Organizationally unique identifier of the device manufacturer. Represented as a six hexadecimal-digit value using all upper-case letters and including any leading zeros. The value MUST be a valid OUI as defined in [OUI].

This value MUST remain fixed over the lifetime of the device, including across firmware updates.

Any change would indicate that it’s a new device and would therefore require a BOOTSTRAP Inform.

Model name of the CPE (human readable string).

Active Notification requests for this parameter MAY be denied.

A full description of the CPE device (human readable string).

Active Notification requests for this parameter MAY be denied.

Identifier of the class of product for which the serial number applies. That is, for a given manufacturer, this parameter is used to identify the product or class of product over which the SerialNumber parameter is unique.

This value MUST remain fixed over the lifetime of the device, including across firmware updates.

Any change would indicate that it’s a new device and would therefore require a BOOTSTRAP Inform.

Serial number of the CPE.

This value MUST remain fixed over the lifetime of the device, including across firmware updates.

Any change would indicate that it’s a new device and would therefore require a BOOTSTRAP Inform.

A string identifying the particular CPE model and version.

This parameter MUST always be included in Inform messages.

A string identifying the software version currently installed in the CPE. To allow version comparisons, this element SHOULD be in the form of dot-delimited integers, where each successive integer represents a more minor category of variation. For example, 3.0.21 where the components mean: Major.Minor.Build.

This parameter MUST always be included in Inform messages.

Current operational status of the device.

Enumeration of:

• Up
• Initializing
• Error
• Disabled

Time in seconds since the CPE was last restarted.

Active Notification requests for this parameter MAY be denied.

Date and time in UTC that the CPE first both successfully established an IP-layer network connection and acquired an absolute time reference using NTP or equivalent over that network connection. The CPE MAY reset this date after a factory reset.

If NTP or equivalent is not available, this parameter, if present, SHOULD be set to the Unknown Time value.

Active Notification requests for this parameter MAY be denied.

Vendor-specific log(s).

Active Notification requests for this parameter MAY be denied.

The free physical RAM, in kilobytes, currently available on the device.

Active Notification requests for this parameter MAY be denied.

The total amount of the CPU, in percent, rounded up to the nearest whole percent. In the case that multiple CPU are present, this value represents the average of all CPU.

Active Notification requests for this parameter MAY be denied.

The size in kilobytes of the memory occupied by the process.

Active Notification requests for this parameter MAY be denied.

The amount of time in milliseconds that the process has spent taking up CPU time since the process was started.

Active Notification requests for this parameter MAY be denied.

The current state that the process is in.

Enumeration of:

• Running
• Sleeping
• Stopped
• Idle (OPTIONAL)
• Uninterruptible (OPTIONAL)
• Zombie (OPTIONAL)

Active Notification requests for this parameter MAY be denied.

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

Active Notification requests for this parameter MAY be denied.

The status of this temperature sensor.

Enumeration of:

• Disabled (The sensor is not currently sampling the temperature)
• Enabled (The sensor is currently sampling the temperature)
• Error (The sensor error currently prevents sampling the temperature)

When set to true, resets the temperature sensor.

When read, this parameter returns false, regardless of the actual value.

• Status transition from Disabled to Enabled
• Reset set to true.
• An internal reset of the temperature sensor (including a reboot of the device). The Unknown Time value, as defined in [TR-106a2], indicates that this temperature sensor has never been reset, which can only happen if it has never been enabled.

This temperature sensor’s last good reading in degrees celsius. A value of -274 (which is below absolute zero) indicates a good reading has not been obtained since last reset.

Active Notification requests for this parameter MAY be denied.

The time at which this temperature sensor’s last good reading was obtained. The Unknown Time value, as defined in [TR-106a2], indicates a good reading has not been obtained since last reset.

Active Notification requests for this parameter MAY be denied.

This temperature sensor’s low alarm value in degrees celsius. A value of -274 (which is below absolute zero) indicates a non configured value.

A change to this value will cause LowAlarmTime to be reset.

This temperature sensor’s high alarm value in degrees celsius. A value of -274 (which is below absolute zero) indicates a non configured value.

A change to this value will cause HighAlarmTime to be reset.

Comma-separated list of strings. Indicates the TCP congestion control mechanism(s) implemented. Each list item is an enumeration of:

• Tahoe (Represents the base TCP implementation in [RFC793] and elements of [RFC2582])
• Reno (Represents the base TCP implementation in [RFC793] with the additional algorithms defined in [RFC2581])
• New Reno (Described as a modification to the Reno algorithms in [RFC2582])
• Vegas (An emerging TCP congestion control mechanism) Tahoe, Reno, and New Reno are defined in [RFC2582]

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

Active Notification requests for this parameter MAY be denied.

Comma-separated list of strings. This parameter MUST list exactly the features that are defined using the top-level feature element in the DT Instance referenced by URL. For example, if the DT instance specified the following:

then the value of this parameter might be DNSServer,Router,X_MyDeviceFeature. The order in which the features are listed is not significant.

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

Active Notification requests for this parameter MAY be denied.

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

Active Notification requests for this parameter MAY be denied.

The architecture of the processor on the underlying hardware. Enumeration of:

• arm
• i386
• m68010
• m68k
• mipseb (big-endian)
• mipsel (little-endian)
• powerpc
• sh3eb (big-endian)
• sh3el (little-endian)
• x86_64 For processor architectures not included in this list, the vendor MAY include vendor-specific values, which MUST use the format defined in [Section 3.3/TR-106a4].

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

Active Notification requests for this parameter MAY be denied.

Organizationally unique identifier of the associated CPE Proxier. Represented as a six hexadecimal-digit value using all upper-case letters and including any leading zeros. Possible patterns:

• [0-9A-F]{6} The value MUST be a valid OUI as defined in [OUI].

The protocol being used to communicate between the CPE Proxier and this Proxied Device. Enumeration of:

• Z-Wave (see [Z-Wave])
• ZigBee (see [ZigBee])
• UPnP-DM (see [UPnP-DM:1])
• ETSI-M2M (see [ETSIM2MFA]) Vendors can extend the enumerated values with vendor specific extensions, in which case the rules outlined in [Section 3.3/TR-106a6] MUST be adhered to.

Identifies the source of the location data.

Enumeration of:

• GPS
• AGPS
• Manual
• External

URL, MAC address, or other identifier that identifies an “External” source of this location. Meaningful only if Source has a value of External, otherwise it MUST be an empty string. If ExternalProtocol has a value of CWMP, this is the URL or IP address of the ACS.

The Agent MUST choose an initial value that doesn’t conflict with any existing entries.

Protocol used to acquire a location from an “External” source. Enumeration of:

• <Empty> (An empty string)
• CWMP
• OMA-DM
• SNMP
• UPnP
• HELD
• DHCPv4
• DHCPv6
• LLDP-MED
• MLP
• Other Meaningful only if Source has a value of External, otherwise it MUST be an empty string.

The currently valid location information. Writable only when ExternalProtocol has a value of CWMP. If obtained through the local GPS/AGPS then the location information is formatted according to [RFC5491].

If manually configured then location information will be XML-formatted according to [RFC5491] (geographical information) and [RFC5139] (civic addresses). If obtained by an external source this is the location information as received. If it’s an XML document (e.g. CWMP, OMA-DM, UPnP, HELD, MLP) the location information will be represented as-is, otherwise it will be converted to base64. CWMP configured location information will be XML-formatted according to [RFC5491] (geographical information) and [RFC5139] (civic addresses). Only zero or one Location object instance with value CWMP MUST exist at any given time.

Enables and disables the CPE’s support for CWMP. false means that CWMP support in the CPE is disabled, in which case the device MUST NOT send any Inform messages to the ACS or accept any Connection Request notifications from the ACS. true means that CWMP support on the CPE is enabled. The subscriber can re-enable the CPE’s CWMP support either by performing a factory reset or by using a LAN-side protocol to change the value of this parameter back to true.

The factory default value MUST be true.

Username used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This username is used only for HTTP-based authentication of the CPE.

Note that on a factory reset of the CPE, the value of this parameter might be reset to its factory value. If an ACS modifies the value of this parameter, it SHOULD be prepared to accommodate the situation that the original value is restored as the result of a factory reset.

Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This password is used only for HTTP-based authentication of the CPE. When read, this parameter returns an empty string, regardless of the actual value.

Note that on a factory reset of the CPE, the value of this parameter might be reset to its factory value. If an ACS modifies the value of this parameter, it SHOULD be prepared to accommodate the situation that the original value is restored as the result of a factory reset.

When read, this parameter returns an empty string, regardless of the actual value.

ParameterKey provides the ACS a reliable and extensible means to track changes made by the ACS. The value of ParameterKey MUST be equal to the value of the ParameterKey argument from the most recent successful SetParameterValues, AddObject, or DeleteObject method call from the ACS. The CPE MUST set ParameterKey to the value specified in the corresponding method arguments if and only if the method completes successfully and no fault response is generated. If a method call does not complete successfully (implying that the changes requested in the method did not take effect), the value of ParameterKey MUST NOT be modified. The CPE MUST only modify the value of ParameterKey as a result of SetParameterValues, AddObject, DeleteObject, or due to a factory reset. On factory reset, the value of ParameterKey MUST be set to an empty string.

This parameter MUST always be included in Inform messages.

Active Notification requests for this parameter MAY be denied.

HTTP URL, as defined in [RFC3986], for an ACS to make a Connection Request notification to the CPE. In the form:

http://host:port/path The host portion of the URL MAY be the IP address for the management interface of the CPE in lieu of a host name.

This parameter MUST always be included in Inform messages.

Password used to authenticate an ACS making a Connection Request to the CPE. When read, this parameter returns an empty string, regardless of the actual value.

When read, this parameter returns an empty string, regardless of the actual value.

Address and port to which an ACS MAY send a UDP Connection Request to the CPE (see [Annex G/TR-069a2]). This parameter is represented in the form of an Authority element as defined in [RFC3986]. The value MUST be in one of the following two forms:

host:port

host

• When STUNEnable is true, the host and port portions of this parameter MUST represent the public address and port corresponding to the NAT binding through which the ACS can send UDP Connection Request messages (once this information is learned by the CPE through the use of STUN).
• When STUNEnable is false, the host and port portions of the URL MUST represent the local IP address and port on which the CPE is listening for UDP Connection Request messages. The second form of this parameter MAY be used only if the port value is equal to 80.

The value of the STUN Password to be used in computing the MESSAGE-INTEGRITY attribute to be used in Binding Requests (only if message integrity has been requested by the STUN server). When read, this parameter returns an empty string, regardless of the actual value.

When read, this parameter returns an empty string, regardless of the actual value.

Indicates whether or not the Alias-Based Addressing Mechanism is supported. A true value indicates that the CPE supports the Alias-Based Addressing Mechanism, as defined in [Section 3.6.1/TR-069a4] and described in [Appendix II/TR-069a4].

This parameter MUST always be included in Inform messages.

Instance identification mode as defined in [Section 3.6.1/TR-069a4]. When AliasBasedAddressing is true, InstanceMode is used by the ACS to control whether the CPE will use Instance Numbers or Instance Aliases in returned Path Names. Enumeration of:

• InstanceNumber
• InstanceAlias This parameter is REQUIRED for any CPE supporting Alias-Based Addressing.

The factory default value MUST be InstanceNumber.

Enable or disable the Auto-Create Instance Mechanism. When AliasBasedAddressing is true, AutoCreateInstances indicates whether or not the CPE will automatically create instances while processing a SetParameterValues RPC (as defined in [A.3.2.1/TR-069a4]). *A true value indicates that the CPE will perform auto-creation of instances when the Alias-Based Addressing Mechanism is used in SetParameterValues RPC. *A false value indicates that the CPE will not create new object instances. Instead, it will reject the setting of parameters in unrecognized instances and respond with a fault code. This parameter is REQUIRED for any CPE supporting Alias-Based Addressing.

The factory default value MUST be false.

Comma-separated list of strings. The connection request methods supported by this ManagementServer. Each list item is an enumeration of:

• HTTP (The connection request method as specified in [Section 3.2.2 ACS Connection Initiation/TR-069], REQUIRED)
• STUN (The connection request method as specified in [Annex G Connection Request via NAT Gateway/TR-069], OPTIONAL)
• XMPP (The connection request method as specified in [Annex K XMPP Connection Request/TR-069a5], OPTIONAL)

• “ACS1@tr069.example.com/resource1”
• “ACS1@tr069.example.com/resource2”
• “ACS2@tr069.example.com/resource1” And the following incoming “from” addresses would not be allowed:
• “ACS2@tr069.example.com/resource2”
• “ACS@tr069.example.com/resource” If this Parameter is an empty string then all Jabber IDs are allowed and an XMPP Connection Request can not be deemed invalid due to the “from” address.

The value MUST be the value of the XMPP.Connection.{i}.JabberID contained in the XMPP.Connection instance referenced by the ConnReqXMPPConnection parameter. If the ConnReqXMPPConnection parameter is empty or the XMPP.Connection instance being reference is disabled, then this value will be empty. If the XMPP.Connection instance being referenced by the ConnReqXMPPConnection parameter is lost (XMPP.Connection.{i}.Status parameter changes from Enabled to some other value), then the value of this parameter MUST remain unchanged until the connection can be reestablished and a new XMPP.Connection.{i}.JabberID can be established. If the new XMPP.Connection.{i}.JabberID is identical to the existing value, then the value of this parameter MUST NOT be altered and a VALUE CHANGE event MUST NOT be generated.

Active Notification MUST by default be enabled for this parameter.

Comma-separated list of strings. Indicates the HTTP Compression mechanism(s) supported by this CPE. Requirements for the use of HTTP Compression for CWMP can be found in [Section 3.4.7/TR-069a5]. Each list item is an enumeration of:

• GZIP (As defined in [Section 3.5/RFC2616])
• Compress (As defined in [Section 3.5/RFC2616])
• Deflate (As defined in [Section 3.5/RFC2616]) Vendors can extend the enumerated values with vendor specific extensions, in which case the rules outlined in [Section 3.3/TR-106a7] MUST be adhered to.

The value MUST be a member of the list reported by the HTTPCompressionSupported parameter, or else be Disabled. The value of this parameter represents the HTTP Compression mechanism to be used by the CPE when communicating with the ACS.

The factory default value MUST be Disabled.

Comma-separated list of strings. Indicates the Lightweight Notification Protocol(s) supported by this CPE. Each list item is an enumeration of:

• UDP (As defined in [Annex M/TR-069a5]) Vendors can extend the enumerated values with vendor specific extensions, in which case the rules outlined in [Section 3.3/TR-106a7] MUST be adhered to.

Indicates the transfer types that MUST be included when the CPE notifies the ACS of AUTONOMOUS TRANSFER COMPLETE events. Transfer types not indicated by this filter MUST NOT be included when the CPE notifies the ACS. Enumeration of:

• Upload
• Download
• Both (Upload and Download) Note that this includes any backup or restore operations that were not specifically requested by the ACS. A backup is regarded as an Upload and a restore is regarded as a Download.

Indicates the transfer results that MUST be included when the CPE notifies the ACS of AUTONOMOUS TRANSFER COMPLETE events. Transfer results omitted from this list MUST NOT be included when the CPE notifies the ACS. Note that this includes any backup or restore operations that were not specifically requested by the ACS. A backup is regarded as an Upload and a restore is regarded as a Download.

Enumeration of:

• Success (The autonomous file transfer completed successfully; i.e., the FaultCode was zero)
• Failure (The autonomous file transfer did not complete successfully; i.e., the FaultCode was non-zero)
• Both (Success and Failure)

Comma-separated list (maximum number of characters 1024) of strings. Indicates the file types that MUST be included when the CPE notifies the ACS of AUTONOMOUS TRANSFER COMPLETE events. File types omitted from this list MUST NOT be included when the CPE notifies the ACS.

Each list item matches one of:

• 1 Firmware Upgrade Image (Download Only)
• 2 Web Content (Download Only)
• 3 Vendor Configuration File (Download or Upload)
• 4 Vendor Log File (Upload Only)
• X [0-9A-F]{6} .* (For Vendor-Specific File Types, could be for either Download or Upload) Additionally, the following format is defined to allow the unique definition of vendor-specific file types:
• “X ” is replaced by a 6 hexadecimal-digit OUI (organizationally unique identifier) as defined in [OUI], with all upper-case letters and any leading zeros included. The OUI used for a given vendor-specific file type MUST be one that is assigned to the organization that defined this file type (which is not necessarily the same as the vendor of the CPE or ACS). Note that an empty string indicates that all file types are excluded from this filter, effectively disabling CPE notification of AUTONOMOUS TRANSFER COMPLETE events to the ACS.

Comma-separated list of strings. Indicates the Deployment Unit operations that MUST be included when the CPE notifies the ACS of “12 AUTONOMOUS DU STATE CHANGE COMPLETE” events. Operation types not indicated by this list MUST NOT be included when the CPE notifies the ACS. An empty string is essentially the same as setting Enable to false.

Each list item is an enumeration of:

• Install
• Update
• Uninstall

Indicates the Deployment Unit state change results that MUST be included when the CPE notifies the ACS of “12 AUTONOMOUS DU STATE CHANGE COMPLETE” events. State change results omitted from this filter MUST NOT be included when the CPE notifies the ACS.

Enumeration of:

• Success (The autonomous state change completed successfully; i.e., the FaultCode was zero)
• Failure (The autonomous state change did not complete successfully; i.e., the FaultCode was non-zero)
• Both (All result types independent of Success or Failure)

Comma-separated list of strings. Indicates the Deployment Unit state change fault codes that MUST be included when the CPE notifies the ACS of “12 AUTONOMOUS DU STATE CHANGE COMPLETE” events. State change fault codes omitted from this filter MUST NOT be included when the CPE notifies the ACS. This filter has no effect on the notification of a successful autonomous state change. This filter only applies when ResultTypeFilter is set to either Failure or Both. An empty string means that failed autonomous state changes will not be sent to the ACS.

Each list item is an enumeration of:

• 9001
• 9003
• 9012
• 9013
• 9015
• 9016
• 9017
• 9018
• 9022
• 9023
• 9024
• 9025
• 9026
• 9027
• 9028
• 9029
• 9030
• 9031
• 9032

When waking up from a non CR-Aware Standby that lasted more than this parameter’s value (in seconds), the CPE MUST issue a WAKEUP Event. If the value is -1, the CPE MUST NOT ever issue WAKEUP Events for having been non CR-aware.

The factory default value MUST be -1.

When waking up from a non fully Timer-Aware Standby that made it miss more than this parameter’s value Periodic Contacts, the CPE MUST issue a WAKEUP Event. If the value is -1, the CPE MUST NOT ever issue WAKEUP Events for exceeding that limit.

The factory default value MUST be -1.

When waking up from a non fully Timer-Aware Standby that made it miss at least one Scheduled Contact, the CPE MUST issue a WAKEUP Event if this parameter is true.

The factory default value MUST be false.

If NetworkAwarenessCapable and this parameter are both true, the CPE MUST NOT go into a non CR-Aware Standby state.

The factory default value MUST be false.

If SelfTimerCapable and this parameter are both true, the CPE MUST NOT go into a standby state that prevents it from honoring Periodic Contacts.

The factory default value MUST be false.

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

The Agent MUST choose an initial value that doesn’t conflict with any existing entries.

Organizationally unique identifier of the associated Internet Gateway Device. An empty string indicates that there is no associated Internet Gateway Device that has been detected.

Active Notification MUST by default be enabled for this parameter.

Identifier of the product class of the associated Internet Gateway Device. An empty string indicates either that there is no associated Internet Gateway Device that has been detected, or the Internet Gateway Device does not support the use of the product-class parameter.

Active Notification MUST by default be enabled for this parameter.

Serial number of the associated Internet Gateway Device. An empty string indicates that there is no associated Internet Gateway Device that has been detected.

Active Notification MUST by default be enabled for this parameter.

A dump of the currently running configuration on the CPE. This parameter enables the ability to backup and restore the last known good state of the CPE. It returns a vendor-specific document that defines the state of the CPE. The document MUST be capable of restoring the CPE’s state when written back to the CPE using SetParameterValues.

An alternative to this parameter, e.g. when the configuration file is larger than the parameter size limit, is to use the Upload and Download RPCs with a FileType of 1 Vendor Configuration File.

The current date and time in the CPE’s local time zone.

Active Notification requests for this parameter MAY be denied.

The local time zone definition, encoded according to IEEE 1003.1 (POSIX). The following is an example value:

EST+5 EDT,M4.1.0/2,M10.5.0/2

Status of Time support on the CPE. Enumeration of:

• Disabled
• Unsynchronized
• Synchronized
• Error_FailedToSynchronize
• Error (OPTIONAL) The Unsynchronized value indicates that the CPE’s absolute time has not yet been set. The Synchronized value indicates that the CPE has acquired accurate absolute time; its current time is accurate. The Error_FailedToSynchronize value indicates that the CPE failed to acquire accurate absolute time; its current time is not accurate. The Error value MAY be used by the CPE to indicate a locally defined error condition.

Comma-separated list of strings. Indicates the protocols that are supported by the CPE for the purpose of remotely accessing the user interface.

Each list item is an enumeration of:

• HTTP (As defined in [RFC2616])
• HTTPS (As defined in [RFC2818])

The horizontal position of the User Interface’s top left corner within the local CPE’s display measured from the top left corner, expressed in pixels.

Active Notification requests for this parameter MAY be denied.

The vertical position of the User Interface’s top left corner within the local CPE’s display measured from the top left corner, expressed in pixels.

Active Notification requests for this parameter MAY be denied.

The width of the user interface within the local CPE’s display, expressed in pixels.

Active Notification requests for this parameter MAY be denied.

The height of the user interface within the local CPE’s display, expressed in pixels.

Active Notification requests for this parameter MAY be denied.

The method used to assign an address to this interface. Enumeration of:

• DHCP
• Static The ability to modify this parameter is OPTIONAL.

[IPAddress] The current IP address assigned to this interface. The ability to modify this parameter is OPTIONAL, and this parameter cannot be modified if the AddressingType is DHCP.

This parameter MUST always be included in Inform messages.

• When true, MACAddress is writable.
• When false, MACAddress is not writable, and the default MAC address assigned by the device SHOULD be restored.

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

The Agent MUST choose an initial value that doesn’t conflict with any existing entries.

Active Notification requests for this parameter MAY be denied.

• When true, this entry represents a request. In this case, the DHCP client MUST include the specified Tag in the Parameter Request List, as defined in RFC 2132. The Value parameter is ignored in this case.
• When false, this entry represents a value to be sent by the DHCP client. In this case, the DHCP client MUST include a DHCP option formed from the Tag and Value parameters (with the Length derived from the length of the Value parameter).

The time in seconds that this IP interface has been connected.

• If the IP interface is using DHCP, this is the time that the DHCP client has been only in the Bound or Renewing states and the lower-layer interface has continuously maintained a link.
• If the IP interface is using static addressing, this is the time that the lower-layer interface has continuously maintained a link.

Active Notification requests for this parameter MAY be denied.

Total number of IP payload bytes sent over this interface since the device was last restarted as specified in DeviceInfo.UpTime.

Active Notification requests for this parameter MAY be denied.

Total number of IP payload bytes received over this interface since the device was last restarted as specified in DeviceInfo.UpTime.

Active Notification requests for this parameter MAY be denied.

Total number of IP packets sent over this interface since the device was last restarted as specified in DeviceInfo.UpTime.

Active Notification requests for this parameter MAY be denied.

Total number of IP packets received over this interface since the device was last restarted as specified in DeviceInfo.UpTime.

Active Notification requests for this parameter MAY be denied.

Number of seconds since the beginning of the period used for collection of CurrentDay statistics. The device MAY align the beginning of each CurrentDay interval with days in the UTC time zone, but does not need to do so.

Active Notification requests for this parameter MAY be denied.

Total number of IP payload bytes sent over this interface since the beginning of the current-day interval as specified by CurrentDayInterval.

Active Notification requests for this parameter MAY be denied.

Total number of IP payload bytes received over this interface since the beginning of the current-day interval as specified by CurrentDayInterval.

Active Notification requests for this parameter MAY be denied.

Total number of IP packets sent over this interface since the beginning of the current-day interval as specified by CurrentDayInterval.

Active Notification requests for this parameter MAY be denied.

Total number of IP packets received over this interface since the beginning of the current-day interval as specified by CurrentDayInterval.

Active Notification requests for this parameter MAY be denied.

Number of seconds since the beginning of the period used for collection of QuarterHour statistics. The device MAY align the beginning of each QuarterHour interval with real-time quarter-hour intervals, but does not need to do so.

Active Notification requests for this parameter MAY be denied.

Total number of IP payload bytes sent over this interface since the beginning of the quarter-hour interval as specified by QuarterHourInterval.

Active Notification requests for this parameter MAY be denied.

Total number of IP payload bytes received over this interface since the beginning of the quarter-hour interval as specified by QuarterHourInterval.

Active Notification requests for this parameter MAY be denied.

Total number of IP packets sent over this interface since the beginning of the quarter-hour interval as specified by QuarterHourInterval.

Active Notification requests for this parameter MAY be denied.

Total number of IP packets received over this interface since the beginning of the quarter-hour interval as specified by QuarterHourInterval.

Active Notification requests for this parameter MAY be denied.

Indicates availability of diagnostic data. Enumeration of:

• None
• Requested
• Complete
• Error_CannotResolveHostName
• Error_Internal
• Error_Other If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Complete (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Complete, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code 8 DIAGNOSTICS COMPLETE in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None. Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None. While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None. While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

Active Notification requests for this parameter MAY be denied.

Result parameter indicating the number of successful pings (those in which a successful response was received prior to the timeout) in the most recent ping test.

Active Notification requests for this parameter MAY be denied.

Result parameter indicating the number of failed pings in the most recent ping test.

Active Notification requests for this parameter MAY be denied.

Result parameter indicating the average response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero.

Active Notification requests for this parameter MAY be denied.

Result parameter indicating the minimum response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero.

Active Notification requests for this parameter MAY be denied.

Result parameter indicating the maximum response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero.

Active Notification requests for this parameter MAY be denied.

Indicates availability of diagnostic data. Enumeration of:

• None
• Requested
• Complete
• Error_CannotResolveHostName
• Error_MaxHopCountExceeded
• Error_Internal
• Error_Other If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Complete (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Complete, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code 8 DIAGNOSTICS COMPLETE in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None. Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None. While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None. While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

Active Notification requests for this parameter MAY be denied.

Result parameter indicating the response time in milliseconds the most recent trace route test. If a route could not be determined, this value MUST be zero.

Active Notification requests for this parameter MAY be denied.

Result parameter indicating the number of hops within the discovered route. If a route could not be determined, this value MUST be zero.

Active Notification requests for this parameter MAY be denied.

Result parameter indicating the Host Name or IP Address of a hop along the discovered route.

Active Notification requests for this parameter MAY be denied.

Comma-separated list of strings. Supported DownloadDiagnostics transport protocols for a CPE device.

Each list item is an enumeration of:

• HTTP
• FTP (OPTIONAL)

Comma-separated list of strings. Supported UploadDiagnostics transport protocols for a CPE device.

Each list item is an enumeration of:

• HTTP
• FTP (OPTIONAL)

Indicate the availability of diagnostic data. Enumeration of:

• None (READONLY)
• Requested
• Completed (READONLY)
• Error_InitConnectionFailed (READONLY)
• Error_NoResponse (READONLY)
• Error_TransferFailed (READONLY)
• Error_PasswordRequestFailed (READONLY)
• Error_LoginFailed (READONLY)
• Error_NoTransferMode (READONLY)
• Error_NoPASV (READONLY)
• Error_IncorrectSize (READONLY)
• Error_Timeout (READONLY) If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Completed (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Completed, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code 8 DIAGNOSTICS COMPLETE in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None. Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None. While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None. While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

Active Notification requests for this parameter MAY be denied.

• When using FTP transport, FTP binary transfer MUST be used.
• When using HTTP transport, persistent connections MUST be used and pipelining MUST NOT be used.
• When using HTTP transport the HTTP Authentication MUST NOT be used.

Request time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

• For HTTP this is the time at which the client sends the GET command.
• For FTP this is the time at which the client sends the RTRV command.

Active Notification requests for this parameter MAY be denied.

Begin of transmission time in UTC, which MUST be specified to microsecond precision For example: 2008-04-09T15:01:05.123456

• For HTTP this is the time at which the first data packet is received.
• For FTP this is the time at which the client receives the first data packet on the data connection.

Active Notification requests for this parameter MAY be denied.

End of transmission in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

• For HTTP this is the time at which the last data packet is received.
• For FTP this is the time at which the client receives the last packet on the data connection.

Active Notification requests for this parameter MAY be denied.

The test traffic received in bytes during the FTP/HTTP transaction including FTP/HTTP headers, between BOMTime and EOMTime,

Active Notification requests for this parameter MAY be denied.

The total number of bytes received on the Interface between BOMTime and EOMTime.

Active Notification requests for this parameter MAY be denied.

Request time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

• For HTTP this is the time at which the TCP socket open (SYN) was sent for the HTTP connection.
• For FTP this is the time at which the TCP socket open (SYN) was sent for the data connection. Note: Interval of 1 microsecond SHOULD be supported.

Active Notification requests for this parameter MAY be denied.

Response time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

• For HTTP this is the time at which the TCP ACK to the socket opening the HTTP connection was received.
• For FTP this is the time at which the TCP ACK to the socket opening the data connection was received. Note: Interval of 1 microsecond SHOULD be supported.

Active Notification requests for this parameter MAY be denied.

Indicate the availability of diagnostic data. Enumeration of:

• None (READONLY)
• Requested
• Completed (READONLY)
• Error_InitConnectionFailed (READONLY)
• Error_NoResponse (READONLY)
• Error_PasswordRequestFailed (READONLY)
• Error_LoginFailed (READONLY)
• Error_NoTransferMode (READONLY)
• Error_NoPASV (READONLY)
• Error_NoCWD (READONLY)
• Error_NoSTOR (READONLY)
• Error_NoTransferComplete (READONLY) If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Completed (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Completed, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code 8 DIAGNOSTICS COMPLETE in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None. Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None. While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None. While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

Active Notification requests for this parameter MAY be denied.

• When using FTP transport, FTP binary transfer MUST be used.
• When using HTTP transport, persistent connections MUST be used and pipelining MUST NOT be used.
• When using HTTP transport the HTTP Authentication MUST NOT be used.

Request time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

• For HTTP this is the time at which the client sends the PUT command
• For FTP this is the time at which the STOR command is sent.

Active Notification requests for this parameter MAY be denied.

Begin of transmission time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

• For HTTP this is the time at which the first data packet is sent.
• For FTP this is the time at which the client receives the ready for transfer notification.

Active Notification requests for this parameter MAY be denied.

End of transmission in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

• For HTTP this is the time when the HTTP successful response code is received.
• For FTP this is the time when the client receives a transfer complete.

Active Notification requests for this parameter MAY be denied.

The total number of bytes sent on the Interface between BOMTime and EOMTime.

Active Notification requests for this parameter MAY be denied.

Request time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

• For HTTP this is the time at which the TCP socket open (SYN) was sent for the HTTP connection.
• For FTP this is the time at which the TCP socket open (SYN) was sent for the data connection Note: Interval of 1 microsecond SHOULD be supported.

Active Notification requests for this parameter MAY be denied.

Response time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

• For HTTP this is the Time at which the TCP ACK to the socket opening the HTTP connection was received.
• For FTP this is the Time at which the TCP ACK to the socket opening the Data connection was received. Note: Interval of 1 microsecond SHOULD be supported.

Active Notification requests for this parameter MAY be denied.

Incremented upon each valid UDP echo packet received.

Active Notification requests for this parameter MAY be denied.

Incremented for each UDP echo response sent.

Active Notification requests for this parameter MAY be denied.

The number of UDP received bytes including payload and UDP header after the UDPEchoConfig is enabled.

Active Notification requests for this parameter MAY be denied.

The number of UDP responded bytes, including payload and UDP header sent after the UDPEchoConfig is enabled.

Active Notification requests for this parameter MAY be denied.

Time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456, The time that the server receives the first UDP echo packet after the UDPEchoConfig is enabled.

Active Notification requests for this parameter MAY be denied.

Time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456 The time that the server receives the most recent UDP echo packet.

Active Notification requests for this parameter MAY be denied.

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

The Agent MUST choose an initial value that doesn’t conflict with any existing entries.

Active Notification requests for this parameter MAY be denied.

The user’s password.

When read, this parameter returns an empty string, regardless of the actual value.

The status of the UPnP root device. Enumeration of:

• LeaseActive (Device is active and UPnP lease has not expired)
• LeaseExpired (Device is inactive because UPnP lease has expired)
• ByebyeReceived (Device is inactive because byebye message was received) The ability to list inactive UPnP root devices is OPTIONAL. The length of time an inactive device remains listed in this table is a local matter to the CPE.

This UPnP root device’s UUID (Universally Unique IDentifier) [RFC4122], extracted from any of its USN (Unique Service Name) headers. This is a 36-byte string that uniquely identifies the device, the following is an example:

02c29d2a-dbfd-2d91-99c9-306d537e9856

Possible patterns:

• [0-9A-Fa-f]{8}-([0-9A-Fa-f]{4}-){3}[0-9A-Fa-f]{12}

The value of the USN (Unique Service Name) header for this UPnP root device. Three discovery messages are sent for root devices, and this SHOULD be the value of the USN header of the following form:

uuid:device-UUID::urn:domain-name:device:deviceType:v SSDP is an unreliable protocol and it is possible that no discovery message containing the USN header of the above form was ever received. If so, one of the other two forms MAY be used:

uuid:device-UUID::upnp:rootdevice

uuid:device-UUID (for root device UUID)

The value of the SERVER header for this UPnP root device, which is a string of the following form:

OS/version UPnP/udaversion product/version where UPnP is a literal string, udaversion is the version of the UPnP Device Architecture.

The status of the UPnP embedded device. Enumeration of:

• LeaseActive (Device is active and UPnP lease has not expired)
• LeaseExpired (Device is inactive because UPnP lease has expired)
• ByebyeReceived (Device is inactive because byebye message was received) The ability to list inactive UPnP embedded devices is OPTIONAL. The length of time an inactive device remains listed in this table is a local matter to the CPE.

This UPnP embedded device’s UUID (Universally Unique IDentifier) [RFC4122], extracted from any of its USN (Unique Service Name) headers. This is a 36-byte string that uniquely identifies the device, the following is an example:

02c29d2a-dbfd-2d91-99c9-306d537e9856

Possible patterns:

• [0-9A-Fa-f]{8}-([0-9A-Fa-f]{4}-){3}[0-9A-Fa-f]{12}

The value of the USN (Unique Service Name) header for this UPnP embedded device. Two discovery messages are sent for embedded devices, and this SHOULD be the value of the USN header of the following form:

uuid:device-UUID::urn:domain-name:device:deviceType:v SSDP is an unreliable protocol and it is possible that no discovery message containing the USN header of the above form was ever received. If so, the other form MAY be used:

uuid:device-UUID

The value of the SERVER header for this UPnP embedded device, which is a string of the following form:

OS/version UPnP/udaversion product/version where UPnP is a literal string, udaversion is the version of the UPnP Device Architecture.

The status of the UPnP embedded service. Enumeration of:

• LeaseActive (Service is active and UPnP lease has not expired)
• LeaseExpired (Service is inactive because UPnP lease has expired)
• ByebyeReceived (Service is inactive because byebye message was received) The ability to list inactive UPnP embedded services is OPTIONAL. The length of time an inactive service remains listed in this table is a local matter to the CPE.

The value of the USN (Unique Service Name) header for this UPnP embedded service. This is of the following form:

uuid:device-UUID::urn:domain-name:service:serviceType:v

The value of the SERVER header for this UPnP embedded service, which is a string of the following form:

OS/version UPnP/udaversion product/version where UPnP is a literal string, udaversion is the version of the UPnP Device Architecture.

The UPnP Device Architecture version extracted from the specVersion element in the Device Description Document of the discovered root device. The SpecVersion is encoded as “major revison.minor revision”. Possible patterns:

• \d+\.\d+

The value of an element in the Device Description Document for this DeviceInstance that indicates the manufacturer OUI if this value is provided by the device; or an empty string if this value is not provided by the device. Possible patterns:

• <Empty> (an empty string)
• [0-9A-F]{6} Note: It is assumed that the htip:X_ManufacturerOUI element is used for HTIP (Home-network Topology Identifying Protocol) [JJ-300.00] and [G.9973].

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

Active Notification requests for this parameter MAY be denied.

Indicates the status of this smart card reader.

Enumeration of:

• Disabled
• Enabled (Indicates the smart card reader is enabled and functioning properly)
• Error (Indicates the smart card reader is enabled and not functioning properly)

When set to true, resets the SmartCard Reader and the associated SmartCard.

When read, this parameter returns false, regardless of the actual value.

• Status transition from Disabled to Enabled
• Reset set to true.
• An internal reset of the SmartCard Reader (including a reboot of the device). Unknown Time value indicates that this SmartCard Reader has never been reset, which can only happen if it has never been enabled.

Counter incremented once each time decryption cannot be carried out. This counter relates to the smart card reader, not to the smart card itself, i.e. it is reset when the Reset parameter is used and not when a Smart Card is inserted or removed.

Active Notification requests for this parameter MAY be denied.

Counter incremented once each time the key is not available to decrypt it. This is a subset of the more general DecryptionFailedCounter within the same object and thus will always be less than that parameter. This counter relates to the smart card reader, not to the smart card itself, i.e. it is reset when the Reset parameter is used and not when a Smart Card is inserted or removed.

Active Notification requests for this parameter MAY be denied.

Status of the Smart Card.

Enumeration of:

• None (Indicates that no Smart Card is inserted)
• Running (Indicates a Smart Card is present and working normally)
• Error (Indicates the Smart Card is present and in an error condition)

Smart Card Type. Enumeration of:

• CA
• DRM
• UICC Vendors can extend the enumerated values with vendor specific extensions, in which case the rules outlined in [Section 3.3/TR-106a2] MUST be adhered to.

Comma-separated list of strings. Indicates Smart Card Application(s). Application is only relevant when Type has a value of UICC, otherwise it is an empty string. Each list item is an enumeration of:

• SIM
• USIM
• ISIM Vendors can extend the enumerated values with vendor specific extensions, in which case the rules outlined in [Section 3.3/TR-106a2] MUST be adhered to.

Indicates availability of diagnostic data. Enumeration of:

• None (READONLY)
• Requested
• Complete (READONLY)
• Error_Internal (READONLY)
• Error_Other (READONLY) If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Complete (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Complete, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code “8 DIAGNOSTICS COMPLETE” in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None. Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None. While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None. While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

Active Notification requests for this parameter MAY be denied.

Results of self-test (vendor specific).

Active Notification requests for this parameter MAY be denied.

Indicates availability of diagnostic data. Enumeration of:

• None (READONLY)
• Requested
• Complete (READONLY)
• Error_DNSServerNotResolved (Unable to resolve DNSServer Name, READONLY)
• Error_Internal (READONLY)
• Error_Other (READONLY) If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Complete (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Complete, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code “8 DIAGNOSTICS COMPLETE” in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None. Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None. While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None. While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

Active Notification requests for this parameter MAY be denied.

Number of successfully executed repetitions.

Active Notification requests for this parameter MAY be denied.

The number of entries in the Result table. Total number of Result entries from the most recent invocation of the test.

Active Notification requests for this parameter MAY be denied.

Result Parameter to represent whether the NS Lookup was successful or not. Errors for individual Result instances do not get bubbled up to DiagnosticsState. A failure on a specific attempt does not mean that the overall test failed, but a failure on all attempts means that DiagnosticsState SHOULD be Error_Other.

Enumeration of:

• Success
• Error_DNSServerNotAvailable
• Error_HostNameNotResolved
• Error_Timeout
• Error_Other

Active Notification requests for this parameter MAY be denied.

Result parameter to represent whether the answer is Authoritative or not.

Enumeration of:

• None (Indicates that the NS Lookup failed to find the host)
• Authoritative
• NonAuthoritative

Active Notification requests for this parameter MAY be denied.

Result parameter to represent the fully qualified name for the Host Name in the calling parameter (e.g. HostName.DomainName); if no response was provided, then this parameter is an empty string.

Active Notification requests for this parameter MAY be denied.

[IPAddress] Comma-separated list (up to 10 items) of IP Addresses. Indicates the IP Address results returned by the NS Lookup; if no response was provided, then this parameter is an empty string.

Active Notification requests for this parameter MAY be denied.

[IPAddress] Result parameter to represent the actual DNS Server IP address that the NS Lookup used.

Active Notification requests for this parameter MAY be denied.

Response time (for the first response packet) in milliseconds, or 0 if no response was received.

Active Notification requests for this parameter MAY be denied.

How this firewall is configured. Enumeration of:

• High (The firewall implements the “Traffic Denied Inbound” and “Minimally Permit Common Services Outbound” components of the ICSA residential certification’s Required Services Security Policy [ICSA-Residential]. If DoS and vulnerability protections are implemented [ICSA-Baseline], these are enabled)
• Low (All Outbound traffic and pinhole-defined Inbound traffic is allowed. If DoS and vulnerability protections are implemented [ICSA-Baseline], these are enabled)
• Off (All Inbound and Outbound traffic is allowed, and the CPE is only protected by NAT settings (if supported and enabled). If DoS and vulnerability protections are implemented [ICSA-Baseline], these are disabled) Vendors can extend the enumerated values with vendor specific extensions, in which case the rules outlined in [Section 3.3/TR-106a2] MUST be adhered to.

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

Active Notification requests for this parameter MAY be denied.

Type of USB Host

Enumeration of:

• OHCI (Open Host Controller Interface)
• EHCI (Enhanced Host Controller Interface)
• UHCI (Universal Host Controller Interface)
• xHCI (Extensible Host Controller Interface)

When set to true, reset the Host Controller and apply the reset signaling (see [Chapter 7.1.7.5/USB2.0]) to all of the Host Controller Hub downstream ports. The value is not saved in the device’s state and setting it to false has no effect.

When read, this parameter returns false, regardless of the actual value.

Speed of the USB device. Enumeration of:

• Low (1.5 Mbits/sec (187.5 KB/sec) defined in [USB1.0])
• Full (12 Mbits/sec (1.5 MB/sec) defined in [USB1.0])
• High (480 Mbits/sec (60 MB/sec) defined in [USB2.0])
• Super (5.0 Gbits/sec (625 MB/sec) defined in [USB3.0]) Internal signaling between the connected USB device and the USB Host Controller provide the information needed to determine the negotiated rate.

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

The Agent MUST choose an initial value that doesn’t conflict with any existing entries.

Active Notification requests for this parameter MAY be denied.

Indicates availability of Sample statistics. Enumeration of:

• Disabled (Collection is disabled)
• Enabled (Collection is enabled)
• Trigger (Collection is enabled and the ACS SHOULD now fetch the collected data) The Trigger value is only used for triggering the ACS to fetch the collected data and can only be used when FetchSamples is in the range [1:ReportSamples]. The transition from Enabled to Trigger to Enabled MUST be instantaneous and so will result in only a single value change for notification purposes.

Comma-separated list of unsigned integers. Each entry indicates the number of seconds during which data was collected during the sample interval. Individual SampleSeconds values can be less than SampleInterval, for several reasons, including:

TimeReference has been set to a time other than the Unknown Time and the current sample interval started part of the way through a scheduled sample interval.

ForceSample has been used to force statistics for the current sample to be calculated and updated in the data model.

Active Notification requests for this parameter MAY be denied.

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

The Agent MUST choose an initial value that doesn’t conflict with any existing entries.

Active Notification requests for this parameter MAY be denied.

Controls how this parameter’s value is sampled. Enumeration of:

• Current (Sampled value is current value)
• Change (Sampled value is change in value since start of sample interval) Parameters of non-numeric types can only support Current. The value of the SampleMode MUST be ignored for such parameters.

Controls how this parameter’s statistic is calculated from the sampled value(s). Enumeration of:

• Latest (Statistic is sampled value at end of sample interval)
• Minimum (Statistic is minimum sampled value during sample interval)
• Maximum (Statistic is maximum sampled value during sample interval)
• Average (Statistic is average (mean) sampled value during sample interval) Parameters of non-numeric types can only support Latest. The value of the CalculationMode MUST be ignored for such parameters. SampleMode MUST be applied before CalculationMode, i.e. the inputs to the calculation will have already accounted for SampleMode.

Comma-separated list of unsigned integers. Each entry indicates the number of seconds during which data was collected for this parameter during the sample interval. Individual SampleSeconds values can be less than PeriodicStatistics.SampleSet.{i}.SampleInterval, for several reasons, including:

Any of the reasons for which PeriodicStatistics.SampleSet.{i}.SampleSeconds values might be less than PeriodicStatistics.SampleSet.{i}.SampleInterval.

The parameter doesn’t exist, or was created or deleted during a sample interval.

Active Notification requests for this parameter MAY be denied.

Comma-separated list of unsigned integers (up to 1). Each entry is 0 if the sampled value is believed to be valid, or 1 if an event that might affect the validity of the sampled value occurred during the sample interval. For example, if the parameter value were to be reset during the sample interval then it would be appropriate to set SuspectData to 1.

Active Notification requests for this parameter MAY be denied.

Comma-separated list of strings. Each entry indicates the value of the referenced parameter, as determined by SampleMode, during the sample interval. The statistics values in this comma-separated lists MUST be in time order, with the oldest one first and the most recent one last. If the SampleMode parameter is not present, or is inappropriate for the referenced parameter, the statistics values MUST be collected in Current mode.

Active Notification requests for this parameter MAY be denied.

• “in range” : current value is greater than LowThreshold and less than HighThreshold.
• “out of range” : current value is less than or equal to LowThreshold, or greater than or equal to HighThreshold.
• “out of range (low)” : current value is less than or equal to LowThreshold.
• “out of range (high)” : current value is greater than or equal to HighThreshold. Note that, if LowThreshold and HighThreshold are both the same, the threshold/failure mechanism is disabled, so the value of this parameter will not increment. This parameter can be incremented at any time during a sample interval, and might be incremented more than once during a single sample interval. For this reason, the CPE SHOULD place a locally specified limit on the frequency at which it will notify the ACS of such changes, as described in [Section 3.2.1/TR-069a2]. Parameters of non-numeric types cannot support the threshold/failure mechanism. The value of this parameter MUST be ignored for such parameters.

The status of the announcement service.

Enumeration of:

• Disabled
• Enabled
• Error (MAY be used by the CPE to indicate a locally defined error condition, OPTIONAL)

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

The Agent MUST choose an initial value that doesn’t conflict with any existing entries.

Active Notification requests for this parameter MAY be denied.

The status of this group table entry.

Enumeration of:

• Disabled
• Enabled
• Error (MAY be used by the CPE to indicate a locally defined error condition, e.g. unable to parse received announcements, OPTIONAL)

The status of the query service.

Enumeration of:

• Disabled
• Enabled
• Error (MAY be used by the CPE to indicate a locally defined error condition, e.g. unable to contact query response server, OPTIONAL)

Indicates the status of this ExecEnv.

Enumeration of:

• Up
• Error (OPTIONAL)
• Disabled

1. All Deployment Units that were installed after the last “0 BOOTSTRAP” Inform event MUST be removed
2. All persistent storage, configuration files, and log files that were associated with the removed Deployment Units MUST be removed
3. Any Deployment Unit that is still installed against the Execution Environment MUST be restored to the version present when the last “0 BOOTSTRAP” Inform event was issued
4. Any Deployment Unit that was present when the last “0 BOOTSTRAP” Inform event was issued, but was subsequently uninstalled and is now not present, MUST be installed with the version that was present when the last “0 BOOTSTRAP” Inform event was issued
5. The Execution Environment MUST be restored to the version and configuration present when the last “0 BOOTSTRAP” Inform event was issued
6. The Execution Environment MUST be restarted after all other restoration requirements have been met

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced:

• Its value MUST NOT be empty.
• Its value MUST start with a letter.
• If its value is not assigned by the ACS, it MUST start with a “cpe-” prefix.
• The CPE MUST NOT change the parameter value.

Active Notification requests for this parameter MAY be denied.

The amount of disk space measured in kilobytes currently available to this ExecEnv. This value changes as the ExecutionUnit instances associated with this ExecEnv consumes disk space. A value of -1 MUST be used for ExecEnv instances where this parameter is not applicable.

Active Notification requests for this parameter MAY be denied.

The amount of physical RAM measured in kilobytes currently available to this ExecEnv. This value changes as the ExecutionUnit instances associated with this ExecEnv are started/stopped and consume the physical RAM. A value of -1 MUST be used for ExecEnv instances where this parameter is not applicable.

Active Notification requests for this parameter MAY be denied.

Comma-separated list of strings. Each list item MUST be the Path Name of a row in the ExecutionUnit. table. If the referenced object is deleted, the corresponding item MUST be removed from the list. Represents the ExecutionUnit instances currently running on this ExecEnv. This parameter only contains ExecutionUnit instances that currently have a ExecutionUnit.{i}.Status of Active.

Active Notification requests for this parameter MAY be denied.

[Alias] A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: