE event MUST NOT be generated.

Active Notification MUST by default be enabled for this parameter.

Comma-separated list (maximum number of characters 1024) of strings. Each list item MUST be the Path Name of a row in the Hosts.Host. table. If the referenced object is deleted, the corresponding item MUST be removed from the list. References all the {{object: non-existent ##.Hosts.Host}} table entries, whether active or inactive, that correspond to this physical LAN device. There can be multiple such entries if the device has more than one network interface.

For example: Device.Hosts.Host.1,Device.Hosts.Host.5

Comma-separated list of strings. Each list item MUST be the Path Name of an object discovered using one or more protocols listed in DiscoveryProtocol|ignore, or an empty string.

For objects discovered by the UPnP discovery protocol, the DiscoveryProtocolReference would contain items that are references to instances of the following:

• {{object: non-existent ##.UPnP.Discovery.RootDevice}}
• {{object: non-existent ##.UPnP.Discovery.Device}}
• {{object: non-existent ##.UPnP.Discovery.Service}}

For objects discovered by the ETSI-M2M discovery protocol, the DiscoveryProtocolReference would contain items that are references to instances of ETSIM2M.SCL.{i}.AreaNwkDeviceInfoInstance.

Comma-separated list of strings. Each list item MUST be the Path Name of an object discovered using one or more protocols listed in DiscoveryProtocol|ignore, or an empty string.

For objects discovered by the UPnP discovery protocol, the DiscoveryProtocolReference would contain items that are references to instances of the following:

• {{object: non-existent ##.UPnP.Discovery.RootDevice}}
• {{object: non-existent ##.UPnP.Discovery.Device}}
• {{object: non-existent ##.UPnP.Discovery.Service}}

For objects discovered by the ETSI-M2M discovery protocol, the DiscoveryProtocolReference would contain items that are references to instances of ETSIM2M.SCL.{i}.AreaNwkDeviceInfoInstance.

A string identifying the version of the firmware image represented by this FirmwareImage. Whenever this firmware image is active (ie, the device has booted this firmware image), the value of the {{param: non-existent #.SoftwareVersion}} parameter MUST be the same as the value contained in this parameter.

To allow version comparisons, this element SHOULD be in the form of dot-delimited integers, where each successive integer represents a more minor category of variation. For example, 3.0.21 where the components mean: Major.Minor.Build.

The value of Version is an empty string if Status is anything other than Available, InstallationFailed, or ActivationFailed.

StatusReflects the global time synchronisation status of Time support on the CPE. Enumeration of:

• Disabled (

Indicates that the CPE’s time client services are disabled.

)

• Unsynchronized (

Indicates that the CPE’s absolute time has not yet been set by any of the configured time clients.

)

• Synchronized (

Indicates that the CPE has acquired accurate absolute time; its current time is accurate. One or more time client was able to configure the time of the CPE.

)

• Error_FailedToSynchronize (

This enumeration was DEPRECATED in 2.16 due to the introduction of Client.

)

• Error (

MAY be used by the CPE to indicate a locally defined error condition. None of the configured Time clients were able to synchronize the time.

, OPTIONAL)

Present only if the CPE provides a password-protected LAN-side user interface and supports LAN-side Auto-Configuration.

Indicates whether or not a password to protect the local user interface of the CPE MAY be selected by the user directly (i.e. {{param: non-existent #.Users.User.{i}.Password}}), or MUST be equal to the password used by the LAN-side Auto-Configuration protocol (i.e. {{param: non-existent #.LANConfigSecurity.ConfigPassword}}).

Present only if the CPE provides a password-protected LAN-side user interface and supports LAN-side Auto-Configuration.

When set to true, resets {{param: non-existent #.LANConfigSecurity.ConfigPassword}} to its factory value.

The server the CPE can check to see if an update is available for direct download to it.

This MUST NOT be used by the CPE if the {{param: non-existent #.ManagementServer.UpgradesManaged}} parameter is true.

The server where a user can check via a web browser if an update is available for download to a PC.

This MUST NOT be used by the CPE if the {{param: non-existent #.ManagementServer.UpgradesManaged}} parameter is true.

Indicates the link encapsulation standard that the Channel instance is using for the connection. Enumeration of:

• G.992.3_Annex_K_ATM
• G.992.3_Annex_K_PTM
• G.993.2_Annex_K_ATM
• G.993.2_Annex_K_PTM

When ATM encapsulation is identified then an upper-layer {{object: non-existent ##.ATM.Link}} interface MUST be used.

When PTM encapsulation is identified then an upper-layer {{object: non-existent ##.PTM.Link}} interface MUST be used.

Loop termination indicator. Enumeration of:

• Open
• Short
• Powered on DSLAM/DPU (

This enumeration was OBSOLETED in 2.14 because it’s been removed from the ITU-T Recommendation.

This enumeration was DELETED in 2.16.

)

• Powered on CPE
• Unknown

This parameter is defined as LOOP-TERM in ITU-T Recommendation [Clause B.1.1.1/G.996.2].

This parameter reports the electrical length expressed in 0.1dB, that would have been sent from the FTU-O to the FTU-R if the electrical length was not forced by the DPU-MIB. If the electrical length is not forced by the DPU-MIB, then this object reports the final electrical length, as determined by the FTU-O (see clause 7.3.1.4.2.1/[G.9701]) and conveyed in the O-UPDATE initialization message (see clause 12.3.3.2.4/[G.9701]).

Note: See clause 7.10.4.1 in ITU-T Recommendation [G.997.2].

Allows the Controller to change the USIM PIN used for SIM card activation.

When read, this parameter returns an empty string, regardless of the actual value.

Password used to authenticate the CPE when making a connection to the Access Point.

When read, this parameter returns an empty string, regardless of the actual value.

[docsIfDownChannelFrequency/1.3.6.1.2.1.10.127.1.1.1.1.2] The center of the downstream frequency associated with this channel. This object will return the current tuner frequency.frequency, measured in Hz.

See [Section 6.3.3/CM-SP-RFIv2.0].

[docsIfDownChannelWidth/1.3.6.1.2.1.10.127.1.1.1.1.3] The bandwidth in Hz of this downstream channel. Most implementations are expected to support a channel width of 6 MHz (North America) and/or 8 MHz (Europe).

See [Table 6-17/CM-SP-RFIv2.0].

[docsIfSigQSignalNoise/1.3.6.1.2.1.10.127.1.1.4.1.5] [TenthdB] Signal/Noise ratio as perceived for this channel. Describes the Signal/Noise of the downstream channel.channel, measured in TenthdB.

See [Tables 4-1 and 4-2/CM-SP-RFIv2.0].

[docsIfSigQMicroreflections/1.3.6.1.2.1.10.127.1.1.4.1.6] Microreflections, including in-channel response as perceived on this interface, measured in -dBc (i.e., dBc below the signal level.level). This object is not assumed to return an absolutely accurate value, but it gives a rough indication of microreflections received on this interface. It is up to the implementer to provide information as accurately as possible.

See [Tables 4-1 and 4-2/CM-SP-RFIv2.0].

[docsIf3SignalQualityExtRxMER/1.3.6.1.4.1.4491.2.1.20.1.24.1.1] [TenthdB] RxMER provides an in-channel received Modulation Error Ratio (MER).(MER), measured in TenthdB. RxMER is defined as an estimate, provided by the demodulator, of the ratio: (average constellation energy with equally likely symbols) / (average squared magnitude of error vector)

RxMER is measured just prior to FEC (trellis/Reed-Solomon) decoding. RxMER includes the effects of the HFC channel as well as implementation effects of the modulator and demodulator. Error vector estimation may vary among demodulator implementations. In the case of S-CDMA mode, RxMER is measured on the de-spread signal.

[docsIfUpChannelFrequency/1.3.6.1.2.1.10.127.1.1.2.1.2] The center of the frequency band associated with this upstream interface. This object returns 0 if the frequency is undefined or unknown. Minimum permitted upstream frequency is 5,000,000 HzHz for current technology.

See [Table 4-2/CM-SP-RFIv2.0].

[docsIfUpChannelWidth/1.3.6.1.2.1.10.127.1.1.2.1.3] The bandwidth in Hz of this upstream interface. This object returns 0 if the interface width is undefined or unknown. Minimum permitted interface width is currently 200,000 Hz.Hz.

See [Table 6-5/CM-SP-RFIv2.0].

[docsIfUpChannelSlotSize/1.3.6.1.2.1.10.127.1.1.2.1.5] Applicable to TDMA and ATDMA channel types only. The number of 6.25 microsecond6.25 microsecond ticks in each upstream mini-slot. Returns zero if the value is undefined or unknown or in case of an SCDMA channel.

See [Section 8.1.2.4/CM-SP-RFIv2.0].

[docsIf3CmSpectrumAnalysisCtrlCmdInactivityTimeout/1.3.6.1.4.1.4491.2.1.20.1.34.2] This attribute controls the length of time (in seconds) after the last spectrum analysis measurement before the feature is automatically disabled. If set to a value of 0, the feature will remain enabled until it is explicitly disabled.

See [CM-SP-CM-OSSIv3.1], Proactive Network Maintenance Information Model.

The factory default value MUST be 300.

[docsIf3CmSpectrumAnalysisCtrlCmdFirstSegmentCenterFrequency/1.3.6.1.4.1.4491.2.1.20.1.34.3] This attribute controls the center frequency (in Hz) of the first segment for the spectrum analysis measurement. The frequency bins for this segment lie symmetrically to the left and right of this center frequency.

If the number of bins in a segment is odd, the segment center frequency lies directly on the center bin.

If the number of bins in a segment is even, the segment center frequency lies halfway between two bins.

Changing the value of this attribute may result in changes to the Result table. Note that if this parameter is set to an invalid value, the device may return an error, or may adjust the value of the parameter to the closest valid value.

See [CM-SP-CM-OSSIv3.1], Proactive Network Maintenance Information Model.

The factory default value MUST be 93000000.

[docsIf3CmSpectrumAnalysisCtrlCmdLastSegmentCenterFrequency/1.3.6.1.4.1.4491.2.1.20.1.34.4] This attribute controls the center frequency (in Hz) of the last segment of the spectrum analysis measurement.

The frequency bins for this segment lie symmetrically to the left and right of this center frequency. If the number of bins in a segment is odd, the segment center frequency lies directly on the center bin. If the number of bins in a segment is even, the segment center frequency lies halfway between two bins.

The value of the LastSegmentCenterFrequency should be equal to the FirstSegmentCenterFrequency plus and integer number of segment spans as determined by the SegmentFrequencySpan.

Changing the value of this attribute may result in changes to the Result table.

Note that if this parameter is set to an invalid value, the device may return an error, or may adjust the value of the parameter to the closest valid value.

See [CM-SP-CM-OSSIv3.1], Proactive Network Maintenance Information Model.

The factory default value MUST be 993000000.

[docsIf3CmSpectrumAnalysisCtrlCmdSegmentFrequencySpan/1.3.6.1.4.1.4491.2.1.20.1.34.5] This attribute controls the frequency span (in Hz) of each segment (instance) of the Result.{i} table.

If set to a value of 0, then a default span will be chosen based on the hardware capabilities of the device. Segments are contiguous from the FirstSegmentCenterFrequency to the LastSegmentCenterFrequency and the center frequency for each successive segment is incremented by the SegmentFrequencySpan. The number of segments is (LastSegmentCenterFrequency - FirstSegmentCenterFrequency)/SegmentFrequencySpan + 1. A segment is equivalent to an instance in the Result table. The chosen SegmentFrequencySpan affects the number of entries in Result table. A more granular SegmentFrequencySpan may adversely affect the amount of time needed to query the table entries in addition to possibly increasing the acquisition time.

Changing the value of this attribute may result in changes to Result table.

Note that if this parameter is set to an invalid value, the device may return an error, or may adjust the value of the parameter to the closest valid value.

See [CM-SP-CM-OSSIv3.1], Proactive Network Maintenance Information Model.

The factory default value MUST be 7500000.

[docsIf3CmSpectrumAnalysisCtrlCmdEquivalentNoiseBandwidth/1.3.6.1.4.1.4491.2.1.20.1.34.7] This parameter allows the user to request an equivalent noise bandwidth (measured in hundredthsbin) for the resolution bandwidth filter used in the spectrum analysis. This corresponds to the spectral width of the window function used when performing a discrete Fourier transform for the analysis.

The window function which corresponds to a value written to this parameter may be obtained by reading the value of WindowFunction.

If an unsupported value is requested, the device may return an error, or choose the closest valid value to the one which is requested. If the closest value is chosen, then a subsequent read of this parameter will return the actual value which is in use.

See [CM-SP-CM-OSSIv3.1], Proactive Network Maintenance Information Model.

The factory default value MUST be 150.

[MACAddress] The MAC Address of the interface.

Note: This is not necessarily the same as the Ethernet header source or destination MAC address, which is associated with the IP interface and is modeled via the {{param: non-existent ##.Ethernet.Link.{i}.MACAddress}} parameter.

[MACAddress] The unique manufacturer-assigned Ethernet hardware address of the interface, also referred to as burned-in MAC address.

Note: This is not necessarily the same as the MAC address used for higher-level protocols, which is modeled via the {{param: non-existent #.Link.{i}.MACAddress}} parameter. Its main purpose is the identification of a specific Ethernet interface; the information can also can be used to perform Wake on LAN.

Enables or disables priority tagging on this Ethernet Link.

When true, egress frames leaving this interface will be priority tagged with the frame’s associated priority value, which will either be derived directly from the ingress frame or else set via {{param: non-existent ##.QoS.Classification.{i}.EthernetPriorityMark}} or {{param: non-existent ##.QoS.Classification.{i}.InnerEthernetPriorityMark}}.

When false, egress frames leaving this interface will be untagged.

The parameter does not affect reception of ingress frames.

[MACAddress] The MAC Address of the interface.

Note: This is not necessarily the same as the Ethernet header source or destination MAC address, which is associated with the IP interface and is modeled via the {{param: non-existent ##.Ethernet.Link.{i}.MACAddress}} parameter.

[MACAddress] The MAC Address of the interface.

Note: This is not necessarily the same as the Ethernet header source or destination MAC address, which is associated with the IP interface and is modeled via the {{param: non-existent ##.Ethernet.Link.{i}.MACAddress}} parameter.

[MACAddress] The MAC Address of the interface.

Note: This is not necessarily the same as the Ethernet header source or destination MAC address, which is associated with the IP interface and is modeled via the {{param: non-existent ##.Ethernet.Link.{i}.MACAddress}} parameter.

MoCA Password. The value consists of numeric characters (0-9). Possible patterns:

• \d+

This parameter is based on mocaIfPassword from [MOCA11-MIB].

When read, this parameter returns an empty string, regardless of the actual value.

[MACAddress] The MAC Address of the interface, denoted as node MAC address or REGID in [G.9961].

Note: This is not necessarily the same as the Ethernet header source or destination MAC address, which is associated with the IP interface and is modeled via the {{param: non-existent ##.Ethernet.Link.{i}.MACAddress}} parameter.

[MACAddress] The MAC Address of the interface.

Note: This is not necessarily the same as the Ethernet header source or destination MAC address, which is associated with the IP interface and is modeled via the {{param: non-existent ##.Ethernet.Link.{i}.MACAddress}} parameter.

The network password of the device. This is a human readable ASCII string that is hashed per the HomePlug specification to generate the Network Membership Key (NMK). Note that care needs to be taken when setting this parameter as it might prohibit communication with other adapters or equipment connected via the powerline network.

When read, this parameter returns an empty string, regardless of the actual value.

[MACAddress] The MAC Address of the interface.

Note: This is not necessarily the same as the Ethernet header source or destination MAC address, which is associated with the IP interface and is modeled via the {{param: non-existent ##.Ethernet.Link.{i}.MACAddress}} parameter.

Encryption key for secure PLC communications.

This a human readable string used by the system to generate the encryption key to encrypt communications in powerline. It takes non extended ASCII characters (i.e. printable 7-bit ASCII character codes 32-126, which includes SPACE but excludes TAB, LF and CR). For example: bvjPekZiYUf9kjNKJASkgJ09adfoP01Fjvgd

When read, this parameter returns an empty string, regardless of the actual value.

Comma-separated list of strings. The band(s) (GHz) for which this SSID applies. Each list item is an enumeration of:

• All (Applies to all bands)
• 2.4 (2.4 GHz band)
• 5 (The entire 5 GHz band)
• 6 (The entire 6 GHz band)
• 5_UNII_1 (5 GHz UNII-1 band, 5.15 to 5.25 GHz)
• 5_UNII_2 (5 GHz UNII-2 band, 5.25 to 5.725 GHz)
• 5_UNII_3 (5 GHz UNII-3 band, 5.725 to 5.85 GHz)
• 5_UNII_4 (5 GHz UNII-4 band, 5.85 to 5.925 GHz)
• 6_UNII_5 (6 GHz UNII-5 band, 5.925 to 6.425 GHz)
• 6_UNII_6 (6 GHz UNII-6 band, 6.425 to 6.525 GHz)
• 6_UNII_7 (6 GHz UNII-7 band, 6.525 to 6.875 GHz)
• 6_UNII_8 (6 GHz UNII-8 band, 6.875 to 7.125 GHz)

Identifier of the manufacturer of the device.

If the instance of this Device is the same as Device., then this parameter is the same as Device.DeviceInfo.Manufacturer.

Identifier of the particular Access Point device that is unique for the indicated model and manufacturer.

This value MUST remain fixed over the lifetime of the device, including across firmware updates.

If the instance of this Device is the same as Device., then this parameter is the same as Device.DeviceInfo.SerialNumber.

Identifier of the manufacturer model to help the user more easily identify a particular piece of equipment.

If the instance of this Device is the same as Device., then this parameter is the same as Device.DeviceInfo.ModelName.

Identifier of the software version currently installed in the Access Point device (i.e. version of the overall firmware).

If the instance of this Device is the same as Device., then this parameter is the same as Device.DeviceInfo.SoftwareVersion.

Identifier of the execution environment (operating system) in the device. This parameter can be an entry in the table {{object: non-existent ####.SoftwareModules.ExecEnv.}}

If the instance of this Device is the same as Device., then this parameter is the same as DeviceDevice.SoftwareModules.ExecEnv.{i}..

Two-character country code in which the Multi-AP Agent is operating according to [ISO3166-1]. The characters are encoded as UTF-8.

If the instance of this DataElements is the same as Device.WiFi.Radio.{i}., then this parameter is the same as Device.WiFi.Radio.{i}.RegulatoryDomain.

Onboarding protocols supported;

0: 1905 Device.Device Provisioning Protocol as defined in the EasyMesh [EasyMesh] 1905 Layer Security Capability TLV.

The Operating Class per [Table E-4/802.11-2020].

Note that the operating class identifies the band and channel width. This changed from readOnly to readWrite in version 2.15.

Organizationally unique identifier of the Access Point device manufacturer. Represented as a six hexadecimal-digit value using all upper-case letters and including any leading zeros. Possible patterns:

• [0-9A-F]{6}

The value MUST be a valid OUI as defined in [OUI].

This value MUST remain fixed over the lifetime of the device, including across firmware updates.

If the instance of this MultiAPDevice is the same as Device., then this parameter is the same as Device.DeviceInfo.ManufacturerOUI.

Indicates whether this radio is enabled or disabled.

If the instance of this Radio is the same as Device.WiFi.Radio.{i}., then this parameter is the same as Device.WiFi.Radio.{i}.Enable.

An indicator of the average radio noise plus interference power measured for the primary operating channel.

Encoded as defined for ANPI in [Section 11.10.9.4/802.11-2020].

If the instance of this Radio is the same as Device.WiFi.Radio.{i}., then this parameter is the same as Device.WiFi.Radio.{i}.Stats.Noise.

Associated Wi-Fi6 STA Status Inclusion Policy.

true: include Associated Wi-Fi6 STA Status TLV in AP Metrics Response.

false: do not include Associated Wi-Fi6 STA Status TLV [3] in AP Metrics Response.

The Operating Class per [Table E-4/802.11-2020] For 2.4GHz and 5GHz bands, only 20MHz Operating Classes are valid..

Note that the operating class identifies the band and channel width.

The Operating Class per [Table E-4/802.11-2020] For 2.4GHz and 5GHz bands, only 20MHz Operating Classes are valid..

Note that the operating class identifies the band and channel width.

[MACAddress] The MAC Address of the logical BSS (BSSID).

If the instance of this BSS is the same as Device.WiFi.SSID.{i}., then this parameter is the same as Device.WiFi.SSID.{i}.BSSID.

The SSID in use for this BSS.

If the instance of this BSS is the same as Device.WiFi.SSID.{i}., then this parameter is the same as Device.WiFi.SSID.{i}.SSID.

Whether the BSSID is currently enabled (beaconing frames are being sent) or disabled.

If the instance of this BSS is the same as Device.WiFi.SSID.{i}., then this parameter is the same as Device.WiFi.SSID.{i}.Enable.

Time in seconds since the last change to the Enabled value.

If the instance of this BSS is the same as Device.WiFi.SSID.{i}., then this parameter is the same as Device.WiFi.SSID.{i}.LastChange.

The descriptor element. One of:

MSCS descriptor element (as described in [Section 9.4.2.243/802.11-2020], or

SCS descriptor element (as described in [Section 9.4.2.121/802.11-2020], or

QoS Management DSCP policy element (as described in **{{bibref: non-existent {{inserted: unexpected argument Section 9.4.2.94 after: 802.11-2020}} and **{{bibref: non-existent }}RFC8325}}).

[MACAddress] The MAC address of an associated device.

If the instance of this STA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}, then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.MACAddress.

The data transmit rate in kbps that was most recently used for transmission of data from the access point to the associated device.

If the instance of this STA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}, then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.LastDataDownlinkRate.

The data transmit rate in kbps that was most recently used for transmission of data from the associated device to the access point.

If the instance of this STA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}, then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.LastDataUplinkRate.

An indicator of radio signal strength of the uplink from the associated STA to the access point - measured in dBm. RCPI thresholdis (encodedencoded per [Table 9-176/802.11-2020]},, and described in [Section 10.3.1/EasyMesh]). Reserved: 221 - 255.

NOTE: The underlying WFA specification is in the process of being reviewed for possible clarification. Please refer to that specification for more details.

If the instance of this STA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}, then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.SignalStrength.

[StatsCounter64] The total number of bytes transmitted to the Associated Device.

If the instance of this STA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}, then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.BytesSent.

[StatsCounter64] The total number of bytes received from the Associated Device.

If the instance of this STA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}, then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.BytesReceived.

[StatsCounter64] The total number of packets transmitted to the Associated Device.

If the instance of this STA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}, then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.PacketsSent.

[StatsCounter64] The total number of packets received from the Associated Device.

If the instance of this STA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}, then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.PacketsReceived.

[StatsCounter64] The total number of outbound packets that could not be transmitted because of errors. These might be due to the number of retransmissions exceeding the retry limit, or from other causes.

If the instance of this STA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}, then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.ErrorsSent.

[StatsCounter64] The total number of inbound packets that contained errors preventing them from being delivered to a higher-layer protocol.

If the instance of this STA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}, then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.ErrorsReceived.

[StatsCounter64] The total number of transmitted packets which were retransmissions. Two retransmissions of the same packet results in this counter incrementing by two.

If the instance of this STA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}, then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.RetransCount.

Date and time in UTC when the device was associated.

If the instance of this MultiAPSTA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}., then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.AssociationTime.

An indicator of the average radio noise plus interference power measured on the uplink from the Associated Device (STA) to the Access Point (AP).

Encoded as defined for ANPI in [Section 11.10.9.4/802.11-2020].

If the instance of this MultiAPSTA is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}., then this parameter is the same as Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Noise.

An indicator of radio signal strength (RCPI) of the uplink from the Non-AP STA - measured in dBm. (RCPI thresholdRCPI is encoded per [Table 9-176/802.11-2020], and described in [Section 10.3.2/EasyMesh]).. Reserved: 221 - 255.

NOTE: The underlying WFA specification is in the process of being reviewed for possible clarification. Please refer to that specification for more details.

Enables or disables the radio.

This parameter is based on ifAdminStatus from [RFC2863].

If the instance of this Radio is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}, then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.Enabled.

Comma-separated list of strings. List items indicate the frequency bands at which the radio can operate.

Each list item is an enumeration of:

• 2.4GHz
• 5GHz
• 6GHz (Added in 2.16)

Comma-separated list of strings. List items indicate which IEEE 802.11 standards this Radio instance can support simultaneously, in the frequency band specified by OperatingFrequencyBand. Each list item is an enumeration of:

• a ([802.11a-1999])
• b ([802.11b-1999])
• g ([802.11g-2003])
• n ([802.11n-2009])
• ac ([802.11ac-2013])
• ax ([802.11ax])

Each value indicates support for the indicated standard.

If OperatingFrequencyBand is set to 2.4GHz, only values b, g, n, ax are allowed.

If OperatingFrequencyBand is set to 5GHz, only values a, n, ac, ax are allowed.

If OperatingFrequencyBand is set to 6GHz, only value ax is allowed.

Each list item MUST be a member of the list reported by the SupportedStandards parameter. Comma-separated list of strings. List items indicate which IEEE 802.11 standard this Radio instance is configured for.

Each value indicates support for the indicated standard.

If OperatingFrequencyBand is set to 2.4GHz, only values b, g, n, ax are allowed.

If OperatingFrequencyBand is set to 5GHz, only values a, n, ac, ax are allowed.

If OperatingFrequencyBand is set to 6GHz, only value ax is allowed.

For example, a value of “g,b” (or “b,g” - order is not important) means that the 802.11g standard [802.11g-2003] is used with a backwards-compatible mode for 802.11b [802.11b-1999]. A value of “g” means that only the 802.11g standard can be used.

The current radio channel used by the connection. To request automatic channel selection, set AutoChannelEnable to true.

Whenever AutoChannelEnable is true, the value of the Channel parameter MUST be the channel selected by the automatic channel selection procedure.

For channels in “wide mode” (802.11n where a 40MHz channel bandwidth is used), this parameter is used for Primary Channel only. The secondary or extension channel information is available through ExtensionChannel.

Note: Valid Channel values depend on the OperatingFrequencyBand value specified and the RegulatoryDomain.

If the instance of this Radio is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.CurrentOperatingClassProfile.{i}.Channel.

This radio’s WiFi firmware version.

If the instance of this Device is the same as Device.WiFi.DataElements.Network.Device.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.SoftwareVersion.

Indicates the current transmit power level as a percentage of full power. The value MUST be one of the values reported by the TransmitPowerSupported parameter. A value of -1 indicates auto mode (automatic decision by CPE).

If the instance of this Radio is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.CurrentOperatingClassProfile.{i}.TxPower.

The 802.11d Regulatory Domain. First two octets are [ISO3166-1] two-character country code. The third octet is either “ “ (all environments), “O” (outside) or “I” (inside).

If the instance of this Device is the same as Device.WiFi.DataElements.Network.Device.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.CountryCode.

Possible patterns:

• [A-Z][A-Z][ OI]

Comma-separated list of strings. DataMaximum radio data transmit rates in Mbps for unicast frames at which the access point will permit a station to connect (a subsetsuperset of {{param: non-existent BasicDataTransmitRates}}). Given the valuesvalue of BasicDataTransmitRates and OperationalDataTransmitRates from the examplesexample above, SupportedDataTransmitRates might be “1,2,5.5”,“1,2,5.5,11”, indicating that theunicast APframes willcan onlyadditionally permitbe connectionstransmitted at 1 Mbps, 25.5 Mbps and 5.5 Mbps, even though it could theoretically accept connections at 11 Mbps.

SupportedDataTransmitRates indicates equipment capability. This radio is capable of supporting these data rates.

Comma-separated list of strings. Maximum access point dataData transmit rates in Mbps for unicast frames at which the radio will permit operation with any associated station (a supersetsubset of {{param: non-existent SupportedDataTransmitRates}}). Given the valuevalues of BasicDataTransmitRates and SupportedDataTransmitRates from the exampleexamples above, OperationalDataTransmitRates might be “1,2,5.5,11”,“1,2,5.5”, indicating that unicastthe framesradio canwill additionallyonly bepermit transmittedoperation at 5.51 Mbps, 2 Mbps and 5.5 Mbps, even though it could theoretically operate at 11 Mbps.

This radio is limited to allowing operation only at these data rates. Note: Setting OperationalDataTransmitRates can’t increase the set of possible data rates but could narrow them.

[DiagnosticsState] Indicates the availability of diagnostics data. Enumeration of:

Enumeration of:

• None (READONLY)
• Requested
• Canceled (OPTIONAL)
• Complete (READONLY)
• Error (READONLY, OPTIONAL)
• Completed (

This enumeration was DEPRECATED in 2.13 because it’s a typo for Complete.

This enumeration was OBSOLETED in 2.16.

, READONLY)

If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed values are Requested and Canceled. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set, and any errors or inconsistencies in the test parameters MUST be detected, either prior to or at the same time as (in the same SetParameterValues) setting this parameter to Requested.

When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic test.

When the test is completed, the value of this parameter MUST be either Complete (if the test completed successfully), or one of the Error values listed above.

If the value of this parameter is anything other than Complete, the values of the results parameters for this test are indeterminate.

When the diagnostic initiated by the ACS is completed (successfully or not), but not if it is canceled for any reason, the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code 8 DIAGNOSTICS COMPLETE in the Inform message.

After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None.

Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None.

While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None.

While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

While the test is in progress, setting this parameter to Canceled MUST result in the test being canceled and the value of this parameter being set to None. If the CPE does not support the Canceled value, it MUST return a SPV error with “Invalid Parameter value” (9007) to the ACS instead.

Enumeration of:

• None (READONLY)
• Requested
• Canceled (OPTIONAL)
• Complete (READONLY)
• Error (READONLY, OPTIONAL)
• Completed (

This enumeration was DEPRECATED in 2.13 because it’s a typo for Complete.

This enumeration was OBSOLETED in 2.16.

, READONLY)

The type of encryption the neighboring WiFi SSID advertises.

The WEP value indicates either WEP-64 or WEP-128.

The WPA value is the same as WPA-Personal.

The WPA2 value is the same as WPA2-Personal.

The WPA-WPA2 value is the same as WPA-WPA2-Personal.

The WPA3-SAE value is the same as WPA3-Personal.

The WPA2-PSK-WPA3-SAE value is the same as WPA3-Personal-Transition.

Enumeration of:

• None
• WEP
• WPA
• WPA2
• WPA-WPA2
• WPA-Enterprise
• WPA2-Enterprise
• WPA-WPA2-Enterprise
• WPA3-SAE
• WPA2-PSK-WPA3-SAE
• WPA3-Enterprise
• OWE (Added in 2.16)

Indicates the frequency band at which the radio this SSID instance is operating.

Enumeration of:

• 2.4GHz
• 5GHz
• 6GHz (Added in 2.16)

Comma-separated list of strings. List items indicate which IEEE 802.11 standards this Result instance can support simultaneously, in the frequency band specified by OperatingFrequencyBand. Each list item is an enumeration of:

• a ([802.11a-1999])
• b ([802.11b-1999])
• g ([802.11g-2003])
• n ([802.11n-2009])
• ac ([802.11ac-2013])
• ax ([802.11ax])

Each value indicates support for the indicated standard.

If OperatingFrequencyBand is set to 2.4GHz, only values b, g, n, ax are allowed.

If OperatingFrequencyBand is set to 5GHz, only values a, n, ac, ax are allowed.

If OperatingFrequencyBand is set to 6GHz, only value ax is allowed.

Each list item MUST be a member of the list reported by the SupportedStandards parameter. Comma-separated list of strings. List items indicate which IEEE 802.11 standard that is detected for this Result.

Each value indicates support for the indicated standard.

If OperatingFrequencyBand is set to 2.4GHz, only values b, g, n, ax are allowed.

If OperatingFrequencyBand is set to 5GHz, only values a, n, ac, ax are allowed.

If OperatingFrequencyBand is set to 6GHz, only value ax is allowed.

For example, a value of “g,b” (or “b,g” - order is not important) means that the 802.11g standard [802.11g-2003] is used with a backwards-compatible mode for 802.11b [802.11b-1999]. A value of “g” means that only the 802.11g standard can be used.

An indicator of average noise strength received at this radio, measured in dBm. This measurement of non-IEEE 802.11 noise power is made by sampling the channel when virtual carrier sense indicates idle and this radio is neither transmitting nor receiving a frame.

If the instance of this Stats is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.Noise.

Enables or disables the SSID entry.

This parameter is based on ifAdminStatus from [RFC2863].

If the instance of this SSID is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.Enabled.

The accumulated time in seconds since the SSID entered its current operational state.

If the instance of this SSID is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.LastChange.

Active Notification requests for this parameter MAY be denied.

[MACAddress] The Basic Service Set ID.

This is the MAC address of the access point, which can either be local (when this instance models an access point SSID) or remote (when this instance models an end point SSID).

If the instance of this SSID is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.BSSID.

[MACAddress] The MAC address of this interface.

If this instance models an access point SSID, MACAddress is the same as BSSID.

Note: This is not necessarily the same as the Ethernet header source or destination MAC address, which is associated with the IP interface and is modeled via the {{param: non-existent ##.Ethernet.Link.{i}.MACAddress}} parameter.

The current service set identifier in use by the connection. The SSID is an identifier that is attached to packets sent over the wireless LAN that functions as an ID for joining a particular radio network (BSS).

If the instance of this SSID is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.SSID.

Comma-separated list of strings. Indicates which security modes this AccessPoint instance is capable of supporting.

The WPA3-Personal value is the same as WPA3-SAE.

The WPA3-Personal-Transition value is the same as WPA2-PSK-WPA3-SAE.

Each list item is an enumeration of:

• None
• WEP-64
• WEP-128
• WPA-Personal
• WPA2-Personal
• WPA3-Personal
• WPA-WPA2-Personal
• WPA3-Personal-Transition
• WPA-Enterprise
• WPA2-Enterprise
• WPA3-Enterprise
• WPA-WPA2-Enterprise
• OWE (Added in 2.16)

A WEP key expressed as a hexadecimal string.

WEPKey is used only if ModeEnabled is set to WEP-64 or WEP-128.

A 5 byte WEPKey corresponds to security mode WEP-64 and a 13 byte WEPKey corresponds to security mode WEP-128.

When read, this parameter returns an empty string, regardless of the actual value.

A literal PreSharedKey (PSK) expressed as a hexadecimal string.

PreSharedKey is only used if ModeEnabled is set to WPA-Personal or WPA2-Personal or WPA-WPA2-Personal.

If KeyPassphrase is written, then PreSharedKey is immediately generated. The Controller SHOULD NOT set both the KeyPassphrase and the PreSharedKey directly (the result of doing this is undefined).

When read, this parameter returns an empty string, regardless of the actual value.

A passphrase from which the PreSharedKey is to be generated, for WPA-Personal or WPA2-Personal or WPA-WPA2-Personal security modes.

If KeyPassphrase is written, then PreSharedKey for WPA2 is immediately generated. The Controller SHOULD NOT set both the KeyPassphrase and the PreSharedKey directly (the result of doing this is undefined). The key is generated as specified by WPA, which uses PBKDF2 from PKCS #5: Password-based Cryptography Specification Version 2.0 ([RFC2898]).

When read, this parameter returns an empty string, regardless of the actual value.

A passphrase for WPA3-Personal or WPA3-Personal-Transition security modes.

NOTE: this parameter is for WPA3. WPA2 PreSharedKey is generated from KeyPassphrase.

When read, this parameter returns an empty string, regardless of the actual value.

The secret used for handshaking with the RADIUS server [RFC2865].

When read, this parameter returns an empty string, regardless of the actual value.

The secret used for handshaking with the secondary RADIUS server [RFC2865].

If this parameter is not implemented, the secondary RADIUS server will use the same secret as the primary RADIUS server.

When read, this parameter returns an empty string, regardless of the actual value.

{{list: parameter is not a list}} Indicates the current status of WPS. If the device goes to SetupLocked the WPS needs to be disabled and re-enabled to come out of state.

Enumeration of:

• Disabled
• Error
• Unconfigured
• Configured
• SetupLocked

Represents the Device PIN used for PIN based pairing between WPS peers. This PIN is either a four digit number or an eight digit number.{{hidden}}

Possible patterns:

• \d{4}|\d{8}

When read, this parameter returns an empty string, regardless of the actual value.

[MACAddress] The MAC address of an associated device.

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.MACAddress.

The data transmit rate in kbps that was most recently used for transmission from the access point to the associated device.

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.LastDataDownlinkRate.

Active Notification requests for this parameter MAY be denied.

The data transmit rate in kbps that was most recently used for transmission from the associated device to the access point.

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.LastDataUplinkRate.

Active Notification requests for this parameter MAY be denied.

Date and time in UTC when the device was associated

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.LastConnectTime.

An indicator of radio signal strength of the uplink from the associated device to the access point, measured in dBm, as an average of the last 100 packets received from the device.

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.SignalStrength.

An indicator of radio noise on the uplink from the associated device to the access point, measured in dBm, as an average of the last 100 packets received from the device (see ANPI definition in [Clause 10.11.9.4/802.11-2012])

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.MultiAPSTA.Noise.

The number of packets that had to be re-transmitted, from the last 100 packets sent to the associated device. Multiple re-transmissions of the same packet count as one.

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.RetransCount.

[StatsCounter64] The total number of bytes transmitted to the Associated Device, including framing characters.

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.BytesSent.

[StatsCounter64] The total number of bytes received from the Associated Device, including framing characters.

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.BytesReceived.

[StatsCounter64] The total number of packets transmitted to the Associated Device.

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.PacketsSent.

[StatsCounter64] The total number of packets received from the Associated Device.

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.PacketsReceived.

[StatsCounter32] The total number of outbound packets that could not be transmitted because of errors. These might be due to the number of retransmissions exceeding the retry limit, or from other causes.

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.ErrorsSent.

[StatsCounter32] The total number of inbound packets that contained errors preventing them from being delivered to a higher-layer protocol.

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.ErrorsReceived.

[StatsCounter32] The total number of transmitted packets which were retransmissions. Two retransmissions of the same packet results in this counter incrementing by two.

If the instance of this AssociatedDevice is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}., then this parameter is the same as Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.STA.{i}.RetransCount.

The secret used for handshaking with the RADIUS accounting server [RFC2865].

When read, this parameter returns an empty string, regardless of the actual value.

The secret used for handshaking with the secondary RADIUS accounting server [RFC2865].

If this parameter is not implemented, the secondary RADIUS server will use the same secret as the primary RADIUS server.

When read, this parameter returns an empty string, regardless of the actual value.

Comma-separated list of strings. Indicates which security modes this EndPoint instance is capable of supporting.

Each list item is an enumeration of:

• None
• WEP-64
• WEP-128
• WPA-Personal
• WPA2-Personal
• WPA3-Personal
• WPA-WPA2-Personal
• WPA3-Personal-Transition
• WPA-Enterprise
• WPA2-Enterprise
• WPA3-Enterprise
• WPA-WPA2-Enterprise
• OWE (Added in 2.16)

A WEP key expressed as a hexadecimal string.

WEPKey is used only if ModeEnabled is set to WEP-64 or WEP-128.

A 5 byte WEPKey corresponds to security mode WEP-64 and a 13 byte WEPKey corresponds to security mode WEP-128.

When read, this parameter returns an empty string, regardless of the actual value.