Broadband Forum

Component objects for CWMP: TR-069 Device:1.4 and

tr-157-1-1-0.xml

DATA MODEL DEFINITION

License

Copyright (c) 2009-2017, Broadband Forum

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

  1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
  3. Neither the name of the copyright holder nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The above license is used as a license under copyright only. Please reference the Forum IPR Policy for patent licensing terms https://www.broadband-forum.org/ipr-policy.

Any moral rights which are necessary to exercise under the above license grant are also deemed granted under this license.

Data Types

The Parameters defined in this specification make use of a limited subset of the default SOAP data types [SOAP1.1]. These data types and the named data types used by this specification are described below.

Note: A Parameter that is defined to be one of the named data types is reported as such at the beginning of the Parameter’s description via a reference back to the associated data type definition (e.g. [MACAddress]). However, such parameters still indicate their SOAP data types.

Data Type Base Type Description
base64 -

Base64 encoded binary (no line-length limitation).

A minimum and maximum allowed length can be indicated using the form base64(Min:Max), where Min and Max are the minimum and maximum length in characters before Base64 encoding. If either Min or Max are missing, this indicates no limit, and if Min is missing the colon can also be omitted, as in base64(Max). Multiple comma-separate ranges can be specified, in which case the length MUST be in one of the ranges.

boolean - Boolean, where the allowed values are 0 or 1 (or equivalently, true or false).
dateTime - The subset of the ISO 8601 date-time format defined by the SOAP dateTime type [SOAP1.1].
hexBinary -

Hex encoded binary.

A minimum and maximum allowed length can be indicated using the form hexBinary(Min:Max), where Min and Max are the minimum and maximum length in characters before Hex Binary encoding. If either Min or Max are missing, this indicates no limit, and if Min is missing the colon can also be omitted, as in hexBinary(Max). Multiple comma-separated ranges can be specified, in which case the length MUST be in one of the ranges.

int -

Integer in the range -2147483648 to +2147483647, inclusive.

For some int types, a value range is given using the form int(Min:Max) or int(Min:Max step Step) where the Min and Max values are inclusive. If either Min or Max are missing, this indicates no limit. If Step is missing, this indicates a step of 1. Multiple comma-separated ranges can be specified, in which case the value will be in one of the ranges.

string - For strings, a minimum and maximum allowed length can be indicated using the form string(Min:Max), where Min and Max are the minimum and maximum string length in characters. If either Min or Max are missing, this indicates no limit, and if Min is missing the colon can also be omitted, as in string(Max). Multiple comma-separated ranges can be specified, in which case the string length will be in one of the ranges.
unsignedInt -

Unsigned integer in the range 0 to 4294967295, inclusive.

For some unsignedInt types, a value range is given using the form unsignedInt(Min:Max) or unsigned(Min:Max step Step), where the Min and Max values are inclusive. If either Min or Max are missing, this indicates no limit. If Step is missing, this indicates a step of 1. Multiple comma-separated ranges can be specified, in which case the value will be in one of the ranges.

IPAddress string(:45)

IP address, i.e. IPv4 address (or IPv4 subnet mask) or IPv6 address.

All IPv4 addresses and subnet masks MUST be represented as strings in IPv4 dotted-decimal notation. Here are some examples of valid IPv4 address textual representations:

  • 216.52.29.100
  • 192.168.1.254

All IPv6 addresses MUST be represented using any of the 3 standard textual representations defined in [RFC4291] Sections 2.2.1, 2.2.2 and 2.2.3. Both lower-case and upper-case letters can be used, but use of lower-case letters is RECOMMENDED. Here are some examples of valid IPv6 address textual representations:

  • 1080:0:0:800:ba98:3210:11aa:12dd
  • 1080::800:ba98:3210:11aa:12dd
  • 0:0:0:0:0:0:13.1.68.3

IPv6 addresses MUST NOT include zone identifiers. Zone identifiers are discussed in [Section 6/RFC4007].

Unspecified or inapplicable addresses (or IPv4 subnet masks) MUST be represented as empty strings unless otherwise specified by the parameter definition.

MACAddress string(:17)

All MAC addresses are represented as strings of 12 hexadecimal digits (digits 0-9, letters A-F or a-f) displayed as six pairs of digits separated by colons. Unspecified or inapplicable MAC addresses MUST be represented as empty strings unless otherwise specified by the parameter definition.

Possible patterns:

  • <Empty> (an empty string)
  • ([0-9A-Fa-f][0-9A-Fa-f]:){5}([0-9A-Fa-f][0-9A-Fa-f])

References

[802.1D-2004] IEEE Std 802.1D-2004, Media Access Control (MAC) Bridges, IEEE, 2004.
[802.1Q-2005] IEEE Std 802.1Q-2005, Virtual Bridged Local Area Networks, IEEE, 2006.
[BLUE] Blue, A New Class of Active Queue Management Algorithms.
[DLNA-NDIG] DLNA Networked Device Interoperability Guidelines, DLNA Networked Device Interoperability Guidelines, Volume 2: Media Format Profiles., DLNA, October 2006.
[DVB-TS.102.824] TS 102 824, Digital Video Broadcasting (DVB);Remote Management and Firmware Update System for DVB IP Services, ETSI, July 2008.
[HTML4.01] HTML 4.01 Specification, W3C.
[IANA-uri-schemes] IANA Uniform Resource Identifier (URI) Schemes Registry, Uniform Resource Identifier (URI) Schemes, IANA.
[ICSA-Firewall] ICSA Modular Firewall Certification Criteria, Required Services Security Policy - Small/Medium Business (SMB) Category module - version 4.0, ICSA Labs.
[IEEE_EUI64] Guidelines for 64-bit Global Identifier (EUI-64) Registration Authority, Guidelines for 64-bit Global Identifier (EUI-64) Registration Authority, IEEE, March 1997.
[ISO-13818-6:1998] ISO/IEC 13818-6:1998, Information Technology - Generic coding of moving pictures and associated audio information - Part 6: Extensions for DSM-CC, ISO, 1998.
[OUI] Organizationally Unique Identifiers (OUIs).
[RED] References on RED (Random Early Detection) Queue Management.
[RFC1323] RFC 1323, TCP Extensions for High Performance, IETF, May 1992.
[RFC2131] RFC 2131, Dynamic Host Configuration Protocol, IETF.
[RFC2132] RFC 2132, DHCP Options and BOOTP Vendor Extensions, IETF.
[RFC2225] RFC 2225, Classical IP and ARP over ATM, IETF.
[RFC2474] RFC 2474, Definition of the Differentiated Services Field (DS Field) in the IPv4 and IPv6 Headers, IETF.
[RFC2516] RFC 2516, A Method for Transmitting PPP Over Ethernet (PPPoE), IETF.
[RFC2581] RFC 2581, TCP Congestion Control, IETF, April 1999.
[RFC2582] RFC 2582, The NewReno Modification to TCP’s Fast Recovery Algorithm, IETF, April 1999.
[RFC2616] RFC 2616, Hypertext Transfer Protocol - HTTP/1.1, IETF, 1999.
[RFC2634] RFC 2634, Enhanced Security Services for S/MIME, IETF.
[RFC2662] RFC 2662, Definitions of Managed Objects for the ADSL Lines, IETF.
[RFC2684] RFC 2684, Multiprotocol Encapsulation over ATM Adaptation Layer 5, IETF.
[RFC2697] RFC 2697, A Single Rate Three Color Marker, IETF.
[RFC2698] RFC 2698, A Two Rate Three Color Marker, IETF.
[RFC2818] RFC 2818, HTTP Over TLS, IETF, May 2000.
[RFC2898] RFC 2898, PKCS #5: Password-Based Cryptography Specification Version 2.0, IETF.
[RFC2974] RFC 2974, Session Announcement Protocol, IETF, October 2000.
[RFC3004] RFC 3004, The User Class Option for DHCP, IETF.
[RFC3066] RFC 3066, Tags for the Identification of Languages, IETF.
[RFC3489] RFC 3489, STUN - Simple Traversal of User Datagram Protocol (UDP) Through Network Address Translators (NATs), IETF.
[RFC3925] RFC 3925, Vendor-Identifying Vendor Options for Dynamic Host Configuration Protocol version 4 (DHCPv4), IETF.
[RFC3926] RFC 3926, FLUTE - File Delivery over Unidirectional Transport, IETF, October 2004.
[RFC3986] RFC 3986, Uniform Resource Identifier (URI): Generic Syntax, IETF.
[RFC4007] RFC 4007, IPv6 Scoped Address Architecture, IETF.
[RFC4122] RFC 4122, A Universally Unique IDentifier (UUID) URN Namespace, IETF, 2005.
[RFC4291] RFC 4291, IP Version 6 Addressing Architecture, IETF, 2006.
[RFC4632] RFC 4632, Classless Inter-domain Routing (CIDR): The Internet Address Assignment and Aggregation Plan, IETF, 2006.
[RFC7159] RFC7159, The JavaScript Object Notation (JSON) Data Interchange Format, IETF, March 2014.
[RFC7230] RFC 7230, Hypertext Transfer Protocol (HTTP/1.1): Message Syntax and Routing, IETF, June 2014.
[RFC7252] RFC 7252, The Constrained Application Protocol (CoAP), IETF, June 2014.
[RFC793] RFC 793, Transmission Control Protocol, IETF, September 1981.
[RFC8141] RFC 8141, Uniform Resource Names (URNs), IETF, April 2017.
[RFC862] RFC 862, Echo Protocol, IETF, 1983.
[SOAP1.1] Simple Object Access Protocol (SOAP) 1.1, W3C.
[TR-069] TR-069 Amendment 6, CPE WAN Management Protocol, Broadband Forum, April 2018.
[TR-069a2] TR-069 Amendment 2, CPE WAN Management Protocol, Broadband Forum, December 2007.
[TR-098a1] TR-098 Amendment 1, Internet Gateway Device Data Model for TR-069, Broadband Forum, December 2006.
[TR-098a2] TR-098 Amendment 2, Internet Gateway Device Data Model for TR-069, Broadband Forum, September 2008.
[TR-106a1] TR-106 Amendment 1, Data Model Template for TR-069-Enabled Devices, Broadband Forum, November 2006.
[TR-106a2] TR-106 Amendment 2, Data Model Template for TR-069-Enabled Devices, Broadband Forum, November 2008.
[TR-106a3] TR-106 Amendment 3, Data Model Template for TR-069-Enabled Devices, Broadband Forum, September 2009.
[TR-143] TR-143 Amendment 1 Corrigendum 1, Enabling Network Throughput Performance Tests and Statistical Monitoring, Broadband Forum, August 2015.
[TR-157] TR-157 Amendment 10, Component Objects for CWMP, Broadband Forum, November 2015.
[UPnP-DAv1] UPnP Device Architecture, UPnP Device Architecture 1.0, UPnP Forum, April 2008.
[USB1.0] USB 1.0, USB 1.0 Specification, USB-IF, January 1996.
[USB2.0] USB 2.0, USB 2.0 Specification, USB-IF, April 2000.
[USB3.0] USB 3.0, USB 3.0 Specification, USB-IF, November 2008.
[WPSv1.0] Wi-Fi Protected Setup Specification Version 1.0h, Wi-Fi Alliance, 2006.
[ZigBee2007] ZigBee 2007 Specification, ZigBee 2007 Specification, ZigBee Alliance, October 2007.

Legend

Object definition.
Parameter definition.

InternetGatewayDevice:1.6 Data Model

For a given implementation of this data model, the Agent MUST indicate support for the highest version number of any object or parameter that it supports. For example, even if the Agent supports only a single parameter that was introduced in version 1.4, then it will indicate support for version 1.4. The version number associated with each object and parameter is shown in the Version column.

Name Type Write Description Object Default Version
InternetGatewayDevice. object R The top-level object for an Internet Gateway Device. - 1.0
DeviceSummary string(:1024) R

As defined in [TR-106a1].

This parameter is DEPRECATED because DeviceInfo.SupportedDataModel and associated Device Type XML documents (DT Instances) provide a more granular and scalable way of describing the device’s data model. Therefore its value MAY be an empty string if (and only if) DeviceInfo.SupportedDataModel is supported.

This parameter MUST always be included in Inform messages.

- 1.0
LANDeviceNumberOfEntries unsignedInt R Number of instances of LANDevice. - 1.0
WANDeviceNumberOfEntries unsignedInt R Number of instances of WANDevice. - 1.0
UserNumberOfEntries unsignedInt R Number of entries in the User table. - 1.0
SmartCardReaderNumberOfEntries unsignedInt R Number of entries in the SmartCardReader table. - 1.0
InternetGatewayDevice.Services. object R This object contains general services information. - 1.0
InternetGatewayDevice.DeviceInfo. object R This object contains general device information. - 1.0
Manufacturer string(:64) R The manufacturer of the CPE (human readable string). - 1.0
ManufacturerOUI string(:6) R

Organizationally unique identifier of the device manufacturer. Represented as a six hexadecimal-digit value using all upper-case letters and including any leading zeros. The value MUST be a valid OUI as defined in [OUI].

This value MUST remain fixed over the lifetime of the device, including across firmware updates.

- 1.0
ModelName string(:64) R Model name of the CPE (human readable string). - 1.0
Description string(:256) R A full description of the CPE device (human readable string). - 1.0
ProductClass string(:64) R

Identifier of the class of product for which the serial number applies. That is, for a given manufacturer, this parameter is used to identify the product or class of product over which the SerialNumber parameter is unique.

This value MUST remain fixed over the lifetime of the device, including across firmware updates.

- 1.0
SerialNumber string(:64) R

Serial number of the CPE.

This value MUST remain fixed over the lifetime of the device, including across firmware updates.

- 1.0
HardwareVersion string(:64) R

A string identifying the particular CPE model and version.

This parameter MUST always be included in Inform messages.

- 1.0
SoftwareVersion string(:64) R

A string identifying the software version currently installed in the CPE. To allow version comparisons, this element SHOULD be in the form of dot-delimited integers, where each successive integer represents a more minor category of variation. For example, 3.0.21 where the components mean: Major.Minor.Build.

This parameter MUST always be included in Inform messages.

Active Notification MUST always be enabled for this parameter.

- 1.0
ModemFirmwareVersion string(:64) R A string identifying the version of the modem firmware currently installed in the CPE. This is applicable only when the modem firmware is separable from the overall CPE software. - 1.0
EnabledOptions string[](:1024) R Comma-separated list (maximum number of characters 1024) of strings. The OptionName of each Option that is currently enabled in the CPE. The OptionName of each is identical to the OptionName element of the OptionStruct described in [TR-069a2]. Only those options are listed whose State indicates the option is enabled. - 1.0
AdditionalHardwareVersion string[](:64) R Comma-separated list (maximum number of characters 64) of strings. Any additional hardware version information the vendor might wish to supply. - 1.0
AdditionalSoftwareVersion string[](:64) R Comma-separated list (maximum number of characters 64) of strings. Any additional software version information the vendor might wish to supply. - 1.0
SpecVersion string(:16) R

Represents the version of the specification implemented by the device. Currently 1.0 is the only available version. The value of this parameter MUST equal “1.0”. This parameter is DEPRECATED because its value is fixed and it therefore serves no purpose. However, it is a Forced Inform parameter and therefore cannot be OBSOLETED.

This parameter MUST always be included in Inform messages.

1.0 1.0
ProvisioningCode string(:64) W

Identifier of the primary service provider and other provisioning information, which MAY be used by the ACS to determine service provider-specific customization and provisioning parameters. If not an empty string, this argument SHOULD be in the form of a hierarchical descriptor with one or more nodes specified. Each node in the hierarchy is represented as a 4-character sub-string, containing only numerals or upper-case letters. If there is more than one node indicated, each node is separated by a “.” (dot). Examples: “TLCO” or “TLCO.GRP2”.

This parameter MUST always be included in Inform messages.

Active Notification MUST always be enabled for this parameter.

- 1.0
UpTime unsignedInt R

Time in seconds since the CPE was last restarted.

Active Notification requests for this parameter MAY be denied.

- 1.0
FirstUseDate dateTime R

Date and time in UTC that the CPE first both successfully established an IP-layer network connection and acquired an absolute time reference using NTP or equivalent over that network connection. The CPE MAY reset this date after a factory reset.

If NTP or equivalent is not available, this parameter, if present, SHOULD be set to the Unknown Time value.

- 1.0
DeviceLog string(:32768) R

Vendor-specific log(s).

Active Notification requests for this parameter MAY be denied.

- 1.0
VendorConfigFileNumberOfEntries unsignedInt R Number of instances of VendorConfigFile. - 1.0
SupportedDataModelNumberOfEntries unsignedInt R Number of entries in the SupportedDataModel table. - 1.0
InternetGatewayDevice.DeviceInfo.VendorConfigFile.{i}. object(0:) R

Every instance of this object is a Vendor Configuration File, and contains parameters associated with the Vendor Configuration File.

This table of Vendor Configuration Files is for information only and does not allow the ACS to operate on these files in any way. Whenever the CPE successfully downloads a configuration file as a result of the Download RPC with the FileType argument of 3 Vendor Configuration File, the CPE MUST update this table. If the name of the file (determined as described in the definition of the Name parameter) differs from that of any existing instance, then the CPE MUST create a new instance to represent this file. If instead, the name of the file is identical to that of an existing instance, then the CPE MUST update the content of the existing instance with the new version, date, and (optionally) description of the file.

- 1.0
Name string(:64) R

Name of the vendor configuration file.

If the CPE is able to obtain the name of the configuration file from the file itself, then the value of this parameter MUST be set to that name. Otherwise, if the CPE can extract the file name from the URL used to download the configuration file, then the value of this parameter MUST be set to that name. Otherwise, the value of this parameter MUST be set to the value of the TargetFileName argument of the Download RPC used to download this configuration file.

- 1.0
Version string(:16) R

A string identifying the configuration file version currently used in the CPE.

If the CPE is able to obtain the version of the configuration file from the file itself, then the value of this parameter MUST be set to the obtained value. Otherwise, the value of this parameter MUST be an empty string.

- 1.0
Date dateTime R Date and time when the content of the current version of this vendor configuration file was first applied by the CPE. - 1.0
Description string(:256) R A description of the vendor configuration file (human-readable string). - 1.0
InternetGatewayDevice.DeviceInfo.MemoryStatus. object R Status of the device’s volatile physical memory. - 1.0
Total unsignedInt R The total physical RAM, in kilobytes, installed on the device. - 1.0
Free unsignedInt R

The free physical RAM, in kilobytes, currently available on the device.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.DeviceInfo.ProcessStatus. object R Status of the processes on the device. - 1.0
CPUUsage unsignedInt(:100) R

The total amount of the CPU, in percent, rounded up to the nearest whole percent. In the case that multiple CPU are present, this value represents the average of all CPU.

Active Notification requests for this parameter MAY be denied.

- 1.0
ProcessNumberOfEntries unsignedInt R Number of entries in the Process table. Since a Process can come and go very quickly, the CPE SHOULD place a locally specified limit on the frequency at which it will notify the ACS of value changes, as described in [Section 3.2.1/TR-069a2]. - 1.0
InternetGatewayDevice.DeviceInfo.ProcessStatus.Process.{i}. object(0:) R

List of all processes running on the device.

At most one entry in this table can exist with a given value for PID.

- 1.0
PID unsignedInt R The Process Identifier. - 1.0
Command string(:256) R The name of the command that has caused the process to exist. - 1.0
Size unsignedInt R

The size in kilobytes of the memory occupied by the process.

Active Notification requests for this parameter MAY be denied.

- 1.0
Priority unsignedInt(:99) R The priority of the process where 0 is highest. - 1.0
CPUTime unsignedInt R

The amount of time in milliseconds that the process has spent taking up CPU time since the process was started.

Active Notification requests for this parameter MAY be denied.

- 1.0
State string R

The current state that the process is in.

Enumeration of:

  • Running
  • Sleeping
  • Stopped
  • Idle (OPTIONAL)
  • Uninterruptible (OPTIONAL)
  • Zombie (OPTIONAL)

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.DeviceInfo.TemperatureStatus. object R Status of the temperature of the device. - 1.0
TemperatureSensorNumberOfEntries unsignedInt R Number of entries in TemperatureSensor table. - 1.0
InternetGatewayDevice.DeviceInfo.TemperatureStatus.TemperatureSensor.{i}. object(0:) R

This object represents information that the device has obtained via sampling an internal temperature sensor.

At most one entry in this table can exist with a given value for Name.

- 1.0
Enable boolean W Indicates whether or not the temperature sensor is enabled. - 1.0
Status string R

The status of this temperature sensor.

Enumeration of:

  • Disabled (The sensor is not currently sampling the temperature)
  • Enabled (The sensor is currently sampling the temperature)
  • Error (The sensor error currently prevents sampling the temperature)
- 1.0
Reset boolean W

When set to true, resets the temperature sensor.

When read, this parameter returns false, regardless of the actual value.

- 1.0
ResetTime dateTime R The time at which this temperature sensor was reset. Reset can be caused by:
  • Status transition from Disabled to Enabled
  • Reset set to true.
  • An internal reset of the temperature sensor (including a reboot of the device). The Unknown Time value, as defined in [TR-106a2], indicates that this temperature sensor has never been reset, which can only happen if it has never been enabled.
- 1.0
Name string(:256) R Name of this temperature sensor. This text MUST be sufficient to distinguish this temperature sensor from other temperature sensors. - 1.0
Value int(-274:) R

This temperature sensor’s last good reading in degrees celsius. A value of -274 (which is below absolute zero) indicates a good reading has not been obtained since last reset.

Active Notification requests for this parameter MAY be denied.

- 1.0
LastUpdate dateTime R

The time at which this temperature sensor’s last good reading was obtained. The Unknown Time value, as defined in [TR-106a2], indicates a good reading has not been obtained since last reset.

Active Notification requests for this parameter MAY be denied.

- 1.0
MinValue int(-274:) R This temperature sensor’s lowest value reading in degrees celsius since last reset. A value of -274 (which is below absolute zero) indicates a good reading has not been obtained since last reset. - 1.0
MinTime dateTime R The time at which this temperature sensor’s lowest value was read. The Unknown Time value, as defined in [TR-106a2], indicates a good reading has not been obtained since last reset. - 1.0
MaxValue int(-274:) R This temperature sensor’s highest value reading in degrees celsius since last reset. A value of -274 (which is below absolute zero) indicates a good reading has not been obtained since last reset. - 1.0
MaxTime dateTime R The time at which this temperature sensor’s highest value was read. The Unknown Time value, as defined in [TR-106a2], indicates a good reading has not been obtained since last reset. - 1.0
LowAlarmValue int(-274:) W This temperature sensor’s low alarm value in degrees celsius. A value of -274 (which is below absolute zero) indicates a non configured value. - 1.0
LowAlarmTime dateTime R Initial time at which this temperature sensor’s LowAlarmValue was encountered. This value is only set the first time the alarm is seen and not changed until the next reset. The Unknown Time value, as defined in [TR-106a2], indicates that an alarm has not been encountered since the last reset. - 1.0
HighAlarmValue int(-274:) W This temperature sensor’s high alarm value in degrees celsius. A value of -274 (which is below absolute zero) indicates a non configured value. - 1.0
HighAlarmTime dateTime R Initial time at which this temperature sensor’s HighAlarmValue was encountered. This value is only set the first time the alarm is seen and not changed until the next reset. The Unknown Time value, as defined in [TR-106a2], indicates that an alarm has not been encountered since the last reset. - 1.0
InternetGatewayDevice.DeviceInfo.NetworkProperties. object R This object defines the parameters that describe how the device handles network traffic. - 1.0
MaxTCPWindowSize unsignedInt R The maximum number of bytes of outstanding data a sender can send on a particular connection prior to an acknowledgment [RFC793]. Any scaling factor SHOULD be included in this parameter [RFC1323]. - 1.0
TCPImplementation string[] R

Comma-separated list of strings. Indicates the TCP congestion control mechanism(s) implemented. Each list item is an enumeration of:

  • Tahoe (Represents the base TCP implementation in [RFC793] and elements of [RFC2582])
  • Reno (Represents the base TCP implementation in [RFC793] with the additional algorithms defined in [RFC2581])
  • New Reno (Described as a modification to the Reno algorithms in [RFC2582])
  • Vegas (An emerging TCP congestion control mechanism) Tahoe, Reno, and New Reno are defined in [RFC2582]
- 1.0
InternetGatewayDevice.DeviceInfo.SupportedDataModel.{i}. object(0:) R

This table contains details of the device’s Current Supported Data Model. The table MUST describe the device’s entire Supported Data Model. Therefore, if a device’s Supported Data Model changes at run-time, entries will need to be added or removed as appropriate. Each table entry MUST refer to only a single Root Object or Service Object. The device MAY choose to use more than one table entry for a given Root Object or Service Object. Considering that every device has some form of a data model, this table MUST NOT be empty.

At most one entry in this table can exist with a given value for URL.

- 1.0
URL string(:256) R URL ([RFC3986]) that describes some or all of the device’s Current Supported Data Model. The URL MUST reference an XML file which describes the appropriate part of the Supported Data Model. The referenced XML file MUST be compliant with the DT (Device Type) Schema that is described in [Annex B/TR-106a3], including any additional normative requirements referenced within the Schema. The XML file referenced by this URL MUST NOT change while the CPE is running, and SHOULD NOT change across a CPE reboot. Note that, if the same XML file is to be used for multiple CPE, this strongly suggests that the XML file referenced by this URL should never change. The URL MAY permit the XML file to be accessed at run-time, in which case, the XML file MAY be located within the CPE. Behavior in the event of an invalid URL, failure to access the referenced XML file, or an invalid XML file, is implementation-dependent. - 1.0
URN string(:256) R URN ([RFC3986]) that is the value of the spec attribute in the DM (data model) Instance that defines the Root Object or Service Object referenced by this table entry. For example, if this table entry references a DT Instance that refers to the Device:1.3 Root Object, the value of this parameter would be urn:broadband-forum-org:tr-157-1-0-0, because TR-157 defines Device:1.3. If the DT Instance instead referred to a vendor-specific Root Object, e.g. X_EXAMPLE_Device:1.0 (derived from Device:1.3), the value of this parameter would be something like urn:example-com:device-1-0-0. - 1.0
Features string[] R

Comma-separated list of strings. This parameter MUST list exactly the features that are defined using the top-level feature element in the DT Instance referenced by URL. For example, if the DT instance specified the following:

then the value of this parameter might be DNSServer,Router,X_MyDeviceFeature. The order in which the features are listed is not significant.

- 1.0
InternetGatewayDevice.DeviceConfig. object R This object contains general configuration parameters. - 1.0
PersistentData string(:256) W Arbitrary user data that MUST persist across CPE reboots. - 1.0
ConfigFile string(:32768) W

A dump of the currently running configuration on the CPE. This parameter enables the ability to backup and restore the last known good state of the CPE. It returns a vendor-specific document that defines the state of the CPE. The document MUST be capable of restoring the CPE’s state when written back to the CPE using SetParameterValues.

An alternative to this parameter, e.g. when the configuration file is larger than the parameter size limit, is to use the Upload and Download RPCs with a FileType of 1 Vendor Configuration File.

- 1.0
InternetGatewayDevice.ManagementServer. object R This object contains parameters relating to the CPE’s association with an ACS. - 1.0
EnableCWMP boolean W Enables and disables the CPE’s support for CWMP. false means that CWMP support in the CPE is disabled, in which case the device MUST NOT send any Inform messages to the ACS or accept any Connection Request notifications from the ACS. true means that CWMP support on the CPE is enabled. The factory default value MUST be true. The subscriber can re-enable the CPE’s CWMP support either by performing a factory reset or by using a LAN-side protocol to change the value of this parameter back to true. - 1.0
URL string(:256) W URL, as defined in [RFC3986], for the CPE to connect to the ACS using the CPE WAN Management Protocol. This parameter MUST be in the form of a valid HTTP or HTTPS URL [RFC2616]. The host portion of this URL is used by the CPE for validating the ACS certificate when using SSL or TLS. Note that on a factory reset of the CPE, the value of this parameter might be reset to its factory value. If an ACS modifies the value of this parameter, it SHOULD be prepared to accommodate the situation that the original value is restored as the result of a factory reset. - 1.0
Username string(:256) W

Username used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This username is used only for HTTP-based authentication of the CPE.

Note that on a factory reset of the CPE, the value of this parameter might be reset to its factory value. If an ACS modifies the value of this parameter, it SHOULD be prepared to accommodate the situation that the original value is restored as the result of a factory reset.

- 1.0
Password string(:256) W

Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This password is used only for HTTP-based authentication of the CPE.

Note that on a factory reset of the CPE, the value of this parameter might be reset to its factory value. If an ACS modifies the value of this parameter, it SHOULD be prepared to accommodate the situation that the original value is restored as the result of a factory reset.

When read, this parameter returns an empty string, regardless of the actual value.

- 1.0
PeriodicInformEnable boolean W Whether or not the CPE MUST periodically send CPE information to the ACS using the Inform method call. - 1.0
PeriodicInformInterval unsignedInt(1:) W The duration in seconds of the interval for which the CPE MUST attempt to connect with the ACS and call the Inform method if PeriodicInformEnable is true. - 1.0
PeriodicInformTime dateTime W An absolute time reference in UTC to determine when the CPE will initiate the periodic Inform method calls. Each Inform call MUST occur at this reference time plus or minus an integer multiple of the PeriodicInformInterval. PeriodicInformTime is used only to set the “phase” of the periodic Informs. The actual value of PeriodicInformTime can be arbitrarily far into the past or future. For example, if PeriodicInformInterval is 86400 (a day) and if PeriodicInformTime is set to UTC midnight on some day (in the past, present, or future) then periodic Informs will occur every day at UTC midnight. These MUST begin on the very next midnight, even if PeriodicInformTime refers to a day in the future. The Unknown Time value defined in [Section 2.2/TR-098a2] indicates that no particular time reference is specified. That is, the CPE MAY locally choose the time reference, and needs only to adhere to the specified PeriodicInformInterval. If absolute time is not available to the CPE, its periodic Inform behavior MUST be the same as if the PeriodicInformTime parameter was set to the Unknown Time value. - 1.0
ParameterKey string(:32) R

ParameterKey provides the ACS a reliable and extensible means to track changes made by the ACS. The value of ParameterKey MUST be equal to the value of the ParameterKey argument from the most recent successful SetParameterValues, AddObject, or DeleteObject method call from the ACS. The CPE MUST set ParameterKey to the value specified in the corresponding method arguments if and only if the method completes successfully and no fault response is generated. If a method call does not complete successfully (implying that the changes requested in the method did not take effect), the value of ParameterKey MUST NOT be modified. The CPE MUST only modify the value of ParameterKey as a result of SetParameterValues, AddObject, DeleteObject, or due to a factory reset. On factory reset, the value of ParameterKey MUST be set to an empty string.

This parameter MUST always be included in Inform messages.

Active Notification requests for this parameter MAY be denied.

- 1.0
ConnectionRequestURL string(:256) R

HTTP URL, as defined in [RFC3986], for an ACS to make a Connection Request notification to the CPE. In the form: http://host:port/path The host portion of the URL MAY be the IP address for the management interface of the CPE in lieu of a host name.

This parameter MUST always be included in Inform messages.

Active Notification MUST by default be enabled for this parameter.

- 1.0
ConnectionRequestUsername string(:256) W Username used to authenticate an ACS making a Connection Request to the CPE. - 1.0
ConnectionRequestPassword string(:256) W

Password used to authenticate an ACS making a Connection Request to the CPE.

When read, this parameter returns an empty string, regardless of the actual value.

- 1.0
UpgradesManaged boolean W Indicates whether or not the ACS will manage upgrades for the CPE. If true, the CPE SHOULD NOT use other means other than the ACS to seek out available upgrades. If false, the CPE MAY use other means for this purpose. Note that an autonomous upgrade (reported via an 10 AUTONOMOUS TRANSFER COMPLETE Inform Event code) SHOULD be regarded as a managed upgade if it is performed according to ACS-specified policy. - 1.0
KickURL string(:256) R Present only for a CPE that supports the Kicked RPC method. LAN-accessible URL, as defined in [RFC3986], from which the CPE can be “kicked” to initiate the Kicked RPC method call. MUST be an absolute URL including a host name or IP address as would be used on the LAN side of the CPE. - 1.0
DownloadProgressURL string(:256) R Present only for a CPE that provides a LAN-side web page to show progress during a file download. LAN-accessible URL, as defined in [RFC3986], to which a web-server associated with the ACS MAY redirect a user’s browser on initiation of a file download to observer the status of the download. - 1.0
DefaultActiveNotificationThrottle unsignedInt W This parameter is used to control throttling of active notifications sent by the CPE to the ACS. It defines the minimum number of seconds that the CPE MUST wait since the end of the last session with the ACS before establishing a new session for the purpose of delivering an active notification. In other words, if CPE needs to establish a new session with the ACS for the sole purpose of delivering an active notification, it MUST delay establishing such a session as needed to ensure that the minimum time since the last session completion has been met. The time is counted since the last successfully completed session, regardless of whether or not it was used for active notifications or other purposes. However, if connection to the ACS is established for purposes other than just delivering active notifications, including for the purpose of retrying a failed session, such connection MUST NOT be delayed based on this parameter value, and the pending active notifications MUST be communicated during that connection. The time of the last session completion does not need to be tracked across reboots. - 1.0
UDPConnectionRequestAddress string(:256) R

Address and port to which an ACS MAY send a UDP Connection Request to the CPE (see [Annex G/TR-069a2]). This parameter is represented in the form of an Authority element as defined in [RFC3986]. The value MUST be in one of the following two forms:

host:port
host When STUNEnable is true, the host and port portions of this parameter MUST represent the public address and port corresponding to the NAT binding through which the ACS can send UDP Connection Request messages (once this information is learned by the CPE through the use of STUN). When STUNEnable is false, the host and port portions of the URL MUST represent the local IP address and port on which the CPE is listening for UDP Connection Request messages. The second form of this parameter MAY be used only if the port value is equal to “80”.
- 1.0
UDPConnectionRequestAddressNotificationLimit unsignedInt W The minimum time, in seconds, between Active Notifications resulting from changes to the UDPConnectionRequestAddress (if Active Notification is enabled). - 1.0
STUNEnable boolean W Enables or disables the use of STUN by the CPE. This applies only to the use of STUN in association with the ACS to allow UDP Connection Requests. - 1.0
STUNServerAddress string(:256) W Host name or IP address of the STUN server for the CPE to send Binding Requests if STUN is enabled via STUNEnable. If an empty string and STUNEnable is true, the CPE MUST use the address of the ACS extracted from the host portion of the ACS URL. - 1.0
STUNServerPort unsignedInt(0:65535) W Port number of the STUN server for the CPE to send Binding Requests if STUN is enabled via STUNEnable. By default, this SHOULD be the equal to the default STUN port, 3478. - 1.0
STUNUsername string(:256) W If not an empty string, the value of the STUN USERNAME attribute to be used in Binding Requests (only if message integrity has been requested by the STUN server). If an empty string, the CPE MUST NOT send STUN Binding Requests with message integrity. - 1.0
STUNPassword string(:256) W

The value of the STUN Password to be used in computing the MESSAGE-INTEGRITY attribute to be used in Binding Requests (only if message integrity has been requested by the STUN server).

When read, this parameter returns an empty string, regardless of the actual value.

- 1.0
STUNMaximumKeepAlivePeriod int(-1:) W If STUN Is enabled, the maximum period, in seconds, that STUN Binding Requests MUST be sent by the CPE for the purpose of maintaining the binding in the Gateway. This applies specifically to Binding Requests sent from the UDP Connection Request address and port. A value of -1 indicates that no maximum period is specified. - 1.0
STUNMinimumKeepAlivePeriod unsignedInt W If STUN Is enabled, the minimum period, in seconds, that STUN Binding Requests can be sent by the CPE for the purpose of maintaining the binding in the Gateway. This limit applies only to Binding Requests sent from the UDP Connection Request address and port, and only those that do not contain the BINDING-CHANGE attribute. This limit does not apply to retransmissions following the procedures defined in [RFC3489]. - 1.0
NATDetected boolean R When STUN is enabled, this parameter indicates whether or not the CPE has detected address and/or port mapping in use. A true value indicates that the received MAPPED-ADDRESS in the most recent Binding Response differs from the CPE’s source address and port. When STUNEnable is false, this value MUST be false. - 1.0
ManageableDeviceNumberOfEntries unsignedInt R Number of entries in the ManageableDevice table. - 1.0
ManageableDeviceNotificationLimit unsignedInt W The minimum time, in seconds, between Active Notifications resulting from changes to the ManageableDeviceNumberOfEntries (if Active Notification is enabled). - 1.0
InternetGatewayDevice.ManagementServer.ManageableDevice.{i}. object(0:) R

Each entry in this table corresponds to a distinct LAN Device that supports Device-Gateway Association according to [Annex F/TR-069a2] as indicated by the presence of the DHCP option specified in that Annex.

At most one entry in this table can exist with the same values for all of ManufacturerOUI, SerialNumber and ProductClass.

- 1.0
ManufacturerOUI string(:6) R

Organizationally unique identifier of the Device manufacturer as provided to the Gateway by the Device. Represented as a six hexadecimal-digit value using all upper-case letters and including any leading zeros. The value MUST be a valid OUI as defined in [OUI].

Active Notification requests for this parameter MAY be denied.

- 1.0
SerialNumber string(:64) R

Serial number of the Device as provided to the Gateway by the Device.

Active Notification requests for this parameter MAY be denied.

- 1.0
ProductClass string(:64) R

Identifier of the class of product for which the Device’s serial number applies as provided to the Gateway by the Device. If the Device does not provide a Product Class, then this parameter MUST be an empty string.

Active Notification requests for this parameter MAY be denied.

- 1.0
Host string[](:1024) R Comma-separated list (maximum number of characters 1024) of strings. Each list item MUST be the Path Name of a Host table row. If the referenced object is deleted, the corresponding item MUST be removed from the list. This list MUST include an item for each Host table entry, whether active or inactive, that corresponds to this physical LAN Device. As such entries are added to or removed from the Host tables, the value of this parameter MUST be updated accordingly. For example: InternetGatewayDevice.LANDevice.1.Hosts.Host.1,InternetGatewayDevice.LANDevice.1.Hosts.Host.5 - 1.0
InternetGatewayDevice.ManagementServer.AutonomousTransferCompletePolicy. object R This object allows configuration of CPE policy for notification of AUTONOMOUS TRANSFER COMPLETE events, defined in [TR-069a2]. The CPE policy determines the conditions under which the CPE notifies the ACS of the completion of file transfers that were not specifically requested by the ACS. - 1.0
Enable boolean W Enable/disable CPE notification of AUTONOMOUS TRANSFER COMPLETE events to the ACS. - 1.0
TransferTypeFilter string W

Indicates the transfer types that MUST be included when the CPE notifies the ACS of AUTONOMOUS TRANSFER COMPLETE events. Transfer types not indicated by this filter MUST NOT be included when the CPE notifies the ACS. Enumeration of:

  • Upload
  • Download
  • Both (Upload and Download) Note that this includes any backup or restore operations that were not specifically requested by the ACS. A backup is regarded as an Upload and a restore is regarded as a Download.
- 1.0
FileTypeFilter string[](:1024) W

Comma-separated list (maximum number of characters 1024) of strings. Indicates the file types that MUST be included when the CPE notifies the ACS of AUTONOMOUS TRANSFER COMPLETE events. File types omitted from this list MUST NOT be included when the CPE notifies the ACS.

Each list item matches one of:

  • 1 Firmware Upgrade Image (Download Only)
  • 2 Web Content (Download Only)
  • 3 Vendor Configuration File (Download or Upload)
  • 4 Vendor Log File (Upload Only)
  • X [0-9A-F]{6} .* (For Vendor-Specific File Types, could be for either Download or Upload) Additionally, the following format is defined to allow the unique definition of vendor-specific file types:
  • “X is replaced by a 6 hexadecimal-digit OUI (organizationally unique identifier) as defined in [OUI], with all upper-case letters and any leading zeros included. The OUI used for a given vendor-specific file type MUST be one that is assigned to the organization that defined this file type (which is not necessarily the same as the vendor of the CPE or ACS). Note that an empty string indicates that all file types are excluded from this filter, effectively disabling CPE notification of AUTONOMOUS TRANSFER COMPLETE events to the ACS.
- 1.0
InternetGatewayDevice.Time. object R This object contains parameters relating an NTP or SNTP time client in the CPE. - 1.0
Enable boolean W Enables or disables the NTP or SNTP time client. - 1.0
NTPServer1 string(:64) W First NTP timeserver. Either a host name or IP address. - 1.0
NTPServer2 string(:64) W Second NTP timeserver. Either a host name or IP address. - 1.0
NTPServer3 string(:64) W Third NTP timeserver. Either a host name or IP address. - 1.0
NTPServer4 string(:64) W Fourth NTP timeserver. Either a host name or IP address. - 1.0
NTPServer5 string(:64) W Fifth NTP timeserver. Either a host name or IP address. - 1.0
CurrentLocalTime dateTime R

The current date and time in the CPE’s local time zone.

Active Notification requests for this parameter MAY be denied.

- 1.0
LocalTimeZone string(:6) W

The local time zone offset from UTC, ignoring daylight savings time adjustments, in the form:

+hh:mm
-hh:mm For example, this will always be “-08:00” for California, “+00:00” or “-00:00” for the United Kingdom, and “+01:00” for France. This parameter is OBSOLETED because the information that it represents is fully covered by LocalTimeZoneName.
- 1.0
LocalTimeZoneName string(:64) W

Name of the local time zone (human readable string).

The name SHOULD be encoded according to IEEE 1003.1 (POSIX). The following is an example value: EST+5EDT,M4.1.0/2,M10.5.0/2

- 1.0
DaylightSavingsUsed boolean W

Whether or not daylight savings time is in use in the CPE’s local time zone.

This parameter is OBSOLETED because the information that it represents is fully covered by LocalTimeZoneName.

- 1.0
DaylightSavingsStart dateTime W Current local date and time at which the switch to daylight savings time occurs. If daylight savings time is not used, this value is ignored. This parameter is OBSOLETED because the information that it represents is fully covered by LocalTimeZoneName. - 1.0
DaylightSavingsEnd dateTime W Current local date and time at which the switch from daylight savings time will occur. If daylight savings time is not used, this value is ignored. This parameter is OBSOLETED because the information that it represents is fully covered by LocalTimeZoneName. - 1.0
Status string R

Status of Time support on the CPE. Enumeration of:

  • Disabled
  • Unsynchronized
  • Synchronized
  • Error_FailedToSynchronize
  • Error (OPTIONAL) The Unsynchronized value indicates that the CPE’s absolute time has not yet been set. The Synchronized value indicates that the CPE has acquired accurate absolute time; its current time is accurate. The Error_FailedToSynchronize value indicates that the CPE failed to acquire accurate absolute time; its current time is not accurate. The Error value MAY be used by the CPE to indicate a locally defined error condition.
- 1.0
InternetGatewayDevice.UserInterface. object R This object contains parameters relating to the user interface of the CPE. - 1.0
UserDatabaseSupported boolean R Present only if the CPE provides a password-protected LAN-side user interface. Indicates whether or not the CPE supports a user database that provides per-user passwords that can be used for accessing the local user interface. - 1.0
PasswordRequired boolean W Present only if the CPE provides a password-protected LAN-side user interface. Indicates whether or not the local user interface MUST require a password to be chosen by the user. If false, the choice of whether or not a password is used is left to the user. - 1.0
PasswordUserSelectable boolean W Present only if the CPE provides a password-protected LAN-side user interface and supports LAN-side Auto-Configuration. Indicates whether or not a password to protect the local user interface of the CPE MAY be selected by the user directly, or MUST be equal to the password used by the LAN-side Auto-Configuration protocol. - 1.0
UpgradeAvailable boolean W Indicates that a CPE upgrade is available, allowing the CPE to display this information to the user. - 1.0
WarrantyDate dateTime W Indicates the date and time in UTC that the warranty associated with the CPE is to expire. - 1.0
ISPName string(:64) W The name of the customer’s ISP. - 1.0
ISPHelpDesk string(:32) W The help desk phone number of the ISP. - 1.0
ISPHomePage string(:256) W The URL of the ISP’s home page. - 1.0
ISPHelpPage string(:256) W The URL of the ISP’s on-line support page. - 1.0
base64(0:4095) W Base64 encoded GIF or JPEG image. The binary image is constrained to 4095 bytes or less. - 1.0
ISPLogoSize unsignedInt(0:4095) W Un-encoded binary image size in bytes. If ISPLogoSize input value is 0 then the ISPLogo is cleared. ISPLogoSize can also be used as a check to verify correct transfer and conversion of Base64 string to image size. - 1.0
ISPMailServer string(:256) W The URL of the ISP’s mail server. - 1.0
ISPNewsServer string(:256) W The URL of the ISP’s news server. - 1.0
TextColor string(:6) W The color of text on the GUI screens in RGB hexidecimal notation (e.g., FF0088). - 1.0
BackgroundColor string(:6) W The color of the GUI screen backgrounds in RGB hexidecimal notation (e.g., FF0088). - 1.0
ButtonColor string(:6) W The color of buttons on the GUI screens in RGB hexidecimal notation (e.g., FF0088). - 1.0
ButtonTextColor string(:6) W The color of text on buttons on the GUI screens in RGB hexidecimal notation (e.g., FF0088). - 1.0
AutoUpdateServer string(:256) W The server the CPE can check to see if an update is available for direct download to it. This MUST NOT be used by the CPE if the InternetGatewayDevice.ManagementServer.UpgradesManaged parameter is true. - 1.0
UserUpdateServer string(:256) W The server where a user can check via a web browser if an update is available for download to a PC. This MUST NOT be used by the CPE if the InternetGatewayDevice.ManagementServer.UpgradesManaged parameter is true. - 1.0
ExampleLogin string(:40) W An example of a correct login, according to ISP-specific rules. - 1.0
ExamplePassword string(:30) W An example of a correct password, according to ISP-specific rules. - 1.0
AvailableLanguages string[](:256) R Comma-separated list (maximum number of characters 256) of strings. Available user-interface languages, where each language is specified according to RFC 3066 [RFC3066]. - 1.0
SharedPassword boolean W Present only if the CPE provides a password-protected LAN-side user interface. Indicates whether or not a single shared password MUST protect the local user interface, or whether per-user passwords can be used. If either UserDatabaseSupported or PasswordUserSelectable is false, the CPE MUST ignore the value of this parameter. - 1.0
CurrentLanguage string(:16) W Current user-interface language, specified according to RFC 3066 [RFC3066]. - 1.0
InternetGatewayDevice.UserInterface.RemoteAccess. object R This object contains parameters relating to remotely accessing the CPE’s user interface. Remote access is defined as any entity not of a local subnet attempting to connect to the CPE. Remote access requires user authentication. To provide remote access authentication the CPE MUST support a User.{i}. with at least one instance that has User.{i}.RemoteAccessCapable set to true. - 1.0
Enable boolean W Enables/Disables remotely accessing the CPE’s user interface. - 1.0
Port unsignedInt(:65535) W Destination TCP port required for remote access connection. - 1.0
SupportedProtocols string[] R

Comma-separated list of strings. Indicates the protocols that are supported by the CPE for the purpose of remotely accessing the user interface.

Each list item is an enumeration of:

- 1.0
Protocol string W The value MUST be a member of the list reported by the SupportedProtocols parameter. This is the protocol currently being used for remote access. - 1.0
InternetGatewayDevice.UserInterface.LocalDisplay. object R This object describes how to remotely manage the initial positioning of a user interface on a device’s local display. - 1.0
Movable boolean W Controls whether the user is allowed to change the GUI window position on the local CPE’s display. - 1.0
Resizable boolean W Controls whether the user is allowed to resize the GUI window on the local CPE’s display. - 1.0
PosX int W

The horizontal position of the User Interface’s top left corner within the local CPE’s display measured from the top left corner, expressed in pixels.

Active Notification requests for this parameter MAY be denied.

- 1.0
PosY int W

The vertical position of the User Interface’s top left corner within the local CPE’s display measured from the top left corner, expressed in pixels.

Active Notification requests for this parameter MAY be denied.

- 1.0
Width unsignedInt W

The width of the user interface within the local CPE’s display, expressed in pixels.

Active Notification requests for this parameter MAY be denied.

- 1.0
Height unsignedInt W

The height of the user interface within the local CPE’s display, expressed in pixels.

Active Notification requests for this parameter MAY be denied.

- 1.0
DisplayWidth unsignedInt R The width of the local CPE’s display, expressed in pixels. - 1.0
DisplayHeight unsignedInt R The height of the local CPE’s display, expressed in pixels. - 1.0
InternetGatewayDevice.Layer3Forwarding. object R This object allows the handling of the routing and forwarding configuration of the device. - 1.0
DefaultConnectionService string(:256) W Specifies the default WAN interface. The content is the full hierarchical parameter name of the default layer 3 connection object. Example: InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANPPPConnection.1. - 1.0
ForwardNumberOfEntries unsignedInt R Number of forwarding instances. - 1.0
InternetGatewayDevice.Layer3Forwarding.Forwarding.{i}. object(0:) W

Layer 3 forwarding table. In addition to statically configured routes, this table MUST include dynamic routes learned through layer 3 routing protocols, including RIP, OSPF, DHCP, and IPCP. The CPE MAY reject attempts to delete or modify a dynamic route entry. For each incoming packet, the layer 3 forwarding decision is conceptually made as follows:

  • Only table entries with a matching ForwardingPolicy are considered, i.e. those that either do not specify a ForwardingPolicy, or else specify a ForwardingPolicy that matches that of the incoming packet.
  • For the remaining table entries, those for which the source address/mask matches are sorted by longest prefix, i.e. with the most specific networks first (an unspecified source address is a wild-card and always matches, with a prefix length of zero).
  • For the remaining table entries, those for which the destination address/mask matches are sorted by longest prefix, i.e. with the most specific networks first (an unspecified destination address is a wild-card and always matches, with a prefix length of zero).
  • The first of the remaining table entries is applied to the packet.

At most one enabled entry in this table can exist with the same values for all of DestIPAddress, DestSubnetMask, SourceIPAddress and SourceSubnetMask.

- 1.0
Enable boolean W Enables or disables the forwarding entry. On creation, an entry is disabled by default. false 1.0
Status string R

Indicates the status of the forwarding entry.

Enumeration of:

  • Disabled
  • Enabled
  • Error (OPTIONAL) The Error value MAY be used by the CPE to indicate a locally defined error condition.
Disabled 1.0
StaticRoute boolean R If true, this route is a Static route. true 1.0
Type string W

Indicates the type of route.

Enumeration of:

Host 1.0
DestIPAddress string(:45) W

[IPAddress] Destination address. An empty string or a value of “0.0.0.0” indicates no destination address is specified.

A Forwarding table entry for which DestIPAddress and DestSubnetMask are both an empty string or “0.0.0.0” is a default route.

<Empty> 1.0
DestSubnetMask string(:45) W

[IPAddress] Destination subnet mask. An empty string or a value of “0.0.0.0” indicates no destination subnet mask is specified.

If a destination subnet mask is specified, the DestSubnetMask is ANDed with the destination address before comparing with the DestIPAddress. Otherwise, the full destination address is used as is. A Forwarding table entry for which DestIPAddress and DestSubnetMask are both an empty string or “0.0.0.0” is a default route.

<Empty> 1.0
SourceIPAddress string(:45) W [IPAddress] Source address. An empty string or a value of “0.0.0.0” indicates no source address is specified. <Empty> 1.0
SourceSubnetMask string(:45) W

[IPAddress] Source subnet mask. An empty string or a value of “0.0.0.0” indicates no source subnet mask is specified.

If a source subnet mask is specified, the SourceSubnetMask is ANDed with the source address before comparing with the SourceIPAddress. Otherwise, the full source address is used as is.

<Empty> 1.0
GatewayIPAddress string(:45) W [IPAddress] IP address of the gateway. Only one of GatewayIPAddress and Interface SHOULD be configured for a route. If both are configured, GatewayIPAddress and Interface MUST be consistent with each other. <Empty> 1.0
Interface string(:256) W Specifies the egress interface associated with this entry. The value MUST be the Path Name of the layer 3 connection object. Example: InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANPPPConnection.1. Only one of GatewayIPAddress and Interface SHOULD be configured for a route. If both are configured, GatewayIPAddress and Interface MUST be consistent with each other. For a route that was configured by setting GatewayIPAddress but not Interface, read access to Interface MUST return the full hierarchical parameter name for the route’s egress interface. - 1.0
ForwardingMetric int(-1:) W Forwarding metric. A value of -1 indicates this metric is not used. -1 1.0
MTU unsignedInt(1:1540) W The maximum allowed size of an Ethernet frame for this route. - 1.0
ForwardingPolicy int(-1:) W Identifier of a set of classes or flows that have the corresponding ForwardingPolicy value as defined in the QueueManagement object. A value of -1 indicates no ForwardingPolicy is specified. If specified, this forwarding entry is to apply only to traffic associated with the specified classes and flows. -1 1.0
InternetGatewayDevice.LANConfigSecurity. object R This object contains generic device configuration information. - 1.0
ConfigPassword string(:64) W

A password to allow LAN access to protected auto-configuration services. If the CPE supports TR-064 (LAN-side DSL CPE Configuration Protocol), this parameter is to be used as the dslf-config password (as defined in TR-064). If the CPE has a user interface with password protection enabled, this parameter is also to be used as the user password for password-protected operations. However, this parameter MUST NOT be used to set the user password if the parameter InternetGatewayDevice.UserInterface.PasswordUserSelectable is true.

When read, this parameter returns an empty string, regardless of the actual value.

- 1.0
InternetGatewayDevice.IPPingDiagnostics. object R This object provides access to an IP-layer ping test. - 1.0
DiagnosticsState string W

Indicates availability of diagnostic data. Enumeration of:

  • None (READONLY)
  • Requested
  • Complete (READONLY)
  • Error_CannotResolveHostName (READONLY)
  • Error_Internal (READONLY)
  • Error_Other (READONLY) If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Complete (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Complete, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code 8 DIAGNOSTICS COMPLETE in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None. Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None. While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None. While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

Active Notification requests for this parameter MAY be denied.

- 1.0
Interface string(:256) W The value MUST be the Path Name of the WAN or LAN IP-layer interface over which the test is to be performed. This identifies the source IP address to use when performing the test. The following is a WAN interface example: InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANPPPConnection.1 The following is a LAN interface example: InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface.1 The value of this parameter MUST be either a valid interface or an empty string. An attempt to set this parameter to a different value MUST be rejected as an invalid parameter value. If an empty string is specified, the CPE MUST use the interface as directed by its routing policy (Forwarding table entries) to determine the appropriate interface. - 1.0
Host string(:256) W Host name or address of the host to ping. - 1.0
NumberOfRepetitions unsignedInt(1:) W Number of repetitions of the ping test to perform before reporting the results. - 1.0
Timeout unsignedInt(1:) W Timeout in milliseconds for the ping test. - 1.0
DataBlockSize unsignedInt(1:65535) W Size of the data block in bytes to be sent for each ping. - 1.0
DSCP unsignedInt(0:63) W DiffServ codepoint to be used for the test packets. By default the CPE SHOULD set this value to zero. - 1.0
SuccessCount unsignedInt R

Result parameter indicating the number of successful pings (those in which a successful response was received prior to the timeout) in the most recent ping test.

Active Notification requests for this parameter MAY be denied.

- 1.0
FailureCount unsignedInt R

Result parameter indicating the number of failed pings in the most recent ping test.

Active Notification requests for this parameter MAY be denied.

- 1.0
AverageResponseTime unsignedInt R

Result parameter indicating the average response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero.

Active Notification requests for this parameter MAY be denied.

- 1.0
MinimumResponseTmie unsignedInt R Result parameter indicating the minimum response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero. - 1.0
MaximumResponseTime unsignedInt R

Result parameter indicating the maximum response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero.

Active Notification requests for this parameter MAY be denied.

- 1.0
MinimumResponseTime unsignedInt R

Result parameter indicating the minimum response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.LANDevice.{i}. object(0:) W Each instance models a LAN side layer 3 IP interface. Each instance has children that correspond to the layer 2 interfaces that are connected to the Gateway’s IP router via the modeled IP interface. If a LANDevice instance is deleted, the objects modeling those layer 2 interfaces that are as a result no longer connected to the Gateway’s IP router will move to the InternetGatewayDevice.LANInterfaces object. If the Layer2Bridging object is implemented, the view that it provides of the CPE’s underlying bridging configuration MUST be consistent with the view provided by any LANDevice and WAN**Connection objects. The implications of this are explained in [Annex A.6/TR-098a2]. - 1.0
LANEthernetInterfaceNumberOfEntries unsignedInt R Number of instances of LANEthernetInterfaceConfig in this LANDevice. 0 1.0
LANUSBInterfaceNumberOfEntries unsignedInt R Number of instances of LANUSBInterfaceConfig in this LANDevice. 0 1.0
LANWLANConfigurationNumberOfEntries unsignedInt R Number of instances of WLANConfiguration in this LANDevice. 0 1.0
InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement. object R

This object enables reporting of LAN-related device information and setting and configuring LAN IP addressing.

The DHCP parameters in this object define the behavior of the default DHCP server, i.e. the behavior for DHCP requests that do not match any of the DHCP conditional serving pool entries.

- 1.0
MACAddress string(:17) R [MACAddress] The MAC address associated with the IP interface modeled by this LANDevice instance. This is the MAC address that is returned in response to an ARP request for any of the IP interface’s IP addresses. It is also the source MAC address in all IP traffic sent over the IP interface. If no single MAC address meets the above criteria, the value of this parameter MUST be the all-zero MAC address 00:00:00:00:00:00. - 1.0
DHCPServerConfigurable boolean W Enables the configuration of the DHCP server on the LAN interface. If this variable is set to false, the CPE SHOULD restore its default DHCP server settings. true 1.0
DHCPServerEnable boolean W Enables or disables the DHCP server on the LAN interface. false 1.0
DHCPRelay boolean R Indicates if the DHCP server performs the role of a server (false) or a relay (true) on the LAN interface. This parameter is DEPRECATED because the functionality that it describes is not well-defined. The CPE MAY set it to the value that it thinks most appropriate, based on its configuration. - 1.0
MinAddress string(:45) W

[IPAddress] Specifies first address in the pool to be assigned by the DHCP server on the LAN interface.

This parameter MUST have a valid value before the DHCP server can be enabled.

- 1.0
MaxAddress string(:45) W

[IPAddress] Specifies last address in the pool to be assigned by the DHCP server on the LAN interface.

This parameter MUST have a valid value before the DHCP server can be enabled.

- 1.0
ReservedAddresses string(:45)[](:256) W [IPAddress] Comma-separated list (maximum number of characters 256) of IP Addresses. Addresses marked reserved from the address allocation pool. <Empty> 1.0
SubnetMask string(:45) W

[IPAddress] Specifies the client’s network subnet mask.

This parameter MUST have a valid value before the DHCP server can be enabled.

- 1.0
DNSServers string(:45)[](:64) W [IPAddress] Comma-separated list (maximum number of characters 64) of IP Addresses. DNS servers offered to DHCP clients. Support for more than three DNS Servers is OPTIONAL. - 1.0
DomainName string(:64) W Sets the domain name to provide to clients on the LAN interface. - 1.0
IPRouters string(:45)[](:64) W [IPAddress] Comma-separated list (maximum number of characters 64) of IP Addresses. IP addresses of routers on this subnet. Also known as default gateway. Support for more than one Router address is OPTIONAL. - 1.0
DHCPLeaseTime int(-1:) W Specifies the lease time in seconds of client assigned addresses. A value of -1 indicates an infinite lease. 86400 1.0
UseAllocatedWAN string W

Controls use of addresses from the associated WAN connection. Enumeration of:

  • Normal
  • UseAllocatedSubnet (DEPRECATED)
  • Passthrough If Normal, the address pool is directly configured by the ACS. If {{enum: reference to deprecated enumeration InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.UseAllocatedWAN.UseAllocatedSubnet}}, behavior is the same as for Passthrough with an empty PassthroughMACAddress. For this reason, {{enum: reference to deprecated enumeration InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.UseAllocatedWAN.UseAllocatedSubnet}} is DEPRECATED. If Passthrough, and PassthroughMACAddress is an empty string, the configured values of the MinAddress, MaxAddress, SubnetMask and DNSServers parameters are ignored. The corresponding address pool values are instead taken from the WAN connection specified by AssociatedConnection. If Passthrough, and PassthroughMACAddress is not an empty string, the LAN Host identified by PassthroughMACAddress is given a WAN IP address from the WAN connection specified by AssociatedConnection. Other LAN Hosts are treated as for Normal. Use of PassthroughMACAddress does not cover the case where more than one LAN Host is to be given a WAN IP address. This can be achieved by using a DHCP conditional serving pool.
Normal 1.0
AssociatedConnection string(:256) W The value MUST be the Path Name of the connection instance to be used for address allocation if UseAllocatedWAN is set to {{enum: reference to deprecated enumeration InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.UseAllocatedWAN.UseAllocatedSubnet}} or Passthrough. The content is the full hierarchical parameter name of a WAN-side layer 3 connection object. Example: InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANPPPConnection.1. If UseAllocatedWAN is {{enum: reference to deprecated enumeration InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.UseAllocatedWAN.UseAllocatedSubnet}} or Passthrough, this parameter MUST have a valid value before the DHCP server can be enabled. - 1.0
PassthroughLease unsignedInt W DHCP lease time in seconds given to the LAN Host that is used to passthrough a WAN IP address if UseAllocatedWAN is Passthrough. Note: A temporary private IP address with short lease (for example, 1 min) might be given to the passthrough LAN Host before the WAN IP address is acquired. 600 1.0
PassthroughMACAddress string(:17) W [MACAddress] Hardware address of the LAN Host that is used to passthrough a WAN IP address if UseAllocatedWAN is Passthrough. Note: an empty string indicates that no specific LAN Host is designated, and results in the same behavior as the (DEPRECATED) {{enum: reference to deprecated enumeration InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.UseAllocatedWAN.UseAllocatedSubnet}}. - 1.0
AllowedMACAddresses string(:17)[](:512) W [MACAddress] Comma-separated list (maximum number of characters 512) of MAC Addresses. Hardware addresses that are allowed to connect to this connection if MACAddressControlEnabled is 1 for a given interface. - 1.0
IPInterfaceNumberOfEntries unsignedInt R The number of entries in the IPInterface table. 0 1.0
DHCPStaticAddressNumberOfEntries unsignedInt R The number of entries in the DHCPStaticAddress table. 0 1.0
DHCPOptionNumberOfEntries unsignedInt R The number of entries in the DHCPOption table. 0 1.0
DHCPConditionalPoolNumberOfEntries unsignedInt R The number of entries in the DHCPConditionalServingPool table. 0 1.0
InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.IPInterface.{i}. object(0:) W

IP address table with each object representing an IP address on the LANDevice IP interface. Support for more than one interface instance is OPTIONAL.

At most one enabled entry in this table can exist with the same values for both IPInterfaceIPAddress and IPInterfaceSubnetMask.

- 1.0
Enable boolean W Enables or disables this entry. On creation, an entry is disabled by default. false 1.0
IPInterfaceIPAddress string(:45) W [IPAddress] IP address of the LAN-side interface of the CPE. <Empty> 1.0
IPInterfaceSubnetMask string(:45) W [IPAddress] Subnet mask of the LAN-side interface of the IGD. <Empty> 1.0
IPInterfaceAddressingType string W

Represents the addressing method used to assign the LAN-side IP address of the CPE on this interface.

Enumeration of:

  • DHCP
  • Static
  • AutoIP
DHCP 1.0
InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.DHCPStaticAddress.{i}. object(0:) W

DHCP static address table. Entries in this table correspond to what RFC 2131 [RFC2131] calls “manual allocation”, where a client’s IP address is assigned by the network administrator, and DHCP is used simply to convey the assigned address to the client. Each instance of this object specifies a hardware address (MAC address) and an IP address within the pool. When serving from this pool, this IP address MUST, if available, be assigned to the DHCP client with this hardware address, and MUST NOT be assigned to any other client. Note that it is possible that an IP address in this table is present in one or more of the conditional serving pools, in which case it is possible that such an address will be assigned to a different client.

At most one enabled entry in this table can exist with a given value for Chaddr.

- 1.0
Enable boolean W Enables or disables the DHCPStaticAddress table entry. Disabling an entry does not return the IP address to the pool. false 1.0
Chaddr string(:17) W [MACAddress] Hardware address (MAC address) of the physical interface of the DHCP client. This parameter MUST have a valid value before the table entry can be enabled. <Empty> 1.0
Yiaddr string(:45) W [IPAddress] IP address to be assigned by the DHCP server to the DHCP client with the specified hardware address (MAC address). This parameter MUST have a valid value before the table entry can be enabled. <Empty> 1.0
InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.DHCPOption.{i}. object(0:) W

This object specifies the DHCP options that MUST, if enabled, be returned to clients whose DHCP requests do not match any of the DHCP conditional serving pool entries.

At most one enabled entry in this table can exist with a given value for Tag.

- 1.0
Enable boolean W Enables or disables this DHCPOption table entry. false 1.0
Tag unsignedInt(1:254) W Option tag as defined in RFC 2132 [RFC2132]. - 1.0
Value base64(0:255) W Base64 encoded option value. <Empty> 1.0
InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.DHCPConditionalServingPool.{i}. object(0:) W DHCP conditional serving pool table. Each instance of this object defines a DHCP conditional serving pool. Client requests are associated with pools based on criteria such as source interface, supplied DHCP options, and MAC address. If a DHCP request does not match any of the DHCP conditional serving pool entries, the handling of the request is determined by the default DHCP server behavior that is defined by the LANHostConfigManagement object. Overlapping pool ranges MUST be supported. - 1.0
Enable boolean W Enables or disables the DHCPConditionalServingPool entry. false 1.0
PoolOrder unsignedInt(1:) W Position of the pool entry in the order of precedence. A value of 1 indicates the first entry considered. For each DHCP request, the highest ordered entry that matches the association criteria is applied. All lower order entries are ignored. When this value is modified, if the value matches that of an existing entry, the Order value for the existing entry and all lower Order entries is incremented (lowered in precedence) to ensure uniqueness of this value. A deletion causes Order values to be compacted. When a value is changed, incrementing occurs before compaction. The value on creation of a DHCPConditionalServingPool table entry MUST be one greater than the largest current value. - 1.0
SourceInterface string[](:1024) W Pool association criterion. Comma-separated list (maximum number of characters 1024) of strings. Each list item MUST be the Path Name of the layer 2 ingress interfaces associated with this entry, i.e. the corresponding LAN**InterfaceConfig or WLANConfiguration objects. For example: InternetGatewayDevice.LANDevice.1.LANEthernetInterfaceConfig.2,InternetGatewayDevice.LANDevice.1.WLANConfiguration.3 an empty string indicates this entry is to apply to all layer 2 interface objects under this LANDevice instance. <Empty> 1.0
VendorClassID string(:256) W Pool association criterion. Used to identify one or more LAN devices, value of the DHCP Vendor Class Identifier (Option 60) as defined in RFC 2132 [RFC2132], matched according to the criterion in VendorClassIDMode. Case sensitive. An empty string indicates this criterion is not used for conditional serving. <Empty> 1.0
VendorClassIDExclude boolean W If false, matching packets are those that match the VendorClassID entry, if specified. If true, matching packets are those that do not match the VendorClassID entry, if specified. false 1.0
VendorClassIDMode string W

VendorClassID pattern match criterion. Enumeration of:

  • Exact
  • Prefix
  • Suffix
  • Substring For example, if VendorClassID is “Example” then an Option 60 value of “Example device” will match with VendorClassIDMode values of Prefix or Substring, but not with Exact or Suffix.
Exact 1.0
ClientID string(:256) W Pool association criterion. Used to identify one or more LAN devices, value of the DHCP Client Identifier (Option 61) as defined in RFC 2132 [RFC2132]. The option value is binary, so an exact match is REQUIRED. An empty string indicates this criterion is not used for conditional serving. <Empty> 1.0
ClientIDExclude boolean W If false, matching packets are those that match the ClientID entry, if specified. If true, matching packets are those that do not match the ClientID entry, if specified. false 1.0
UserClassID string(:256) W Pool association criterion. Used to identify one or more LAN devices, value of the DHCP User Class Identifier (Option 77) as defined in RFC 3004 [RFC3004]. An empty string indicates this criterion is not used for conditional serving. <Empty> 1.0
UserClassIDExclude boolean W If false, matching packets are those that match the UserClassID entry, if specified. If true, matching packets are those that do not match the UserClassID entry, if specified. false 1.0
Chaddr string(:17) W [MACAddress] Pool association criterion. Hardware address (MAC address.) of the physical interface of the DHCP client. An empty string indicates this criterion is not used for conditional serving. <Empty> 1.0
ChaddrMask string(:17) W [MACAddress] Bit-mask for the MAC address, where matching of a packet’s MAC address with the Chaddr is only to be done for bit positions set to one in the mask. A mask of FF:FF:FF:FF:FF:FF or an empty string indicates all bits of the Chaddr are to be used for conditional serving classification. <Empty> 1.0
ChaddrExclude boolean W If false, matching packets are those that match the (masked) Chaddr entry, if specified. If true, matching packets are those that do not match the (masked) Chaddr entry, if specified. false 1.0
LocallyServed boolean W If true, then the local DHCP server will assign an IP address from the specific address pool specified in this object. If false, the DHCP server will send the request to the DHCPServerIPAddress configured for this pool. true 1.0
MinAddress string(:45) W [IPAddress] Specifies first address in the pool to be assigned by the DHCP server on the LAN interface. This parameter is configurable only if UseAllocatedWAN is Normal. This parameter MUST have a valid value before this pool can be enabled. - 1.0
MaxAddress string(:45) W [IPAddress] Specifies last address in the pool to be assigned by the DHCP server on the LAN interface. This parameter is configurable only if UseAllocatedWAN is Normal. This parameter MUST have a valid value before this pool can be enabled. - 1.0
ReservedAddresses string(:45)[](:512) W [IPAddress] Comma-separated list (maximum number of characters 512) of IP Addresses. IP addresses marked reserved from the address allocation pool. <Empty> 1.0
SubnetMask string(:45) W [IPAddress] Specifies the client’s network subnet mask. This parameter is configurable only if UseAllocatedWAN is Normal. This parameter MUST have a valid value before this pool can be enabled. - 1.0
DNSServers string(:45)[](:64) W [IPAddress] Comma-separated list (maximum number of characters 64) of IP Addresses. DNS servers offered to DHCP clients. Support for more than three DNS Servers is OPTIONAL. This parameter is configurable only if UseAllocatedWAN is Normal. - 1.0
DomainName string(:64) W Sets the domain name to provide to clients on the LAN interface. - 1.0
IPRouters string(:45)[](:64) W [IPAddress] Comma-separated list (maximum number of characters 64) of IP Addresses. IP addresses of routers on this subnet. Also known as default gateway. Support for more than one Router address is OPTIONAL. - 1.0
DHCPLeaseTime int(-1:) W Specifies the lease time in seconds of client assigned addresses. A value of -1 indicates an infinite lease. 86400 1.0
UseAllocatedWAN string W

Controls whether the MinAddress, MaxAddress, SubnetMask and DNSServers parameters are configurable or are taken from the associated WAN connection. Enumeration of:

  • Normal
  • Passthrough If Normal, the above-mentioned pool parameters are directly configured by the ACS. If Passthrough, the above-mentioned pool parameters cannot be configured by the ACS. Their values are instead taken from the WAN connection specified by AssociatedConnection.
Normal 1.0
AssociatedConnection string(:256) W The value MUST be the Path Name of the connection instance to be used for address allocation if UseAllocatedWAN is set to Passthrough. The content is the full hierarchical parameter name of a WAN-side layer 3 connection object. Example: InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANPPPConnection.1. If UseAllocatedWAN is Passthrough, this parameter MUST have a valid value before this pool can be enabled. - 1.0
DHCPServerIPAddress string(:45) W [IPAddress] IP address of the DHCP server, where the request has to be sent to when there is a conditional match with this pool and LocallyServed is false. If this parameter is not configured, then the DHCP request is dropped. - 1.0
DHCPStaticAddressNumberOfEntries unsignedInt R The number of entries in the DHCPStaticAddress table. 0 1.0
DHCPOptionNumberOfEntries unsignedInt R The number of entries in the DHCPOption table. 0 1.0
InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.DHCPConditionalServingPool.{i}.DHCPStaticAddress.{i}. object(0:) W

DHCP static address table. Entries in this table correspond to what RFC 2131 [RFC2131] calls “manual allocation”, where a client’s IP address is assigned by the network administrator, and DHCP is used simply to convey the assigned address to the client. Each instance of this object specifies a hardware address (MAC address) and an IP address within the pool. When serving from this pool, this IP address MUST, if available, be assigned to the DHCP client with this hardware address, and MUST NOT be assigned to any other client. Note that it is possible that an IP address in this table is present in the main pool and/or one or more of the other conditional serving pools, in which case it is possible that such an address will be assigned to a different client.

At most one enabled entry in this table can exist with a given value for Chaddr.

- 1.0
Enable boolean W Enables or disables the DHCPStaticAddress table entry. Disabling an entry does not return the IP address to the pool. false 1.0
Chaddr string(:17) W [MACAddress] Hardware address (MAC address) of the physical interface of the DHCP client. This parameter MUST have a valid value before the table entry can be enabled. <Empty> 1.0
Yiaddr string(:45) W [IPAddress] IP address to be assigned by the DHCP server to the DHCP client with the specified hardware address (MAC address). This parameter MUST have a valid value before the table entry can be enabled. <Empty> 1.0
InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.DHCPConditionalServingPool.{i}.DHCPOption.{i}. object(0:) W

This object specifies the DHCP options that MUST, if enabled, be returned to clients whose DHCP requests are associated with this pool.

At most one enabled entry in this table can exist with a given value for Tag.

- 1.0
Enable boolean W Enables or disables this DHCPOption table entry. false 1.0
Tag unsignedInt(1:254) W Option tag as defined in RFC 2132 [RFC2132]. - 1.0
Value base64(0:255) W Base64 encoded option value. <Empty> 1.0
InternetGatewayDevice.LANDevice.{i}.LANEthernetInterfaceConfig.{i}. object(0:) R

This object models an Ethernet LAN connection on a CPE device. This object MUST be implemented for CPE that contain an Ethernet interface on the LAN side.

At most one entry in this table can exist with a given value for MACAddress.

- 1.0
Enable boolean W Enables or disables this interface. - 1.0
Status string R

Indicates the status of this interface.

Enumeration of:

  • Up
  • NoLink
  • Error (OPTIONAL)
  • Disabled The Error value MAY be used by the CPE to indicate a locally defined error condition.
- 1.0
Name string(:16) R The name of this layer 2 interface, chosen by the vendor, e.g. “eth0” or “eth0:1”. - 1.0
MACAddress string(:17) R [MACAddress] The physical address of the interface. - 1.0
MACAddressControlEnabled boolean W Indicates whether MAC Address Control is enabled or not on this interface. MAC Address Control limits the clients that connect to those that match a list of allowed MAC addresses specified in InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.AllowedMACAddresses. - 1.0
MaxBitRate string W

The maximum upstream and downstream bit rate available to this connection.

Enumeration of:

  • 10
  • 100
  • 1000
  • 10000
  • Auto
- 1.0
DuplexMode string W

The duplex mode available to this connection.

Enumeration of:

  • Half
  • Full
  • Auto
- 1.0
InternetGatewayDevice.LANDevice.{i}.LANEthernetInterfaceConfig.{i}.Stats. object R

This object contains statistics for an Ethernet LAN interface on a CPE device.

Note that these statistics refer to the link layer, not to the physical layer.

- 1.0
BytesSent unsignedInt R

The total number of bytes transmitted out of the interface, including framing characters. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
BytesReceived unsignedInt R

The total number of bytes received on the interface, including framing characters. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
PacketsSent unsignedInt R

The total number of packets transmitted out of the interface. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
PacketsReceived unsignedInt R

The total number of packets which were received on this interface. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
ErrorsSent unsignedInt R

The total number of outbound packets that could not be transmitted because of errors. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
ErrorsReceived unsignedInt R

The total number of inbound packets that contained errors preventing them from being deliverable. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
UnicastPacketsSent unsignedInt R

The total number of packets requested for transmission which were not addressed to a multicast or broadcast address, including those that were discarded or not sent. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
UnicastPacketsReceived unsignedInt R

The total number of received packets which were not addressed to a multicast or broadcast address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
DiscardPacketsSent unsignedInt R

The total number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
DiscardPacketsReceived unsignedInt R

The total number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable. One possible reason for discarding such a packet could be to free up buffer space. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
MulticastPacketsSent unsignedInt R

The total number of packets requested for transmission which were addressed to a multicast address, including those that were discarded or not sent. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
MulticastPacketsReceived unsignedInt R

The total number of received packets which were addressed to a multicast address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
BroadcastPacketsSent unsignedInt R

The total number of packets requested for transmission which were addressed to a broadcast address, including those that were discarded or not sent. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
BroadcastPacketsReceived unsignedInt R

The total number of received packets which were addressed to a broadcast address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
UnknownProtoPacketsReceived unsignedInt R

The total number of packets received via the interface which were discarded because of an unknown or unsupported protocol. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.LANDevice.{i}.LANUSBInterfaceConfig.{i}. object(0:) R

This object models a USB LAN connection on a CPE device. This object MUST be implemented for CPE that contain a USB interface on the LAN side.

At most one entry in this table can exist with a given value for MACAddress.

- 1.0
Enable boolean W Enables or disables this interface. - 1.0
Status string R

Indicates the status of this interface.

Enumeration of:

  • Up
  • NoLink
  • Error (OPTIONAL)
  • Disabled The Error value MAY be used by the CPE to indicate a locally defined error condition.
- 1.0
Name string(:16) R The name of this layer 2 interface, chosen by the vendor, e.g. “usb0”. - 1.0
MACAddress string(:17) R [MACAddress] The physical address of the interface. - 1.0
MACAddressControlEnabled boolean W Indicates whether MAC Address Control is enabled or not on this interface. MAC Address Control limits the clients that connect to those that match a list of allowed MAC addresses specified in InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.AllowedMACAddresses. - 1.0
Standard string(:6) R USB version supported by the device. - 1.0
Type string R

Type of the USB interface.

Enumeration of:

  • Host
  • Hub
  • Device
- 1.0
Rate string R

Speed of the USB interface.

Enumeration of:

  • Low
  • Full
  • High (USB 2.0)
- 1.0
Power string R

Power configuration of the USB interface.

Enumeration of:

  • Self
  • Bus
  • Unknown
- 1.0
InternetGatewayDevice.LANDevice.{i}.LANUSBInterfaceConfig.{i}.Stats. object R

This object contains statistics for a USB LAN interface on a CPE device.

Note that these statistics refer to the link layer, not to the physical layer.

- 1.0
BytesSent unsignedInt R

The total number of bytes transmitted out of the interface, including framing characters. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
BytesReceived unsignedInt R

The total number of bytes received on the interface, including framing characters. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
CellsSent unsignedInt R

The total number of packets (cells) transmitted out of the interface. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
CellsReceived unsignedInt R

The total number of packets (cells) which were received on this interface. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
ErrorsSent unsignedInt R

The total number of outbound packets that could not be transmitted because of errors. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
ErrorsReceived unsignedInt R

The total number of inbound packets that contained errors preventing them from being deliverable. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
UnicastPacketsSent unsignedInt R

The total number of packets requested for transmission which were not addressed to a multicast or broadcast address, including those that were discarded or not sent. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
UnicastPacketsReceived unsignedInt R

The total number of received packets which were not addressed to a multicast or broadcast address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
DiscardPacketsSent unsignedInt R

The total number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
DiscardPacketsReceived unsignedInt R

The total number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable. One possible reason for discarding such a packet could be to free up buffer space. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
MulticastPacketsSent unsignedInt R

The total number of packets requested for transmission which were addressed to a multicast address, including those that were discarded or not sent. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
MulticastPacketsReceived unsignedInt R

The total number of received packets which were addressed to a multicast address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
BroadcastPacketsSent unsignedInt R

The total number of packets requested for transmission which were addressed to a broadcast address, including those that were discarded or not sent. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
BroadcastPacketsReceived unsignedInt R

The total number of received packets which were addressed to a broadcast address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
UnknownProtoPacketsReceived unsignedInt R

The total number of packets received via the interface which were discarded because of an unknown or unsupported protocol. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}. object(0:) R

This object models an 802.11 LAN connection on a CPE device. This object MUST be implemented for CPE that contain an 802.11 interface on the LAN side.

At most one entry in this table can exist with a given value for BSSID, or with a given value for SSID.

- 1.0
Enable boolean W

Enables or disables this interface.

When there are multiple WLANConfiguration instances, e.g. each instance supports a different 802.11 standard or has a different security configuration, this parameter can be used to control which of the instances are currently enabled.

- 1.0
Status string R

Indicates the status of this interface.

Enumeration of:

  • Up
  • Error (OPTIONAL)
  • Disabled The Error value MAY be used by the CPE to indicate a locally defined error condition.
- 1.0
Name string(:16) R The name of this layer 2 interface, chosen by the vendor, e.g. “wlan0”. - 1.0
BSSID string R The MAC address of the interface. - 1.0
MaxBitRate string(:4) W The maximum upstream and downstream bit rate available to this connection in Mbps. Either Auto, or the largest of the OperationalDataTransmitRates values. - 1.0
Channel unsignedInt(0:255) W The current radio channel used by the connection. To request automatic channel selection, set AutoChannelEnable to true. Whenever AutoChannelEnable is true, the value of the Channel parameter MUST be the channel selected by the automatic channel selection procedure. - 1.0
SSID string(:32) W The current service set identifier in use by the connection. The SSID is an identifier that is attached to packets sent over the wireless LAN that functions as a “password” for joining a particular radio network (BSS). Note: If an access point wishes to be known by more than one SSID, it MUST provide a WLANConfiguration instance for each SSID. - 1.0
BeaconType string W

The capabilities that are currently enabled on the access point (and that are announced via beacons if BeaconAdvertisementEnabled is true). Write access to this parameter enables and disables such capabilities. An attempt to set this parameter to one of the REQUIRED (mandatory) values MAY be rejected if (and only if) the requested capability is not available on this WLANConfiguration instance but is available on another WLANConfiguration instance within this Internet Gateway Device. For example, only basic 802.11 might be supported by one virtual AP, and only WPA might be supported by another virtual AP. A value of None means that no capabilities are currently enabled on the access point and that no stations will be able to associate with it. Enumeration of:

  • None
  • Basic
  • WPA
  • 11i (OPTIONAL)
  • BasicandWPA (OPTIONAL, OBSOLETED)
  • Basicand11i (OPTIONAL, OBSOLETED)
  • WPAand11i (OPTIONAL)
  • BasicandWPAand11i (OPTIONAL, OBSOLETED) 11i SHOULD be taken to refer to both the 802.11i specification and to the WPA2 specification (any WPA2-certified device will implement all mandatory parts of the 802.11i standard). The OBSOLETED values are those for Basic + WPA/WPA2 mixed modes, which are not permitted by the WPA specifications.
- 1.0
MACAddressControlEnabled boolean W Indicates whether MAC Address Control is enabled or not on this interface. MAC Address Control limits the clients that connect to those that match a list of allowed MAC addresses specified in InternetGatewayDevice.LANDevice.{i}.LANHostConfigManagement.AllowedMACAddresses. - 1.0
Standard string R

Indicates which IEEE 802.11 standard this WLANConfiguration instance is configured for. Enumeration of:

  • a
  • b
  • g (b and g clients supported)
  • g-only (only g clients supported)
  • n Where each value indicates support for only the indicated standard. If the device is configured simultaneously for more than one standard, a separate WLANConfiguration instance MUST be used for each supported standard.
- 1.0
WEPKeyIndex unsignedInt(1:4) W The index of the default WEP key. - 1.0
KeyPassphrase string(:63) W

A passphrase from which the WEP keys are to be generated. This parameter is the same as the parameter InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.PreSharedKey.1.KeyPassphrase for the same instance of WLANConfiguration. When either parameter is changed, the value of the other is changed as well. If KeyPassphrase is written, all four WEP keys are immediately generated. The ACS SHOULD NOT set the passphrase and also set the WEP keys directly (the result of doing this is undefined). This MUST either be a valid key length divided by 8, in which case each byte contributes 8 bits to the key, or else MUST consist of Hex digits and be a valid key length divided by 4, in which case each byte contributes 4 bits to the key. Note: If a passphrase is used, all four WEP keys will be the same.

When read, this parameter returns an empty string, regardless of the actual value.

- 1.0
WEPEncryptionLevel string[](:64) R

Comma-separated list (maximum number of characters 64) of strings. Supported key lengths. Each list item is an enumeration of:

  • Disabled
  • 40-bit
  • 104-bit Any additional vendor-specific values MUST start with the key length in bits. This parameter does not enforce a given encryption level but only indicates capabilities. The WEP encryption level for a given key is inferred from the key length.
- 1.0
BasicEncryptionModes string(:31) W

Encryption modes that are available when basic 802.11 is enabled. WEPEncryption implies that all wireless clients can use WEP for data encryption.

Enumeration of:

  • None
  • WEPEncryption If this WLANConfiguration instance does not support basic 802.11 then this parameter MUST NOT be present in this instance of the WLANConfiguration object.
- 1.0
BasicAuthenticationMode string(:31) W

Authentication modes that are available when basic 802.11 is enabled.

Enumeration of:

  • None (Open authentication)
  • EAPAuthentication (OPTIONAL)
  • SharedAuthentication (OPTIONAL) If this WLANConfiguration instance does not support basic 802.11 then this parameter MUST NOT be present in this instance of the WLANConfiguration object.
- 1.0
WPAEncryptionModes string(:31) W

Encryption modes that are available when WPA is enabled.

Enumeration of:

  • WEPEncryption (DEPRECATED)
  • TKIPEncryption
  • WEPandTKIPEncryption (DEPRECATED)
  • AESEncryption (OPTIONAL)
  • WEPandAESEncryption (OPTIONAL, DEPRECATED)
  • TKIPandAESEncryption (OPTIONAL)
  • WEPandTKIPandAESEncryption (OPTIONAL, DEPRECATED) If this WLANConfiguration instance does not support WPA then this parameter MUST NOT be present in this instance of the WLANConfiguration object. The DEPRECATED values are those that combine WEP with TKIP and/or AES, which is not permitted by the WPA specifications.
- 1.0
WPAAuthenticationMode string(:31) W

Authentication modes that are available when WPA is enabled.

Enumeration of:

  • PSKAuthentication
  • EAPAuthentication (OPTIONAL) If this WLANConfiguration instance does not support WPA then this parameter MUST NOT be present in this instance of the WLANConfiguration object.
- 1.0
IEEE11iEncryptionModes string(:31) W

Encryption modes that are available when 802.11i is enabled.

Enumeration of:

  • WEPEncryption (DEPRECATED)
  • TKIPEncryption (OPTIONAL)
  • WEPandTKIPEncryption (DEPRECATED)
  • AESEncryption (OPTIONAL)
  • WEPandAESEncryption (OPTIONAL, DEPRECATED)
  • TKIPandAESEncryption (OPTIONAL)
  • WEPandTKIPandAESEncryption (OPTIONAL, DEPRECATED) If this WLANConfiguration instance does not support 802.11i then this parameter MUST NOT be present in this instance of the WLANConfiguration object. IEEE11i SHOULD be taken to refer to both the 802.11i specification and to the WPA2 specification (any WPA2-certified device will implement all mandatory parts of the 802.11i standard). The DEPRECATED values are those that combine WEP with TKIP and/or AES, which is not permitted by the WPA2 specifications.
- 1.0
IEEE11iAuthenticationMode string(:31) W

Authentication modes that are available when 802.11i is enabled.

Enumeration of:

  • PSKAuthentication
  • EAPAuthentication (OPTIONAL)
  • EAPandPSKAuthentication (OPTIONAL) If this WLANConfiguration instance does not support 802.11i then this parameter MUST NOT be present in this instance of the WLANConfiguration object. IEEE11i SHOULD be taken to refer to both the 802.11i specification and to the WPA2 specification (any WPA2-certified device will implement all mandatory parts of the 802.11i standard).
- 1.0
PossibleChannels string[](:1024) R Comma-separated list (maximum number of characters 1024) of strings. Possible radio channels for the wireless standard (a, b or g) and the regulatory domain. Ranges in the form “n-m” are permitted. For example, for 802.11b and North America, would be “1-11”. - 1.0
BasicDataTransmitRates string[](:256) W Comma-separated list (maximum number of characters 256) of strings. Maximum access point data transmit rates in Mbps for unicast, multicast and broadcast frames. For example, a value of “1,2”, indicates that unicast, multicast and broadcast frames can be transmitted at 1 Mbps and 2 Mbps. - 1.0
OperationalDataTransmitRates string[](:256) W Comma-separated list (maximum number of characters 256) of strings. Maximum access point data transmit rates in Mbps for unicast frames (a superset of BasicDataTransmitRates). Given the value of BasicDataTransmitRates from the example above, OperationalDataTransmitRates might be “1,2,5.5,11”, indicating that unicast frames can additionally be transmitted at 5.5 Mbps and 11 Mbps. - 1.0
PossibleDataTransmitRates string[](:256) R Comma-separated list (maximum number of characters 256) of strings. Data transmit rates for unicast frames at which the access point will permit a station to connect (a subset of OperationalDataTransmitRates). Given the values of BasicDataTransmitRates and OperationalDataTransmitRates from the examples above, PossibleDataTransmitRates might be “1,2,5.5”, indicating that the AP will only permit connections at 1 Mbps, 2 Mbps and 5.5 Mbps, even though it could theoretically accept connections at 11 Mbps. - 1.0
InsecureOOBAccessEnabled boolean W Indicates whether insecure write access via mechanisms other than the CPE WAN Management Protocol is permitted to the parameters in this object. - 1.0
BeaconAdvertisementEnabled boolean W Indicates whether or not the access point is sending out beacons. - 1.0
SSIDAdvertisementEnabled boolean W Indicates whether or not beacons include the SSID name. This parameter has an effect only if BeaconAdvertisementEnabled is true. - 1.0
RadioEnabled boolean W Indicates whether or not the access point radio is enabled. - 1.0
TransmitPowerSupported unsignedInt(0:100)[](:64) R Comma-separated list (maximum number of characters 64) of unsigned integers (0 to 100). Supported transmit power levels as percentages of full power. For example, “0,25,50,75,100”. - 1.0
AutoRateFallBackEnabled boolean W Indicates whether the access point can automatically reduce the data rate in the event of undue noise or contention. - 1.0
LocationDescription string(:4096) W An XML description of information used to identify the access point by name and physical location. The CPE is not expected to parse this string, but simply to treat it as an opaque string. An empty string indicates no location has been set. - 1.0
RegulatoryDomain string(:3) W 802.11d Regulatory Domain String. First two octets are ISO/IEC 3166-1 two-character country code. The third octet is either “ “ (all environments), “O” (outside) or “I” (inside). - 1.0
TotalPSKFailures unsignedInt R

The number of times pre-shared key (PSK) authentication has failed (relevant only to WPA and 802.11i).

Active Notification requests for this parameter MAY be denied.

- 1.0
TotalIntegrityFailures unsignedInt R

The number of times the MICHAEL integrity check has failed (relevant only to WPA and 802.11i)

Active Notification requests for this parameter MAY be denied.

- 1.0
ChannelsInUse string[](:1024) R

Comma-separated list (maximum number of characters 1024) of strings. Channels that the access point determines to be currently in use (including any that it is using itself). Ranges in the form “n-m” are permitted.

Active Notification requests for this parameter MAY be denied.

- 1.0
DeviceOperationMode string(:31) W

The current access-point operating mode. The OPTIONAL modes permit the AP to be configured as a wireless bridge (to bridge two wired networks), repeater (a bridge that also serves wireless clients), or wireless station. Ad hoc stations are not supported.

Enumeration of:

  • InfrastructureAccessPoint
  • WirelessBridge (OPTIONAL)
  • WirelessRepeater (OPTIONAL)
  • WirelessStation (OPTIONAL)
- 1.0
DistanceFromRoot unsignedInt W The number of hops from the root access point to the wireless repeater or bridge. - 1.0
PeerBSSID string W The MAC address of the peer in wireless repeater or bridge mode. - 1.0
AuthenticationServiceMode string W

Indicates whether another service is involved in client authentication (LinkAuthentication for a co-located authentication server; RadiusClient for an external RADIUS server).

Enumeration of:

  • None
  • LinkAuthentication (OPTIONAL)
  • RadiusClient (OPTIONAL)
- 1.0
WMMSupported boolean R Indicates whether this interface supports WiFi Multimedia (WMM) Access Categories (AC). - 1.0
TotalBytesSent unsignedInt R

The total number of bytes transmitted out of the interface, including framing characters. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
TotalBytesReceived unsignedInt R

The total number of bytes received on the interface, including framing characters. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
TotalPacketsSent unsignedInt R

The total number of packets transmitted out of the interface. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
TotalPacketsReceived unsignedInt R

The total number of packets which were received on this interface. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
TotalAssociations unsignedInt R

The number of devices currently associated with the access point. This corresponds to the number of entries in the AssociatedDevice table.

Active Notification requests for this parameter MAY be denied.

- 1.0
AutoChannelEnable boolean W Enable or disable automatic channel selection. Set to false to disable the automatic channel selection procedure, in which case the currently selected channel remains selected. Set to true to enable the automatic channel selection procedure. This procedure MUST automatically select the channel, and MAY also change it subsequently. AutoChannelEnable MUST automatically change to false whenever the channel is manually selected, i.e. whenever the Channel parameter is written. Whenever AutoChannelEnable is true, the value of the Channel parameter MUST be the channel selected by the automatic channel selection procedure. - 1.0
TransmitPower unsignedInt(0:100) W Indicates the current transmit power level as a percentage of full power. The value MUST be one of the values reported by the TransmitPowerSupported parameter. - 1.0
UAPSDSupported boolean R Indicates whether this interface supports WMM Unscheduled Automatic Power Save Delivery (U-APSD). Note: U-APSD support implies WMM support. - 1.0
WMMEnable boolean W Whether WMM support is currently enabled. When enabled, this is indicated in beacon frames - 1.0
UAPSDEnable boolean W Whether U-APSD support is currently enabled. When enabled, this is indicated in beacon frames. Note: U-APSD can only be enabled if WMM is also enabled. - 1.0
InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.AssociatedDevice.{i}. object(0:) R

A table of the devices currently associated with the access point. The size of this table is given by InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.TotalAssociations. This object MUST be implemented for CPE that contain an 802.11 interface on the LAN side.

At most one entry in this table can exist with a given value for AssociatedDeviceMACAddress.

- 1.0
AssociatedDeviceMACAddress string(:17) R

[MACAddress] The MAC address of an associated device.

Active Notification requests for this parameter MAY be denied.

- 1.0
AssociatedDeviceIPAddress string(:64) R

The IP address or DNS name of an associated device.

Active Notification requests for this parameter MAY be denied.

- 1.0
AssociatedDeviceAuthenticationState boolean R

Whether an associated device has authenticated (true) or not (false).

Active Notification requests for this parameter MAY be denied.

- 1.0
LastRequestedUnicastCipher string(:256) R

The unicast cipher that was most recently used for a station with a specified MAC address (802.11i only).

Active Notification requests for this parameter MAY be denied.

- 1.0
LastRequestedMulticastCipher string(:256) R

The multicast cipher that was most recently used for a station with a specified MAC address (802.11i only).

Active Notification requests for this parameter MAY be denied.

- 1.0
LastPMKId string(:256) R

The pairwise master key (PMK) that was most recently used for a station with a specified MAC address (802.11i only).

Active Notification requests for this parameter MAY be denied.

- 1.0
LastDataTransmitRate string(:4) R

The data transmit rate that was most recently used for a station with a specified MAC address.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.WEPKey.{i}. object(4:4) R

This is a table of WEP keys. The size of this table is fixed with exactly 4 entries (with instance numbers 1 through 4). This object MUST be implemented for CPE that contain an 802.11 interface on the LAN side.

This table MUST contain exactly 4 entries.

- 1.0
WEPKey string(:128) W

A WEP key expressed as a hexadecimal string. The WEP encryption level for a given key is inferred from the key length, e.g. 10 characters for 40-bit encryption, or 26 characters for 104-bit encryption (keys do not all have to be of the same length, although they will be if the CPE uses InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.KeyPassphrase to generate them). If InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.KeyPassphrase is written, all four WEP keys are immediately generated. The ACS SHOULD NOT set the passphrase and also set the WEP keys directly (the result of doing this is undefined).

When read, this parameter returns an empty string, regardless of the actual value.

- 1.0
InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.PreSharedKey.{i}. object(10:10) R

This is a table of preshared keys. The size of this table is fixed with exactly 10 entries (with instance numbers 1 through 10). This object MUST be implemented for CPE that contain an 802.11 interface on the LAN side.

This table MUST contain exactly 10 entries.

- 1.0
PreSharedKey string(:64) W

A literal WPA PSK expressed as a hexadecimal string. The first table entry contains the default PreSharedKey (InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.PreSharedKey.1.PreSharedKey). If KeyPassphrase is written, the PSK is immediately generated. The ACS SHOULD NOT set the passphrase and also set the PSK directly (the result of doing this is undefined).

When read, this parameter returns an empty string, regardless of the actual value.

- 1.0
KeyPassphrase string(:63) W

A passphrase from which the PSK is to be generated. The first table entry is the same as the parameter InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.KeyPassphrase for the same instance of WLANConfiguration. When either parameter is changed, the value of the other is changed as well. If KeyPassphrase is written, the PSK is immediately generated. The ACS SHOULD NOT set the passphrase and also set the PSK directly (the result of doing this is undefined). The key is generated as specified by WPA, which uses PBKDF2 from PKCS #5: Password-based Cryptography Specification Version 2.0 (RFC 2898 [RFC2898]).

When read, this parameter returns an empty string, regardless of the actual value.

- 1.0
AssociatedDeviceMACAddress string(:17) W [MACAddress] The MAC address associated with a preshared key, or an empty string if no MAC address is associated with the key. - 1.0
InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.Stats. object R This object contains statistics for an 802.11 LAN interface on a CPE device. Note that these statistics refer to the link layer, not to the physical layer. Note that this object does not include the total byte and packet statistics, which are, for historical reasons, in the parent object. - 1.0
ErrorsSent unsignedInt R

The total number of outbound packets that could not be transmitted because of errors. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
ErrorsReceived unsignedInt R

The total number of inbound packets that contained errors preventing them from being deliverable. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
UnicastPacketsSent unsignedInt R

The total number of packets requested for transmission which were not addressed to a multicast or broadcast address, including those that were discarded or not sent. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
UnicastPacketsReceived unsignedInt R

The total number of received packets which were not addressed to a multicast or broadcast address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
DiscardPacketsSent unsignedInt R

The total number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
DiscardPacketsReceived unsignedInt R

The total number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable. One possible reason for discarding such a packet could be to free up buffer space. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
MulticastPacketsSent unsignedInt R

The total number of packets requested for transmission which were addressed to a multicast address, including those that were discarded or not sent. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
MulticastPacketsReceived unsignedInt R

The total number of received packets which were addressed to a multicast address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
BroadcastPacketsSent unsignedInt R

The total number of packets requested for transmission which were addressed to a broadcast address, including those that were discarded or not sent. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
BroadcastPacketsReceived unsignedInt R

The total number of received packets which were addressed to a broadcast address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
UnknownProtoPacketsReceived unsignedInt R

The total number of packets received via the interface which were discarded because of an unknown or unsupported protocol. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.WPS. object R This object contains parameters related to WPS (Wi-Fi Protected Setup) [WPSv1.0] that apply to a CPE acting as an Access Point. - 1.0
Enable boolean W Enables or disables WPS functionality for this interface. - 1.0
DeviceName string(:32) R User-friendly description of the device. This parameter corresponds directly to the “Device Name” attribute of the WPS specification [WPSv1.0]. - 1.0
DevicePassword unsignedInt W

Represents the DevicePassword used (commonly known as PIN). This parameter corresponds directly to the “Device Password” attribute of the WPS specification [WPSv1.0].

When read, this parameter returns 0, regardless of the actual value.

- 1.0
UUID string(:36) R

UUID of the device. This is represented as specified in RFC 4122 [RFC4122] but omitting the leading “urn:uuid:”, e.g. “f81d4fae-7dec-11d0-a765-00a0c91e6bf6”. This parameter corresponds directly to the “UUID-E” (enrollee) and “UUID-R” (registrar) attributes of the WPS specification [WPSv1.0]. Note that if the Access Point can act both as an enrollee and as a registrar then UUID-E and UUID-R will be the same as each other.

Possible patterns:

  • [0-9A-Fa-f]{8}-([0-9A-Fa-f]{4}-){3}[0-9A-Fa-f]{12}
- 1.0
Version unsignedInt R The Wi-Fi Protected Setup version supported by the device. This parameter corresponds directly to the “Version” attribute of the WPS specification [WPSv1.0]. - 1.0
ConfigMethodsSupported string[] R

Comma-separated list of strings. WPS configuration methods supported by the device. Each list item is an enumeration of:

  • USBFlashDrive
  • Ethernet
  • Label
  • Display
  • ExternalNFCToken
  • IntegratedNFCToken
  • NFCInterface
  • PushButton
  • Keypad This parameter corresponds directly to the “Config Methods” attribute of the WPS specification [WPSv1.0].
- 1.0
ConfigMethodsEnabled string[] W Comma-separated list of strings. Each list item MUST be a member of the list reported by the ConfigMethodsSupported parameter. WPS configuration methods enabled on the device. This parameter corresponds directly to the “Permitted Config Methods” attribute of the WPS specification [WPSv1.0]. - 1.0
SetupLockedState string R

Indicates if the AP Setup mode is enabled for configuration of the AP through an external registrar. The AP Setup mode can be disabled by the user, by the remote management or in case of a brute force attack against the AP’s PIN (Wrong PIN provided to AP multiple times). Enumeration of:

  • Unlocked
  • LockedByLocalManagement
  • LockedByRemoteManagement
  • PINRetryLimitReached This parameter corresponds directly to the “AP Setup Locked” attribute of the WPS specification [WPSv1.0]. The factory default setting is Unlocked.
- 1.0
SetupLock boolean W When set to true, the Access Point will refuse to accept new external registrars; already established registrars will continue to be able to add new enrollees (the SetupLockedState becomes LockedByRemoteManagement). When set to false, the Access Point is enabled for configuration through an external registrar (the SetupLockedState becomes Unlocked). The factory default setting is false. - 1.0
ConfigurationState string R

Description of the WPS status on the Wireless Access Point side. Enumeration of:

  • Not configured (WLAN interface is unconfigured: out-of-the box configuration)
  • Configured (WLAN interface is configured) This parameter corresponds directly to the “Wi-Fi Protected Setup State” attribute of the WPS specification [WPSv1.0].
- 1.0
LastConfigurationError string R

Shows the result of the last external registrar attempt to configure the Access Point. Enumeration of:

  • NoError
  • DecryptionCRCFailure
  • SignalTooWeak
  • CouldntConnectToRegistrar
  • RogueActivitySuspected
  • DeviceBusy
  • SetupLocked
  • MessageTimeout
  • RegistrationSessionTimeout
  • DevicePasswordAuthFailure If no external registrar has yet attempted to configure the Access Point, this parameter MUST have the value NoError. The value of this parameter MUST persist across CPE reboots. This parameter corresponds directly to the “Configuration Error” attribute of the WPS specification [WPSv1.0].
- 1.0
RegistrarNumberOfEntries unsignedInt R Number of entries in the Registrar table: number of Registrars that currently have an association with the Access Point. This parameter corresponds directly to the “Registrar Current” attribute of the WPS specification [WPSv1.0]. - 1.0
RegistrarEstablished boolean R true if the Access Point has ever previously created an association with a Registrar. This parameter corresponds directly to the “Registrar Established” attribute of the WPS specification [WPSv1.0]. The factory default setting is false. - 1.0
InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.WPS.Registrar.{i}. object(0:) R

This table lists the Registrars associated with the Access Point. This table MUST persist across CPE reboots. The registrar UUID is the unique key. This object corresponds directly to the “Registrar List” attribute of the WPS specification [WPSv1.0].

At most one entry in this table can exist with a given value for UUID.

- 1.0
Enable boolean W If true, the registrar can be used by the Access Point for WPS procedures. - 1.0
UUID string(:36) R

UUID of the registrar. This is represented as specified in RFC 4122 [RFC4122] but omitting the leading “urn:uuid:”, e.g. f81d4fae-7dec-11d0-a765-00a0c91e6bf6. This parameter corresponds directly to the “UUID-R” attribute of the WPS specification [WPSv1.0].

Possible patterns:

  • [0-9A-Fa-f]{8}-([0-9A-Fa-f]{4}-){3}[0-9A-Fa-f]{12}
- 1.0
DeviceName string(:32) R Device Name of the registrar. This parameter corresponds directly to the “Device Name” attribute of the WPS specification [WPSv1.0]. - 1.0
InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.APWMMParameter.{i}. object(4:4) R

This is a table of WMM parameters for traffic that originates at the wireless access point, i.e. for outgoing traffic. The size of this table is fixed, with 4 entries (with instance numbers 1 through 4). Instance numbers MUST be assigned as follows:

  1. BE AC (Best Effort)
  2. BK AC (Background)
  3. VI AC (Video)
  4. VO AC (Voice)

This table MUST contain exactly 4 entries.

- 1.0
AIFSN unsignedInt(2:15) W Arbitration Inter Frame Spacing (Number). This is the number of time slots in the arbitration interframe space. - 1.0
ECWMin unsignedInt(0:15) W Exponent of Contention Window (Minimum). This encodes the Values of CWMin as an exponent: CWMin = 2ECWMin - 1. For example, if ECWMin is 8, then CWMin is 28 - 1, or 255, - 1.0
ECWMax unsignedInt(0:15) W Exponent of Contention Window (Maximum). This encodes the Values of CWMax as an exponent: CWMax = 2ECWMax - 1. For example, if ECWMax is 8, then CWMax is 28 - 1, or 255, - 1.0
TXOP unsignedInt(0:255) W Transmit Opportunity, in multiples of 32 microseconds. - 1.0
AckPolicy boolean W Ack Policy, where false=Do Not Acknowledge and true=Acknowledge. - 1.0
InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.STAWMMParameter.{i}. object(4:4) R

This is a table of WMM parameters for traffic that originates at the wireless station, i.e. for incoming traffic. The size of this table is fixed, with 4 entries (with instance numbers 1 through 4). Instance numbers MUST be assigned as follows:

  1. BE AC (Best Effort)
  2. BK AC (Background)
  3. VI AC (Video)
  4. VO AC (Voice)

This table MUST contain exactly 4 entries.

- 1.0
AIFSN unsignedInt(2:15) W Arbitration Inter Frame Spacing (Number). This is the number of time slots in the arbitration interframe space. - 1.0
ECWMin unsignedInt(0:15) W Exponent of Contention Window (Minimum). This encodes the Values of CWMin as an exponent: CWMin = 2ECWMin - 1. For example, if ECWMin is 8, then CWMin is 28 - 1, or 255, - 1.0
ECWMax unsignedInt(0:15) W Exponent of Contention Window (Maximum). This encodes the Values of CWMax as an exponent: CWMax = 2ECWMax - 1. For example, if ECWMax is 8, then CWMax is 28 - 1, or 255, - 1.0
TXOP unsignedInt(0:255) W Transmit Opportunity, in multiples of 32 microseconds. - 1.0
AckPolicy boolean W Ack Policy, where false=Do Not Acknowledge and true=Acknowledge. - 1.0
InternetGatewayDevice.LANDevice.{i}.Hosts. object R This object provides information about each of the hosts on the LAN, including those whose IP address was allocated by the CPE using DHCP as well as hosts with statically allocated IP addresses. - 1.0
HostNumberOfEntries unsignedInt R Number of entries in the Host table. - 1.0
InternetGatewayDevice.LANDevice.{i}.Hosts.Host.{i}. object(0:) R

Host table.

At most one entry in this table can exist with a given value for MACAddress.

- 1.0
IPAddress string(:45) R [IPAddress] Current IP Address of the host. - 1.0
AddressSource string R

Indicates whether the IP address of the host was allocated by the CPE using DHCP, was assigned to the host statically, or was assigned using automatic IP address allocation.

Enumeration of:

  • DHCP
  • Static
  • AutoIP
- 1.0
LeaseTimeRemaining int(-1:) R

DHCP lease time remaining in seconds. A value of -1 indicates an infinite lease. The value MUST be 0 (zero) if the AddressSource is not DHCP.

Active Notification requests for this parameter MAY be denied.

- 1.0
MACAddress string(:17) R [MACAddress] MAC address of the host. - 1.0
Layer2Interface string(:256) R This parameter is the full hierarchical parameter name of a particular LAN**InterfaceConfig object or a WLANConfiguration object. For example: InternetGatewayDevice.LANDevice.1.LANEthernetInterfaceConfig.2. In the case of an embedded Ethernet switch, the Layer2Interface parameter references the LANEthernetInterfaceConfig object that corresponds to the switch port the device is connected to (a LANEthernetInterfaceConfig instance for each switch port). In the case of an embedded WLAN access point, the Layer2Interface parameter references the WLANConfiguration object that corresponds to the SSID the device is connected to (if the access point supports multiple SSIDs, then each SSID is a separate instance). - 1.0
HostName string(:64) R The device’s host name or an empty string if unknown. - 1.0
InterfaceType string R

Type of physical interface through which this host is connected to the CPE.

Enumeration of:

  • Ethernet
  • USB
  • 802.11
  • HomePNA
  • HomePlug
  • MoCA
  • Other
- 1.0
Active boolean R Whether or not the host is currently present on the LAN. The method of presence detection is a local matter to the CPE. The ability to list inactive hosts is OPTIONAL. If the CPE includes inactive hosts in this table, this variable MUST be set to false for each inactive host. The length of time an inactive host remains listed in this table is a local matter to the CPE. - 1.0
VendorClassID string(:256) R Vendor Class Identifier DHCP option (Option 60) of the host. It MAY be defined when AddressSource is DHCP. An empty string indicates this option is not used. - 1.0
ClientID string(:256) R Client Identifier DHCP option (Option 61) for the specific IP connection of the client. The option value is binary, so an exact match is REQUIRED. It MAY be defined when AddressSource is DHCP. An empty string indicates this option is not used. - 1.0
UserClassID string(:256) R User Class Identifier DHCP option (Option 77) of the host. It MAY be defined when AddressSource is DHCP. An empty string indicates this option is not used. - 1.0
InternetGatewayDevice.WANDevice.{i}. object(0:) R Each instance contains all objects associated with a particular physical WAN interface. - 1.0
WANConnectionNumberOfEntries unsignedInt R Number of instances of WANConnectionDevice in this WANDevice. - 1.0
InternetGatewayDevice.WANDevice.{i}.WANCommonInterfaceConfig. object R This object models WAN interface properties common across all connection instances. - 1.0
EnabledForInternet boolean W Used to enable or disable access to and from the Internet across all connection instances. - 1.0
WANAccessType string R

Specifies the WAN access (modem) type.

Enumeration of:

  • DSL
  • Ethernet
  • POTS
- 1.0
Layer1UpstreamMaxBitRate unsignedInt R Specifies the maximum upstream theoretical bit rate for the WAN device in bits per second. This describes the maximum possible rate given the type of interface assuming the best-case operating environment, regardless of the current operating rate. For example, if the physical interface is 100BaseT, this value would be 100000000, regardless of the current operating rate. - 1.0
Layer1DownstreamMaxBitRate unsignedInt R Specifies the maximum downstream theoretical bit rate for the WAN device in bits per second. This describes the maximum possible rate given the type of interface assuming the best-case operating environment, regardless of the current operating rate. For example, if the physical interface is 100BaseT, this value would be 100000000, regardless of the current operating rate. - 1.0
PhysicalLinkStatus string R

Indicates the state of the physical connection (link) from WANDevice to a connected entity.

Enumeration of:

  • Up
  • Down
  • Initializing
  • Unavailable
- 1.0
WANAccessProvider string(:256) R Name of the Service Provider providing link connectivity on the WAN. - 1.0
TotalBytesSent unsignedInt R

The cumulative counter for total number of bytes sent upstream across all connection service instances on the WAN device.

Active Notification requests for this parameter MAY be denied.

- 1.0
TotalBytesReceived unsignedInt R

The cumulative counter for total number of bytes received downstream across all connection service instances on the WAN device.

Active Notification requests for this parameter MAY be denied.

- 1.0
TotalPacketsSent unsignedInt R

The cumulative counter for total number of packets (IP or PPP) sent upstream across all connection service instances on the WAN device.

Active Notification requests for this parameter MAY be denied.

- 1.0
TotalPacketsReceived unsignedInt R

The cumulative counter for total number of packets (IP or PPP) received downstream across all connection service instances on the WAN device.

Active Notification requests for this parameter MAY be denied.

- 1.0
MaximumActiveConnections unsignedInt R

Indicates the maximum number of active connections the CPE can simultaneously support.

Active Notification requests for this parameter MAY be denied.

- 1.0
NumberOfActiveConnections unsignedInt R Number of WAN connection service instances currently active on this WAN interface. - 1.0
InternetGatewayDevice.WANDevice.{i}.WANCommonInterfaceConfig.Connection.{i}. object(0:) R

Active connection table.

At most one entry in this table can exist with a given value for ActiveConnectionServiceID.

- 1.0
ActiveConnectionDeviceContainer string(:256) R Specifies a WAN connection device object associated with this connection instance. The content is the full hierarchical parameter name of the WAN connection device. Example: InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2. - 1.0
ActiveConnectionServiceID string(:256) R Specifies a WAN connection object associated with this connection instance. The content is the full hierarchical parameter name of the layer 3 connection object. Example: InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANPPPConnection.1. - 1.0
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig. object(0:1) R

This object models physical layer properties specific to a single physical connection of a DSL modem used for Internet access on a CPE. This object is required for a CPE with a DSL modem WAN interface, and is exclusive of any other WANInterfaceConfig* object within a given WANDevice instance.

This object is a member of a union, i.e., it is a member of a group of objects of which only one can exist at a given time.

- 1.0
Enable boolean W Enables or disables the link. - 1.0
Status string R

Status of the DSL physical link.

Enumeration of:

  • Up
  • Initializing
  • EstablishingLink
  • NoSignal
  • Error (OPTIONAL)
  • Disabled The Error value MAY be used by the CPE to indicate a locally defined error condition.
- 1.0
LinkEncapsulationSupported string[] R

Comma-separated list of strings. Indicates which link encapsulation standards and recommendations are supported by the B-NT.

Each list item is an enumeration of:

  • G.992.3_Annex_K_ATM
  • G.992.3_Annex_K_PTM
  • G.993.2_Annex_K_ATM
  • G.993.2_Annex_K_PTM
  • G.994.1 (Auto)
- 1.0
ModulationType string R

Indicates the type of modulation used on the connection.

Enumeration of:

  • ADSL_G.dmt
  • ADSL_G.lite
  • ADSL_G.dmt.bis
  • ADSL_re-adsl
  • ADSL_2plus
  • ADLS_four
  • ADSL_ANSI_T1.413
  • G.shdsl
  • IDSL
  • HDSL
  • SDSL
  • VDSL This parameter, which was inherited from WANDSLLinkConfig, is DEPRECATED because it is in general not clear which standards correspond to which of the the above enumerated values. It is RECOMMENDED that the StandardUsed parameter be used to indicate which standard is in use.
- 1.0
LineEncoding string R

The line encoding method used in establishing the Layer 1 DSL connection between the CPE and the DSLAM. Note: Generally speaking, this variable does not change after provisioning.

Enumeration of:

  • DMT
  • CAP
  • 2B1Q
  • 43BT
  • PAM
  • QAM
- 1.0
AllowedProfiles string[] R

Comma-separated list of strings. Indicates which VDSL2 profiles are allowed on the line. Each list item is an enumeration of:

  • 8a
  • 8b
  • 8c
  • 8d
  • 12a
  • 12b
  • 17a
  • 17b
  • 30a Note: In G.997.1, this parameter is called PROFILES. See ITU-T Recommendation G.997.1. Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be an empty string.
- 1.0
DataPath string R

Indicates whether the data path is fast (lower latency) or interleaved (lower error rate).

Enumeration of:

  • Interleaved
  • Fast
  • None Note1: This parameter is only applicable to G.992.1. Note2: For an ADSL1-capable multimode device operating in a mode other than ADSL1, the value of this parameter SHOULD be set to None.
- 1.0
InterleaveDepth unsignedInt R ADSL1 Interleaved depth. This variable is only applicable to ADSL1 and only if DataPath = Interleaved. Otherwise, the value of this parameter MUST be zero. - 1.0
LineNumber int(1:) R Signifies the line pair that the modem is using to connection. LineNumber = 1 is the innermost pair. - 1.0
UpstreamCurrRate unsignedInt R

The current physical layer aggregate data rate (expressed in Kbps) of the upstream DSL connection.

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, it MUST have the value 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
DownstreamCurrRate unsignedInt R

The current physical layer aggregate data rate (expressed in Kbps) of the downstream DSL connection.

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, it MUST have the value 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
UpstreamMaxRate unsignedInt R

The current attainable rate (expressed in Kbps) of the upstream DSL channel.

Note: This parameter is related to the G.997.1 parameter ATTNDRus, which is measured in bits/s. See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
DownstreamMaxRate unsignedInt R

The current attainable rate (expressed in Kbps) of the downstream DSL channel.

Note: This parameter is related to the G.997.1 parameter ATTNDRds, which is measured in bits/s. See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
UpstreamNoiseMargin int R

The current signal-to-noise ratio margin (expressed in 0.1 dB) in the upstream direction. Note: In G.997.1, this parameter is called SNRMus. See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
DownstreamNoiseMargin int R

The current signal-to-noise ratio margin (expressed in 0.1 dB) in the downstream direction. Note: In G.997.1, this parameter is called SNRMds. See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
UpstreamAttenuation int R

The current upstream signal loss (expressed in 0.1 dB).

Active Notification requests for this parameter MAY be denied.

- 1.0
DownstreamAttenuation int R

The current downstream signal loss (expressed in 0.1 dB).

Active Notification requests for this parameter MAY be denied.

- 1.0
UpstreamPower int R

The current output power at the CPE’s DSL interface (expressed in 0.1 dBmV).

Active Notification requests for this parameter MAY be denied.

- 1.0
DownstreamPower int R

The current received power at the CPE’s DSL interface (expressed in 0.1 dBmV).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATURVendor string(:8) R

ATU-R vendor identifier as defined in G.994.1 and T1.413. In the case of G.994.1 this corresponds to the four-octet provider code, which MUST be represented as eight hexadecimal digits.

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, it MUST have the value “00000000”.

- 1.0
ATURCountry string(:4) R

T.35 country code of the ATU-R vendor as defined in G.994.1, where the two-octet value defined in G.994.1 MUST be represented as four hexadecimal digits.

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, it MUST have the value “0000”.

- 1.0
ATURANSIStd unsignedInt R

ATU-R T1.413 Revision Number as defined in T1.413 Issue 2.

When T1.413 modulation is not in use, the parameter value SHOULD be 0.

- 1.0
ATURANSIRev unsignedInt R

ATU-R Vendor Revision Number as defined in T1.413 Issue 2.

When T1.413 modulation is not in use, the parameter value SHOULD be 0.

- 1.0
ATUCVendor string(:8) R

ATU-C vendor identifier as defined in G.994.1 and T1.413. In the case of G.994.1 this corresponds to the four-octet provider code, which MUST be represented as eight hexadecimal digits.

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, it MUST have the value “00000000”.

- 1.0
ATUCCountry string(:4) R

T.35 country code of the ATU-C vendor as defined in G.994.1, where the two-octet value defined in G.994.1 MUST be represented as four hexadecimal digits.

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, it MUST have the value “0000”.

- 1.0
ATUCANSIStd unsignedInt R

ATU-C T1.413 Revision Number as defined in T1.413 Issue 2.

When T1.413 modulation is not in use, the parameter value SHOULD be 0.

- 1.0
ATUCANSIRev unsignedInt R

ATU-C Vendor Revision Number as defined in T1.413 Issue 2.

When T1.413 modulation is not in use, the parameter value SHOULD be 0.

- 1.0
TotalStart unsignedInt R

Number of seconds since the beginning of the period used for collection of Total statistics. Statistics SHOULD continue to be accumulated across CPE reboots, though this might not always be possible.

Active Notification requests for this parameter MAY be denied.

- 1.0
ShowtimeStart unsignedInt R

Number of seconds since the most recent DSL Showtime - the beginning of the period used for collection of Showtime statistics. Showtime is defined as successful completion of the DSL link establishment process. The Showtime statistics are those collected since the most recent establishment of the DSL link.

Active Notification requests for this parameter MAY be denied.

- 1.0
LastShowtimeStart unsignedInt R

Number of seconds since the second most recent DSL Showtime-the beginning of the period used for collection of LastShowtime statistics. If the CPE has not retained information about the second most recent Showtime (e.g., on reboot), the start of LastShowtime statistics MAY temporarily coincide with the start of Showtime statistics.

Active Notification requests for this parameter MAY be denied.

- 1.0
CurrentDayStart unsignedInt R

Number of seconds since the beginning of the period used for collection of CurrentDay statistics. The CPE MAY align the beginning of each CurrentDay interval with days in the UTC time zone, but does not have to do so. Statistics SHOULD continue to be accumulated across CPE reboots, though this might not always be possible.

Active Notification requests for this parameter MAY be denied.

- 1.0
QuarterHourStart unsignedInt R

Number of seconds since the beginning of the period used for collection of QuarterHour statistics. The CPE MAY align the beginning of each QuarterHour interval with real-time quarter-hour intervals, but does not have to do so. Statistics SHOULD continue to be accumulated across CPE reboots, though this might not always be possible.

Active Notification requests for this parameter MAY be denied.

- 1.0
LinkEncapsulationRequested string W The value MUST be a member of the list reported by the LinkEncapsulationSupported parameter. Indicates the link encapsulation standard requested by the B-NT. - 1.0
LinkEncapsulationUsed string R

Indicates the link encapsulation standard that the B-NT is using for the connection. Enumeration of:

- 1.0
StandardsSupported string[] R

Comma-separated list of strings. Indicates which DSL standards and recommendations are supported by the B-NT.

Each list item is an enumeration of:

  • G.992.1_Annex_A
  • G.992.1_Annex_B
  • G.992.1_Annex_C
  • T1.413
  • T1.413i2
  • ETSI_101_388
  • G.992.2
  • G.992.3_Annex_A
  • G.992.3_Annex_B
  • G.992.3_Annex_C
  • G.992.3_Annex_I
  • G.992.3_Annex_J
  • G.992.3_Annex_L
  • G.992.3_Annex_M
  • G.992.4
  • G.992.5_Annex_A
  • G.992.5_Annex_B
  • G.992.5_Annex_C
  • G.992.5_Annex_I
  • G.992.5_Annex_J
  • G.992.5_Annex_M
  • G.993.1
  • G.993.1_Annex_A
  • G.993.2_Annex_A
  • G.993.2_Annex_B
  • G.993.2_Annex_C
- 1.0
StandardUsed string R The value MUST be a member of the list reported by the StandardsSupported parameter. Indicates the standard that the B-NT is using for the connection. - 1.0
CurrentProfile string R The value MUST be a member of the list reported by the AllowedProfiles parameter, or else be an empty string. Indicates which VDSL2 profile is currently in use on the line. Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be an empty string. - 1.0
PowerManagementState string R

The power management state of the line.

Enumeration of:

  • L0
  • L1
  • L3
  • L4
- 1.0
SuccessFailureCause unsignedInt(0:5) R The success failure cause of the initialization. An enumeration of the following integer values:
  • 0: Successful
  • 1: Configuration error. This error occurs with inconsistencies in configuration parameters, e.g. when the line is initialized in an xDSL Transmission system where an xTU does not support the configured Maximum Delay or the configured Minimum or Maximum Data Rate for one or more bearer channels.
  • 2: Configuration not feasible on the line. This error occurs if the Minimum Data Rate cannot be reached on the line with the Minimum Noise Margin, Maximum PSD level, Maximum Delay and Maximum Bit Error Ratio for one or more bearer channels.
  • 3: Communication problem. This error occurs, for example, due to corrupted messages or bad syntax messages or if no common mode can be selected in the G.994.1 handshaking procedure or due to a timeout..
  • 4: No peer xTU detected. This error occurs if the peer xTU is not powered or not connected or if the line is too long to allow detection of a peer xTU.
  • 5: Any other or unknown Initialization Failure cause.
- 1.0
LastStateTransmittedDownstream unsignedInt R This parameter represents the last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line. Initialization states are defined in the individual xDSL Recommendations and are counted from 0 (if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime. This parameter needs to be interpreted along with the xDSL Transmission System. This parameter is available only when, after a failed full initialization, the line diagnostics procedures are activated on the line. - 1.0
LastStateTransmittedUpstream unsignedInt R This parameter represents the last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line. Initialization states are defined in the individual xDSL Recommendations and are counted from 0 (if G.994.1 is used) or 1 (if G.994.1 is not used) up to Showtime. This parameter needs to be interpreted along with the xDSL Transmission System. This parameter is available only when, after a failed full initialization, the line diagnostics procedures are activated on the line. - 1.0
UPBOKLE unsignedInt(0:1280) R This parameter contains the estimated electrical loop length expressed in dB at 1MHz, kle (see O-UPDATE in section 12.2.4.2.1.2/G.993.2). The value SHALL be coded as an unsigned 16 bit number in the range 0 (coded as 0) to 128 dB (coded as 1280) in steps of 0.1 dB. - 1.0
MREFPSDds base64(0:145) R This parameter SHALL contain the set of breakpoints exchanged in the MREFPSDds fields of the O-PRM message of G.993.2. Base64 encoded of the binary representation defined in Table 12-19/G.993.2 (maximum length is 145 octets, which requires 196 bytes for Base64 encoding). - 1.0
MREFPSDus base64(0:145) R This parameter SHALL contain the set of breakpoints exchanged in the MREFPSDus fields of the R-PRM message of G.993.2. Base64 encoded of the binary representation defined in Table 12-19/G.993.2 (maximum length is 145 octets, which requires 196 bytes for Base64 encoding). - 1.0
LIMITMASK unsignedInt R Indicates the enabled VDSL2 Limit PSD mask of the selected PSD mask class. Bit mask as specified in ITU-T Recommendation G.997.1. Note: For a VDSL2-capable multimode device operating in a mode other than VDSL2, the value of this parameter SHOULD be set to 0. - 1.0
US0MASK unsignedInt R Indicates the allowed VDSL2 US0 PSD masks for Annex A operation. Bit mask as specified in see ITU-T Recommendation G.997.1. Note: For a VDSL2-capable multimode device operating in a mode other than VDSL2, the value of this parameter SHOULD be set to 0. - 1.0
LPATH unsignedInt R Reports the index of the latency path supporting the bearer channel. For single-latency connections, LPATH = 0. Note: See ITU-T Recommendation G.997.1. - 1.0
INTLVDEPTH int R Reports the interleaver depth D for the latency path indicated in LPATH. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to -1. - 1.0
INTLVBLOCK int R Reports the interleaver block length in use on the latency path indicated in LPATH. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to -1. - 1.0
ActualInterleavingDelay unsignedInt R Reports the actual delay, in milliseconds, of the latency path due to interleaving. Note: In G.997.1, this parameter is called “Actual Interleaving Delay.” See ITU-T Recommendation G.997.1. - 1.0
ACTINP int R Reports the actual impulse noise protection (INP) provided by the latency path indicated in LPATH. The value is the actual INP in the L0 (i.e., Showtime) state. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to -1. - 1.0
INPREPORT boolean R Reports whether the value reported in ACTINP was computed assuming the receiver does not use erasure decoding. Valid values are 0 (computed per the formula assuming no erasure decoding) and 1 (computed by taking into account erasure decoding capabilities of receiver). Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to false. - 1.0
NFEC int R Reports the size, in octets, of the Reed-Solomon codeword in use on the latency path indicated in LPATH. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to -1. - 1.0
RFEC int R Reports the number of redundancy bytes per Reed-Solomon codeword on the latency path indicated in LPATH. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to -1. - 1.0
LSYMB int R Reports the number of bits per symbol assigned to the latency path indicated in LPATH. This value does not include overhead due to trellis coding. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to -1. - 1.0
TRELLISds int R Reports whether trellis coding is enabled in the downstream direction. A value of 1 indicates that trellis coding is in use, and a value of 0 indicates that the trellis is disabled. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to -1. - 1.0
TRELLISus int R Reports whether trellis coding is enabled in the upstream direction. A value of 1 indicates that trellis coding is in use, and a value of 0 indicates that the trellis is disabled. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to -1. - 1.0
ACTSNRMODEds unsignedInt R Reports whether the OPTIONAL virtual noise mechanism is in use in the downstream direction. A value of 1 indicates the virtual noise mechanism is not in use, and a value of 2 indicates the virtual noise mechanism is in use. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0. - 1.0
ACTSNRMODEus unsignedInt R Reports whether the OPTIONAL virtual noise mechanism is in use in the upstream direction. A value of 1 indicates the virtual noise mechanism is not in use, and a value of 2 indicates the virtual noise mechanism is in use. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0. - 1.0
VirtualNoisePSDds base64(0:97) R Reports the virtual noise PSD for the downstream direction. Base64 encoded of the binary representation defined in G.997.1 by the parameter called TXREFVNds (maximum length is 97 octets, which requires 132 bytes for Base64 encoding). See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to an empty string. - 1.0
VirtualNoisePSDus base64(0:49) R Reports the virtual noise PSD for the upstream direction. Base64 encoded of the binary representation defined in G.997.1by the parameter called TXREFVNus (maximum length is 49 octets, which requires 68 bytes for Base64 encoding). See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to an empty string. - 1.0
ACTUALCE unsignedInt R Reports the actual cyclic extension, as the value of m, in use for the connection. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 99. - 1.0
SNRMpbus string[](:24) R Comma-separated list (maximum number of characters 24) of strings. The current signal-to-noise ratio margin of each upstream band. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1. - 1.0
SNRMpbds string[](:24) R Comma-separated list (maximum number of characters 24) of strings. The current signal-to-noise ratio margin of each band. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1. - 1.0
INMIATOds unsignedInt(3:511) R The Impulse Noise Monitoring (INM) Inter Arrival Time (IAT) Offset, measured in DMT symbols, that the xTU receiver uses to determine in which bin of the IAT histogram the IAT is reported. Note: In G.997.1, this parameter is called INMIATO. See ITU-T Recommendation G.997.1. - 1.0
INMIATSds unsignedInt(0:7) R The Impulse Noise Monitoring (INM) Inter Arrival Time (IAT) Step that the xTU receiver uses to determine in which bin of the IAT histogram the IAT is reported. Note: In G.997.1, this parameter is called INMIATS. See ITU-T Recommendation G.997.1. - 1.0
INMCCds unsignedInt(0:64) R The Impulse Noise Monitoring (INM) Cluster Continuation value, measured in DMT symbols, that the xTU receiver uses in the cluster indication process. Note: In G.997.1, this parameter is called INMCC. See ITU-T Recommendation G.997.1. - 1.0
INMINPEQMODEds unsignedInt(0:3) R The Impulse Noise Monitoring (INM) Equivalent Impulse Noise Protection (INP) Mode that the xTU receiver uses in the computation of the Equivalent INP. Note: In G.997.1, this parameter is called INM_INPEQ_MODE. See ITU-T Recommendation G.997.1. - 1.0
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.Stats. object R This object contains statistics for a WAN DSL physical interface. - 1.0
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.Stats.Total. object R This object contains DSL total statistics. - 1.0
ReceiveBlocks unsignedInt R

Total number of successfully received blocks, where a block is as defined in RFC 2662 [RFC2662]. This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
TransmitBlocks unsignedInt R

Total number of successfully transmitted blocks, where a block is as defined in RFC 2662 [RFC2662]. This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
CellDelin unsignedInt R

Total number of cell-delineation errors (total seconds with NCD or LCD failures as defined in ITU-T Rec. G.997.1).

This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
LinkRetrain unsignedInt R

Total number of link-retrain errors (Full Initialization Count as defined in ITU-T Rec. G.997.1).

This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
InitErrors unsignedInt R

Total number of initialization errors (LINIT failures as defined in ITU-T Rec. G.997.1).

This parameter is DEPRECATED because it is not defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
InitTimeouts unsignedInt R

Total number of initialization timeout errors.

Active Notification requests for this parameter MAY be denied.

- 1.0
LossOfFraming unsignedInt R

Total number of loss-of-framing errors (LOF failures as defined in ITU-T Rec. G.997.1).

This parameter is DEPRECATED because it is not defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
ErroredSecs unsignedInt R

Total number of errored seconds (ES-L as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
SeverelyErroredSecs unsignedInt R

Total number of severely errored seconds (SES-L as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
FECErrors unsignedInt R

Total number of FEC errors detected (FEC-C as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCFECErrors unsignedInt R

Total number of FEC errors detected by the ATU-C (FEC-CFE as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
HECErrors unsignedInt R

Total number of HEC errors detected (HEC-P as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCHECErrors unsignedInt R

Total number of HEC errors detected by the ATU-C (HEC-PFE as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
CRCErrors unsignedInt R

Total number of CRC errors detected (CV-C as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCCRCErrors unsignedInt R

Total number of CRC errors detected by the ATU-C (CV-CFE as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
LInit boolean R

LInit is a flag to signal that a failure occurred as defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
LOF boolean R

This parameter corresponds to LOF as defined in ITU-T Rec. G.997.1. LOF is a flag to signal that a failure occurred.

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCErroredSecs unsignedInt R

Total number of errored seconds detected by the ATU-C (ES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCSeverelyErroredSecs unsignedInt R

Total number of severely errored seconds detected by the ATU-C (SES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.Stats.Showtime. object R This object contains DSL statistics accumulated since the most recent DSL Showtime. - 1.0
ReceiveBlocks unsignedInt R

Number of successfully received blocks since the most recent DSL Showtime, where a block is as defined in RFC 2662 [RFC2662]. This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
TransmitBlocks unsignedInt R

Number of successfully transmitted blocks since the most recent DSL Showtime, where a block is as defined in RFC 2662 [RFC2662]. This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
CellDelin unsignedInt R

Number of cell-delineation errors since the most recent DSL Showtime (total seconds with NCD or LCD failures as defined in ITU-T Rec. G.997.1).

This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
LinkRetrain unsignedInt R

Number of link-retrain errors since the most recent DSL Showtime (Full Initialization Count as defined in ITU-T Rec. G.997.1).

This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
InitErrors unsignedInt R

Number of initialization errors since the most recent DSL Showtime (LINIT failures as defined in ITU-T Rec. G.997.1).

This parameter is DEPRECATED because it is not defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
InitTimeouts unsignedInt R

Number of initialization timeout errors since the most recent DSL Showtime.

Active Notification requests for this parameter MAY be denied.

- 1.0
LossOfFraming unsignedInt R

Number of loss-of-framing errors since the most recent DSL Showtime (LOF failures as defined in ITU-T Rec. G.997.1).

This parameter is DEPRECATED because it is not defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
ErroredSecs unsignedInt R

Number of errored seconds since the most recent DSL Showtime (ES-L as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
SeverelyErroredSecs unsignedInt R

Number of severely errored seconds since the most recent DSL Showtime (SES-L as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
FECErrors unsignedInt R

Number of FEC errors detected since the most recent DSL Showtime (FEC-C as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCFECErrors unsignedInt R

Number of FEC errors detected by the ATU-C since the most recent DSL Showtime (FEC-CFE as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
HECErrors unsignedInt R

Number of HEC errors detected since the most recent DSL Showtime (HEC-P as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCHECErrors unsignedInt R

Number of HEC errors detected by the ATU-C since the most recent DSL Showtime (HEC-PFE as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
CRCErrors unsignedInt R

Number of CRC errors detected since the most recent DSL Showtime (CV-C as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCCRCErrors unsignedInt R

Number of CRC errors detected by the ATU-C since the most recent DSL Showtime (CV-CFE as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
LInit boolean R

LInit is a flag to signal that a failure occurred as defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
LOF boolean R

This parameter corresponds to LOF as defined in ITU-T Rec. G.997.1. LOF is a flag to signal that a failure occurred.

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCErroredSecs unsignedInt R

Number of errored seconds since the most recent DSL Showtime detected by the ATU-C (ES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCSeverelyErroredSecs unsignedInt R

Number of severely errored seconds since the most recent DSL Showtime detected by the ATU-C (SES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.Stats.LastShowtime. object R This object contains DSL statistics accumulated since the second most recent DSL Showtime. - 1.0
ReceiveBlocks unsignedInt R

Number of successfully received blocks since the second most recent DSL Showtime, where a block is as defined in RFC 2662 [RFC2662]. This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
TransmitBlocks unsignedInt R

Number of successfully transmitted blocks since the second most recent DSL Showtime, where a block is as defined in RFC 2662 [RFC2662]. This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
CellDelin unsignedInt R

Number of cell-delineation errors since the second most recent DSL Showtime (total seconds with NCD or LCD failures as defined in ITU-T Rec. G.997.1).

This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
LinkRetrain unsignedInt R

Number of link-retrain errors since the second most recent DSL Showtime (Full Initialization Count as defined in ITU-T Rec. G.997.1).

This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
InitErrors unsignedInt R

Number of initialization errors since the second most recent DSL Showtime (LINIT failures as defined in ITU-T Rec. G.997.1).

This parameter is DEPRECATED because it is not defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
InitTimeouts unsignedInt R

Number of initialization timeout errors since the second most recent DSL Showtime.

Active Notification requests for this parameter MAY be denied.

- 1.0
LossOfFraming unsignedInt R

Number of loss-of-framing errors since the second most recent DSL Showtime (LOF failures as defined in ITU-T Rec. G.997.1).

This parameter is DEPRECATED because it is not defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
ErroredSecs unsignedInt R

Number of errored seconds since the second most recent DSL Showtime (ES-L as defined in ITU-T Rec. G.997.1).

Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
SeverelyErroredSecs unsignedInt R

Number of severely errored seconds since the second most recent DSL Showtime (SES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
FECErrors unsignedInt R

Number of FEC errors detected since the second most recent DSL Showtime (FEC-C as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCFECErrors unsignedInt R

Number of FEC errors detected by the ATU-C since the second most recent DSL Showtime (FEC-CFE as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
HECErrors unsignedInt R

Number of HEC errors detected since the second most recent DSL Showtime (HEC-P as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCHECErrors unsignedInt R

Number of HEC errors detected by the ATU-C since the second most recent DSL Showtime (HEC-PFE as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
CRCErrors unsignedInt R

Number of CRC errors detected since the second most recent DSL Showtime (CV-C as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCCRCErrors unsignedInt R

Number of CRC errors detected by the ATU-C since the second most recent DSL Showtime (CV-CFE as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
LInit boolean R

LInit is a flag to signal that a failure occurred as defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
LOF boolean R

This parameter corresponds to LOF as defined in ITU-T Rec. G.997.1. LOF is a flag to signal that a failure occurred.

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCErroredSecs unsignedInt R

Number of errored seconds since the second most recent DSL Showtime detected by the ATU-C (ES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCSeverelyErroredSecs unsignedInt R

Number of severely errored seconds since the second most recent DSL Showtime detected by the ATU-C (SES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.Stats.CurrentDay. object R This object contains DSL statistics accumulated during the current day. - 1.0
ReceiveBlocks unsignedInt R

Number of successfully received blocks during the current day, where a block is as defined in RFC 2662 [RFC2662]. This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
TransmitBlocks unsignedInt R

Number of successfully transmitted blocks during the current day, where a block is as defined in RFC 2662 [RFC2662]. This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
CellDelin unsignedInt R

Number of cell-delineation errors during the current day (total seconds with NCD or LCD failures as defined in ITU-T Rec. G.997.1). This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
LinkRetrain unsignedInt R

Number of link-retrain errors during the current day (Full Initialization Count as defined in ITU-T Rec. G.997.1). This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
InitErrors unsignedInt R

Number of initialization errors during the current day (LINIT failures as defined in ITU-T Rec. G.997.1). This parameter is DEPRECATED because it is not defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
InitTimeouts unsignedInt R

Number of initialization timeout errors during the current day.

Active Notification requests for this parameter MAY be denied.

- 1.0
LossOfFraming unsignedInt R

Number of loss-of-framing errors during the current day (LOF failures as defined in ITU-T Rec. G.997.1). This parameter is DEPRECATED because it is not defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
ErroredSecs unsignedInt R

Number of errored seconds during the current day (ES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
SeverelyErroredSecs unsignedInt R

Number of severely errored seconds during the current day (SES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
FECErrors unsignedInt R

Number of FEC errors detected during the current day (FEC-C as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCFECErrors unsignedInt R

Number of FEC errors detected by the ATU-C during the current day (FEC-CFE as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
HECErrors unsignedInt R

Number of HEC errors detected during the current day (HEC-P as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCHECErrors unsignedInt R

Number of HEC errors detected by the ATU-C during the current day (HEC-PFE as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
CRCErrors unsignedInt R

Number of CRC errors detected during the current day (CV-C as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCCRCErrors unsignedInt R

Number of CRC errors detected by the ATU-C during the current day (CV-CFE as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
LInit boolean R

LInit is a flag to signal that a failure occurred as defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
LOF boolean R

This parameter corresponds to LOF as defined in ITU-T Rec. G.997.1. LOF is a flag to signal that a failure occurred.

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCErroredSecs unsignedInt R

Number of errored seconds during the current day detected by the ATU-C (ES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCSeverelyErroredSecs unsignedInt R

Number of severely errored seconds during the current day detected by the ATU-C (SES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.Stats.QuarterHour. object R This object contains DSL statistics accumulated during the current quarter hour. - 1.0
ReceiveBlocks unsignedInt R

Number of successfully received blocks during the current quarter hour, where a block is as defined in RFC 2662 [RFC2662]. This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
TransmitBlocks unsignedInt R

Number of successfully transmitted blocks during the current quarter hour, where a block is as defined in RFC 2662 [RFC2662]. This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
CellDelin unsignedInt R

Number of cell-delineation errors during the current quarter hour (total seconds with NCD or LCD failures as defined in ITU-T Rec. G.997.1). This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
LinkRetrain unsignedInt R

Number of link-retrain errors during the current quarter hour (Full Initialization Count as defined in ITU-T Rec. G.997.1). This parameter is DEPRECATED because it is not available at either the G or the S/T interface.

Active Notification requests for this parameter MAY be denied.

- 1.0
InitErrors unsignedInt R

Number of initialization errors during the current quarter hour (LINIT failures as defined in ITU-T Rec. G.997.1). This parameter is DEPRECATED because it is not defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
InitTimeouts unsignedInt R

Number of initialization timeout errors during the current quarter hour.

Active Notification requests for this parameter MAY be denied.

- 1.0
LossOfFraming unsignedInt R

Number of loss-of-framing errors during the current quarter hour (LOF failures as defined in ITU-T Rec. G.997.1). This parameter is DEPRECATED because it is not defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
ErroredSecs unsignedInt R

Number of errored seconds during the current quarter hour (ES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
SeverelyErroredSecs unsignedInt R

Number of severely errored seconds during the current quarter hour (SES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
FECErrors unsignedInt R

Number of FEC errors detected during the current quarter hour (FEC-C as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCFECErrors unsignedInt R

Number of FEC errors detected by the ATU-C during the current quarter hour (FEC-CFE as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
HECErrors unsignedInt R

Number of HEC errors detected during the current quarter hour (HEC-P as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCHECErrors unsignedInt R

Number of HEC errors detected by the ATU-C during the current quarter hour (HEC-PFE as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
CRCErrors unsignedInt R

Number of CRC errors detected during the current quarter hour (CV-C as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCCRCErrors unsignedInt R

Number of CRC errors detected by the ATU-C during the current quarter hour (CV-CFE as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
LInit boolean R

LInit is a flag to signal that a failure occurred as defined in G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
LOF boolean R

This parameter corresponds to LOF as defined in ITU-T Rec. G.997.1. LOF is a flag to signal that a failure occurred.

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCErroredSecs unsignedInt R

Number of errored seconds during the current quarter hour detected by the ATU-C (ES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
ATUCSeverelyErroredSecs unsignedInt R

Number of severely errored seconds during the current quarter hour detected by the ATU-C (SES-L as defined in ITU-T Rec. G.997.1). Note: This parameter is OPTIONAL at the G and S/T interfaces in G.997.1 Amendment 1. If the parameter is implemented but no value is available, its value MUST be 4294967295 (the maximum for its data type).

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.TestParams. object R This object contains the DSL test parameters that are available during the L0 (i.e., Showtime) state. - 1.0
HLOGGds unsignedInt R

Number of sub-carriers per sub-carrier group in the downstream direction for HLOGpsds. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLOGGus unsignedInt R

Number of sub-carriers per sub-carrier group in the upstream direction for HLOGpsus. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLOGpsds string[](:2559) R

Comma-separated list (maximum number of characters 2559) of strings. Downstream logarithmic channel characteristics per sub-carrier group. The maximum number of elements is 256 for G.992.3, and 512 for G.992.5. For G.993.2, the number of elements will depend on the value of HLOGGds but will not exceed 512. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to None. Note: HLOGpsds is measured during initialization and is not updated during Showtime.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLOGpsus string[](:2559) R

Comma-separated list (maximum number of characters 2559) of strings. Upstream logarithmic channel characteristics per sub-carrier group. The maximum number of elements is 64 for G.992.3 and G.992.5. For G.993.2, the number of elements will depend on the value of HLOGGus but will not exceed 512. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to None. Note: HLOGpsus is measured during initialization and is not updated during Showtime.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLOGMTds unsignedInt R

Indicates the number of symbols over which HLOGpsds was measured. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLOGMTus unsignedInt R

Indicates the number of symbols over which HLOGpsus was measured. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
QLNGds unsignedInt R

Number of sub-carriers per sub-carrier group in the downstream direction for QLNpsds. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
QLNGus unsignedInt R

Number of sub-carriers per sub-carrier group in the upstream direction for QLNpsus. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
QLNpsds int[](:2047) R

Comma-separated list (maximum number of characters 2047) of integers. Downstream quiet line noise per subcarrier group. The maximum number of elements is 256 for G.992.3 and G.992.5. For G.993.2, the number of elements will depend on the value of QLNGds but will not exceed 512. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter should be set to None. Note: QLNpsds is measured during initialization and is not updated during Showtime.

Active Notification requests for this parameter MAY be denied.

- 1.0
QLNpsus string[](:2047) R

Comma-separated list (maximum number of characters 2047) of strings. Upstream quiet line noise per subcarrier group. The maximum number of elements is 64 for G.992.3 and G.992.5. For G.993.2, the number of elements will depend on the value of QLNGus but will not exceed 512. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter should be set to None. Note: QLNpsus is measured during initialization and is not updated during Showtime.

Active Notification requests for this parameter MAY be denied.

- 1.0
QLNMTds unsignedInt R

Indicates the number of symbols over which QLNpsds was measured. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
QLNMTus unsignedInt R

Indicates the number of symbols over which QLNpsus was measured. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
SNRGds unsignedInt R

Number of sub-carriers per sub-carrier group in the downstream direction for SNRpsds. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
SNRGus unsignedInt R

Number of sub-carriers per sub-carrier group in the upstream direction for SNRpsus. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
SNRpsds int[](:2047) R

Comma-separated list (maximum number of characters 2047) of integers. Downstream SNR per subcarrier group. The maximum number of elements is 256 for G.992.3, and 512 for G.992.5. For G.993.2, the number of elements will depend on the value of SNRGds but will not exceed 512. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter should be set to None. Note: SNRpsds is first measured during initialization and is updated during Showtime.

Active Notification requests for this parameter MAY be denied.

- 1.0
SNRpsus string[](:2047) R

Comma-separated list (maximum number of characters 2047) of strings. Upstream SNR per subcarrier group. The maximum number of elements is 64 for G.992.3 and G.992.5. For G.993.2, the number of elements will depend on the value of SNRGus but will not exceed 512. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter should be set to None. Note: SNRpsus is first measured during initialization and is updated during Showtime.

Active Notification requests for this parameter MAY be denied.

- 1.0
SNRMTds unsignedInt R

Indicates the number of symbols over which SNRpsds was measured. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
SNRMTus unsignedInt R

Indicates the number of symbols over which SNRpsus was measured. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
LATNds string[](:24) R

Comma-separated list (maximum number of characters 24) of strings. Downstream line attenuation per usable band, as computed during initialization. Number of elements is dependent on the number of downstream bands but will exceed one only for G.993.2. Interpretation of LATNds is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
LATNus string[](:24) R

Comma-separated list (maximum number of characters 24) of strings. Upstream line attenuation per usable band, as computed during initialization. Number of elements is dependent on the number of upstream bands but will exceed one only for G.993.2. Interpretation of LATNus is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
SATNds string[](:24) R

Comma-separated list (maximum number of characters 24) of strings. Downstream signal attenuation per usable band, as computed during the L0 (i.e., Showtime) state. Number of elements is dependent on the number of downstream bands but will exceed one only for G.993.2. Interpretation of SATNds is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
SATNus string[](:24) R

Comma-separated list (maximum number of characters 24) of strings. Upstream signal attenuation per usable band, as computed during the L0 (i.e., Showtime) state. Number of elements is dependent on the number of downstream bands but will exceed one only for G.993.2. Interpretation of SATNus is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.WANDevice.{i}.WANEthernetInterfaceConfig. object(0:1) R

This object models physical layer properties specific to a single Ethernet physical connection used for Internet access on a CPE. This object is required for a CPE with an Ethernet WAN interface, and is exclusive of any other WANInterfaceConfig* object within a given WANDevice instance. Note that this object is not related to the Ethernet protocol layer sometimes used in associated with a DSL connection.

This object is a member of a union, i.e., it is a member of a group of objects of which only one can exist at a given time.

- 1.0
Enable boolean W Enables or disables this interface. - 1.0
Status string R

Indicates the status of this interface.

Enumeration of:

  • Up
  • NoLink
  • Error (OPTIONAL)
  • Disabled The Error value MAY be used by the CPE to indicate a locally defined error condition.
- 1.0
MACAddress string(:17) R [MACAddress] The physical address of the interface. - 1.0
MaxBitRate string W

The maximum upstream and downstream bit rate available to this connection.

Enumeration of:

  • 10
  • 100
  • Auto (DELETED)
  • 1000
  • 10000
- 1.0
DuplexMode string W

The duplex mode available to this connection.

Enumeration of:

  • Half
  • Full
  • Auto
- 1.0
ShapingRate int(-1:) W Rate to shape this connection’s egress traffic to. For leaky bucket (constant rate shaping), this is the constant rate. For token bucket (variable rate shaping), this is the average rate. If <= 100, in percent of the rate of the highest rate-constrained layer over which the packet will travel on egress. If > 100, in bits per second. A value of -1 indicates no shaping. For example, for packets destined for a WAN DSL interface, if the ATM layer is rate-constrained, then the rate is calculated relative to this rate. Otherwise, the rate is calculated relative to the physical-layer DSL rate. - 1.0
ShapingBurstSize unsignedInt W Burst size in bytes. For both leaky bucket (constant rate shaping) and token bucket (variable rate shaping) this is the bucket size and is therefore the maximum burst size. - 1.0
InternetGatewayDevice.WANDevice.{i}.WANEthernetInterfaceConfig.Stats. object R This object contains statistics for an Ethernet WAN interface on a CPE device. - 1.0
BytesSent unsignedInt R

Total number of bytes sent over the interface since the CPE was last reset.

Active Notification requests for this parameter MAY be denied.

- 1.0
BytesReceived unsignedInt R

Total number of bytes received over the interface since the CPE was last reset.

Active Notification requests for this parameter MAY be denied.

- 1.0
PacketsSent unsignedInt R

Total number of packets sent over the interface since the CPE was last reset.

Active Notification requests for this parameter MAY be denied.

- 1.0
PacketsReceived unsignedInt R

Total number of packets received over the interface since the CPE was last reset.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.WANDevice.{i}.WANDSLConnectionManagement. object R This object is intended for a CPE with a DSL modem WAN interface. Note - This object was originally created to allow WANConnection devices and services to be added dynamically in the IGD object model in TR-064 because UPnP Device Architecture 1.0 did not contain this capability natively. Because in TR-069 objects can be created and removed using the AddObject and DeleteObject RPCs, WANConnection interfaces can be managed using these TR-069 mechanisms directly. Therefore, unlike the TR-064 equivalent, the ConnectionService table within this object is Read-Only in the TR-069 InternetGatewayDevice data model context. This object is OBSOLETED because it serves no purpose. - 1.0
ConnectionServiceNumberOfEntries unsignedInt R
Number of table entries in the ConnectionService table.
This parameter is OBSOLETED because it is within an OBSOLETED object. The CPE MAY return a value of 0 for this parameter, regardless of the number of connection services, in which case no ConnectionService instances will exist.
- 1.0
InternetGatewayDevice.WANDevice.{i}.WANDSLConnectionManagement.ConnectionService.{i}. object(0:) R
This table contains an entry for each connection service.
This object is OBSOLETED because it is within an OBSOLETED object.
At most one entry in this table can exist with a given value for WANConnectionService.
- 1.0
WANConnectionDevice string(:256) R
Specifies a WAN connection device object associated with this connection instance. The content is the full hierarchical parameter name of the WAN connection device. Example: InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.
This parameter is OBSOLETED because it is within an OBSOLETED object.
- 1.0
WANConnectionService string(:256) R
Specifies a WAN connection object associated with this connection instance. The content is the full hierarchical parameter name of the layer 3 connection object. Example: InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANPPPConnection.1. This parameter is OBSOLETED because it is within an OBSOLETED object.
- 1.0
DestinationAddress string(:256) R

Destination address of the WANConnectionDevice entry. One of:

  • PVC: VPI/VCI
  • SVC: ATM connection name
  • SVC: ATM address
The “PVC:” or “SVC:” prefix is part of the parameter value and MUST be followed by 0 or 1 space characters. For example, possible values for this parameter are “PVC:8/23” or “PVC: 0/35”. This parameter is OBSOLETED because it is within an OBSOLETED object.
- 1.0
LinkType string(:16) R
Link Type of the WANConnectionDevice entry. One of Link Types as described in WANDSLLinkConfig. This parameter is OBSOLETED because it is within an OBSOLETED object.
- 1.0
ConnectionType string(:16) R
Connection Type of the WANPPPConnection or WANIPConnection entry. One of PossibleConnectionTypes as described in WAN**Connection service.
This parameter is OBSOLETED because it is within an OBSOLETED object.
- 1.0
Name string(:32) R
User-readable name of the connection.
This parameter is OBSOLETED because it is within an OBSOLETED object.
- 1.0
InternetGatewayDevice.WANDevice.{i}.WANDSLDiagnostics. object R This object is to provide diagnostic information for a CPE with an ADSL2 or ADSL2+ modem WAN interface, but MAY also be used for ADSL. - 1.0
LoopDiagnosticsState string W

Indicates availability of diagnostic data. Enumeration of:

  • None (READONLY)
  • Requested
  • Complete (READONLY)
  • Error_Internal (READONLY)
  • Error_Other (READONLY) If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test, which brings down the DSL connection while the test is operating. When writing, the only allowed value is Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Complete (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Complete, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed, the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the corresponding reason in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object instance) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None.

Active Notification requests for this parameter MAY be denied.

- 1.0
ACTPSDds int R

Downstream actual power spectral density. Interpretation of the value is as defined in ITU-T Rec. G.997.1.

Note: See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
ACTPSDus int R

Upstream actual power spectral density. Interpretation of the value is as defined in ITU-T Rec. G.997.1.

Note: See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
ACTATPds int R

Downstream actual aggregate transmitter power. Interpretation of the value is as defined in ITU-T Rec. G.997.1.

Note: See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
ACTATPus int R

Upstream actual aggregate transmitter power. Interpretation of the value is as defined in ITU-T Rec. G.997.1.

Note: See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLINSCds int R

Downstream linear representation scale. Interpretation of the value is as defined in ITU-T Rec. G.997.1.

Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLINpsds int[](:61430) R

Comma-separated list (maximum number of characters 61430) of integers. Downstream linear channel characteristics per subcarrier group. Maximum number of complex pairs is 256 for G.992.3, and 512 for G.992.5. For G.993.2, the number of pairs will depend on the value of HLINGds but will not exceed 512. Interpretation of the value is as defined in ITU-T Rec. G.997.1. Note: HLIN is not applicable in PLOAM for G.992.1 or G.992.2. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to None.

Active Notification requests for this parameter MAY be denied.

- 1.0
QLNpsds int[](:61430) R

Comma-separated list (maximum number of characters 61430) of integers. Downstream quiet line noise per subcarrier group. Maximum number of elements is 256 for G.992.3, 512 for G.992.5. For G.993.2, the number of elements will depend on the value of QLNGds but will not exceed 512. Interpretation of the value is as defined in ITU-T Rec. G.997.1. Note: QLN is not applicable in PLOAM for G.992.1 or G.992.2. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to None.

Active Notification requests for this parameter MAY be denied.

- 1.0
SNRpsds int[](:61430) R

Comma-separated list (maximum number of characters 61430) of integers. Downstream SNR per subcarrier group. Maximum number of elements is 256 for G.992.3, 512 for G.992.5. For G.993.2, the number of elements will depend on the value of SNRGds but will not exceed 512. Interpretation of the value is as defined in ITU-T Rec. G.997.1. Interpretation of the value is as defined in ITU-T Rec. G.997.1. Note: SNRps is not applicable in PLOAM for G.992.1 or G.992.2. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to None.

Active Notification requests for this parameter MAY be denied.

- 1.0
BITSpsds int[](:61430) R

Comma-separated list (maximum number of characters 61430) of integers. Downstream bit allocation per subcarrier group. Maximum number of elements is 256 for G.992.3, 512 for G.992.5. Interpretation of the value is as defined in ITU-T Rec. G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
GAINSpsds int[](:61430) R

Comma-separated list (maximum number of characters 61430) of integers. Downstream gain allocation per subcarrier group. Maximum number of elements is 256 for G.992.3, 512 for G.992.5. Interpretation of the value is as defined in ITU-T Rec. G.997.1. This parameter is DEPRECATED.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLINSCus int R

Scaling used to represent the upstream linear channel characteristics. Interpretation of the value is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLINGds unsignedInt R

Number of sub-carriers per sub-carrier group in the downstream direction for HLINpsds. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLINGus unsignedInt R

Number of sub-carriers per sub-carrier group in the downstream direction for HLINpsus. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLOGGds unsignedInt R

Number of sub-carriers per sub-carrier group in the downstream direction for HLOGpsds. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLOGGus unsignedInt R

Number of sub-carriers per sub-carrier group in the upstream direction for HLOGpsus. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLOGpsds string[](:2559) R

Comma-separated list (maximum number of characters 2559) of strings. Downstream logarithmic channel characteristics per sub-carrier group. The maximum number of elements is 256 for G.992.3, and 512 for G.992.5. For G.993.2, the number of elements will depend on the value of HLOGGds but will not exceed 512. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to None. Note: HLOGpsds is measured during initialization and is not updated during Showtime.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLOGpsus string[](:2559) R

Comma-separated list (maximum number of characters 2559) of strings. Upstream logarithmic channel characteristics per sub-carrier group. The maximum number of elements is 64 for G.992.3 and G.992.5. For G.993.2, the number of elements will depend on the value of HLOGGus but will not exceed 512. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to None. Note: HLOGpsus is measured during initialization and is not updated during Showtime.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLOGMTds unsignedInt R

Indicates the number of symbols over which HLOGpsds was measured. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLOGMTus unsignedInt R

Indicates the number of symbols over which HLOGpsus was measured. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
LATNpbds string[](:24) R

Comma-separated list (maximum number of characters 24) of strings. Downstream line attenuation per usable band, as computed during initialization. Number of elements is dependent on the number of downstream bands but will exceed one only for G.993.2. Interpretation of LATNpbds is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
LATNpbus string[](:24) R

Comma-separated list (maximum number of characters 24) of strings. Upstream line attenuation per usable band, as computed during initialization. Number of elements is dependent on the number of upstream bands but will exceed one only for G.993.2. Interpretation of LATNpbus is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
SATNds string[](:24) R

Comma-separated list (maximum number of characters 24) of strings. Downstream signal attenuation per usable band, as computed during the L0 (i.e., Showtime) state. Number of elements is dependent on the number of downstream bands but will exceed one only for G.993.2. Interpretation of SATNds is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
SATNus string[](:24) R

Comma-separated list (maximum number of characters 24) of strings. Upstream signal attenuation per usable band, as computed during the L0 (i.e., Showtime) state. Number of elements is dependent on the number of downstream bands but will exceed one only for G.993.2. Interpretation of SATNus is as defined in ITU-T Rec. G.997.1. Note: See ITU-T Recommendation G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
HLINpsus string[](:61430) R

Comma-separated list (maximum number of characters 61430) of strings. Upstream linear channel characteristics per sub-carrier group. Maximum number of complex pairs is 64 for G.992.3, and G.992.5. For G.993.2, the number of pairs will depend on the value of HLINGus but will not exceed 512. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: HLIN is not applicable in PLOAM for G.992.1 or G.992.2. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to None.

Active Notification requests for this parameter MAY be denied.

- 1.0
QLNGds unsignedInt R

Number of sub-carriers per sub-carrier group in the downstream direction for QLNpsds. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
QLNGus unsignedInt R

Number of sub-carriers per sub-carrier group in the upstream direction for QLNpsus. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
QLNpsus string[](:61430) R

Comma-separated list (maximum number of characters 61430) of strings. Upstream quiet line noise per subcarrier group. The maximum number of elements is 64 for G.992.3, and G.992.5. For G.993.2, the number of elements will depend on the value of QLNGus but will not exceed 512. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: QLN is not applicable in PLOAM for G.992.1 or G.992.2. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to None.

Active Notification requests for this parameter MAY be denied.

- 1.0
QLNMTds unsignedInt R

Indicates the number of symbols over which QLNpsds was measured. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
QLNMTus unsignedInt R

Indicates the number of symbols over which QLNpsus was measured. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
SNRGds unsignedInt R

Number of sub-carriers per sub-carrier group in the downstream direction for SNRpsds. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
SNRGus unsignedInt R

Number of sub-carriers per sub-carrier group in the upstream direction for SNRpsus. Valid values are 1, 2, 4, and 8. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 1.

Active Notification requests for this parameter MAY be denied.

- 1.0
SNRpsus string[](:61430) R

Comma-separated list (maximum number of characters 61430) of strings. Upstream SNR per subcarrier group. The maximum number of elements is 64 for G.992.3, and G.992.5. For G.993.2, the number of elements will depend on the value of SNRGus but will not exceed 512. Interpretation of the values is as defined in ITU-T Rec. G.997.1. Note: SNRps is not applicable in PLOAM for G.992.1 or G.992.2. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to None.

Active Notification requests for this parameter MAY be denied.

- 1.0
SNRMTds unsignedInt R

Indicates the number of symbols over which SNRpsds was measured. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
SNRMTus unsignedInt R

Indicates the number of symbols over which SNRpsus was measured. Note: See ITU-T Recommendation G.997.1. For a multimode device operating in a mode in which this parameter does not apply, the value of this parameter SHOULD be set to 0.

Active Notification requests for this parameter MAY be denied.

- 1.0
BITSpsus string[](:61430) R

Comma-separated list (maximum number of characters 61430) of strings. Upstream bit allocation per subcarrier group. Maximum number of elements is 256 for G.992.3, 512 for G.992.5. Interpretation of the value is as defined in ITU-T Rec. G.997.1.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}. object(0:) W Each instance contains objects associated with a given WAN link. In the case of DSL, each instance corresponds to either a single ATM VC or a PTM Ethernet link. On creation of a WANConnectionDevice instance, there are initially no connection objects contained within. In the case of Ethernet (interface or link), only one WANConnectionDevice instance is supported. - 1.0
WANIPConnectionNumberOfEntries unsignedInt R Number of instances of WANIPConnection in this WANConnectionDevice. - 1.0
WANPPPConnectionNumberOfEntries unsignedInt R Number of instances of WANPPPConnection in this WANConnectionDevice. - 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANDSLLinkConfig. object(0:1) R

This object models the ATM layer properties specific to a single physical connection of a DSL modem used for Internet access on a CPE. This object is intended for a CPE with a DSL modem WAN interface, and is exclusive of any other WANLinkConfig* object within a given WANConnectionDevice instance.

This object is a member of a union, i.e., it is a member of a group of objects of which only one can exist at a given time.

- 1.0
Enable boolean W Enables or disables the link. On creation of a WANConnectionDevice, this object is disabled by default. false 1.0
LinkStatus string R

Status of the link.

Enumeration of:

  • Up
  • Down
  • Initializing
  • Unavailable
- 1.0
LinkType string W

Indicates the type of DSL connection and refers to the complete stack of protocol used for this connection. Enumeration of:

  • EoA (RFC 2684 [RFC2684] bridged Ethernet over ATM)
  • IPoA (RFC 2684 [RFC2684] routed IP over ATM)
  • PPPoA (RFC 2364 [RFC2634] PPP over ATM)
  • PPPoE (RFC 2516 [RFC2516] PPP over Ethernet on RFC 2684 [RFC2684] bridged Ethernet over ATM, DEPRECATED)
  • CIP (RFC 2225 [RFC2225] Classical IP over ATM)
  • Unconfigured The value {{enum: reference to deprecated enumeration InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANDSLLinkConfig.LinkType.PPPoE}} has always been DEPRECATED and EoA SHOULD be used instead (see [Annex B/TR-098a2]). The ACS MUST NOT set this parameter to {{enum: reference to deprecated enumeration InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANDSLLinkConfig.LinkType.PPPoE}} and the CPE MUST reject attempts to do so.
Unconfigured 1.0
AutoConfig boolean R Indicates if the CPE is currently using some auto configuration mechanisms for this connection. If this variable is true, all writable variables in this connection instance become read-only. Any attempt to change one of these variables SHOULD fail and an error SHOULD be returned. - 1.0
ModulationType string R

Indicates the type of DSL modulation used on the interface associated with this connection (duplication from WANDSLInterfaceConfig).

Enumeration of:

  • ADSL_G.dmt
  • ADSL_G.lite
  • ADSL_G.dmt.bis
  • ADSL_re-adsl
  • ADSL_2plus
  • ADLS_four
  • ADSL_ANSI_T1.413
  • G.shdsl
  • IDSL
  • HDSL
  • SDSL
  • VDSL
- 1.0
DestinationAddress string(:256) W

Destination address of this link. One of:

  • PVC: VPI/VCI
  • SVC: ATM connection name
  • SVC: ATM address

The “PVC:” or “SVC:” prefix is part of the parameter value and MUST be followed by 0 or 1 space characters. For example, possible values for this parameter are “PVC:8/23” or “PVC: 0/35”.

- 1.0
ATMEncapsulation string W

Identifies the connection encapsulation that will be used.

Enumeration of:

  • LLC
  • VCMUX
- 1.0
FCSPreserved boolean W This flag tells if a checksum SHOULD be added in the ATM payload. It does not refer to the checksum of one of the ATM cells or AALX packets. In case of LLC or VCMUX encapsulation, this ATM checksum is the FCS field described in RFC 2684 [RFC2684]. It is only applicable in the upstream direction. - 1.0
VCSearchList string[](:256) W

Comma-separated list (maximum number of characters 256) of strings. Ordered list of VPI/VCI pairs to search if a link using the DestinationAddress cannot be established. In the form:

VPI1/VCI1, VPI2/VCI2, … Example:
0/35, 8/35, 1/35
- 1.0
ATMAAL string R

Describes the ATM Adaptation Layer (AAL) currently in use on the PVC.

Enumeration of:

  • AAL1
  • AAL2
  • AAL3
  • AAL4
  • AAL5
- 1.0
ATMTransmittedBlocks unsignedInt R

The current count of successfully transmitted cells.

Active Notification requests for this parameter MAY be denied.

- 1.0
ATMReceivedBlocks unsignedInt R

The current count of successfully received cells.

Active Notification requests for this parameter MAY be denied.

- 1.0
ATMQoS string W

Describes the ATM Quality Of Service (QoS) being used on the VC.

Enumeration of:

  • UBR
  • CBR
  • GFR
  • VBR-nrt
  • VBR-rt
  • UBR+
  • ABR
- 1.0
ATMPeakCellRate unsignedInt W Specifies the upstream peak cell rate in cells per second. - 1.0
ATMMaximumBurstSize unsignedInt W Specifies the upstream maximum burst size in cells. - 1.0
ATMSustainableCellRate unsignedInt W Specifies the upstream sustainable cell rate, in cells per second, used for traffic shaping. - 1.0
AAL5CRCErrors unsignedInt R

Count of the AAL5 layer cyclic redundancy check errors.

This parameter is DEPRECATED because it overlaps with the ATMCRCErrors parameter. If present, it MUST have the same value as the ATMCRCErrors parameter if AAL5 is in use, or 0 if AAL5 is not in use.

Active Notification requests for this parameter MAY be denied.

- 1.0
ATMCRCErrors unsignedInt R

Count of the ATM layer cyclic redundancy check (CRC) errors. This refers to CRC errors at the ATM adaptation layer (AAL). The AAL in use is indicated by the ATMAAL parameter. The value of the ATMCRCErrors parameter MUST be 0 for AAL types that have no CRCs.

Active Notification requests for this parameter MAY be denied.

- 1.0
ATMHECErrors unsignedInt R

Count of the number of Header Error Check related errors at the ATM layer.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANATMF5LoopbackDiagnostics. object R This object is provides access to an ATM-layer F5 OAM loopback test. - 1.0
DiagnosticsState string W

Indicates availability of diagnostic data. Enumeration of:

  • None (READONLY)
  • Requested
  • Complete (READONLY)
  • Error_Internal (READONLY)
  • Error_Other (READONLY) If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Complete (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Complete, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code 8 DIAGNOSTICS COMPLETE in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object instance) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None. Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None. While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None. While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

Active Notification requests for this parameter MAY be denied.

None 1.0
NumberOfRepetitions unsignedInt(1:) W Number of repetitions of the ping test to perform before reporting the results. 1 1.0
Timeout unsignedInt(1:) W Timeout in milliseconds for the ping test. - 1.0
SuccessCount unsignedInt R

Result parameter indicating the number of successful pings (those in which a successful response was received prior to the timeout) in the most recent ping test.

Active Notification requests for this parameter MAY be denied.

0 1.0
FailureCount unsignedInt R

Result parameter indicating the number of failed pings in the most recent ping test.

Active Notification requests for this parameter MAY be denied.

0 1.0
AverageResponseTime unsignedInt R

Result parameter indicating the average response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero.

Active Notification requests for this parameter MAY be denied.

0 1.0
MinimumResponseTime unsignedInt R

Result parameter indicating the minimum response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero.

Active Notification requests for this parameter MAY be denied.

0 1.0
MaximumResponseTime unsignedInt R

Result parameter indicating the maximum response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero.

Active Notification requests for this parameter MAY be denied.

0 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANPTMLinkConfig. object(0:1) R

This object models the PTM layer properties specific to a layer 2 interface of a DSL modem used for Internet access on a CPE. This object is intended for a CPE with a DSL modem WAN interface, and is exclusive of any other WANLinkConfig* object within a given WANConnectionDevice instance. The PTM Link Layer object exists when the WANDSLInterfaceConfig LinkEncapsulationSupported parameter includes any of:

  • G.992.3_Annex_K_PTM
  • G.993.2_Annex_K_PTM
  • G.994.1

This object is a member of a union, i.e., it is a member of a group of objects of which only one can exist at a given time.

- 1.0
Enable boolean W Enables or disables the link. On creation of a WANConnectionDevice, this object is disabled by default. false 1.0
LinkStatus string R

Status of the link.

Enumeration of:

  • Up
  • Down
  • Initializing
  • Unavailable
- 1.0
MACAddress string(:17) R [MACAddress] The physical address of the interface. - 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANPTMLinkConfig.Stats. object R This object represents the statistics collected and returned over a PTM link. - 1.0
BytesSent unsignedInt R

The total number of bytes transmitted out of the interface, including framing characters. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
BytesReceived unsignedInt R

The total number of bytes received on the interface, including framing characters. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
FramesSent unsignedInt R

The total number of packets (frames) transmitted out of the interface. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
FramesReceived unsignedInt R

The total number of packets (frames) which were received on this interface. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
OOSNearEnd boolean R Indication that the CPE has detected the link is Out of Synchronization since the CPE rebooted or the interface was last enabled. - 1.0
OOSFarEnd boolean R Indication that the remote device has detected the link is Out of Synchronization since the CPE rebooted or the interface was last enabled. - 1.0
ErrorsSent unsignedInt R

The total number of outbound packets that could not be transmitted because of errors. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
ErrorsReceived unsignedInt R

The total number of inbound packets that contained errors preventing them from being deliverable. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
UnicastPacketsSent unsignedInt R

The total number of packets requested for transmission which were not addressed to a multicast or broadcast address, including those that were discarded or not sent. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
UnicastPacketsReceived unsignedInt R

The total number of received packets which were not addressed to a multicast or broadcast address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
DiscardPacketsSent unsignedInt R

The total number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
DiscardPacketsReceived unsignedInt R

The total number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable. One possible reason for discarding such a packet could be to free up buffer space. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
MulticastPacketsSent unsignedInt R

The total number of packets requested for transmission which were addressed to a multicast address, including those that were discarded or not sent. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
MulticastPacketsReceived unsignedInt R

The total number of received packets which were addressed to a multicast address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
BroadcastPacketsSent unsignedInt R

The total number of packets requested for transmission which were addressed to a broadcast address, including those that were discarded or not sent. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
BroadcastPacketsReceived unsignedInt R

The total number of received packets which were addressed to a broadcast address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
UnknownProtoPacketsReceived unsignedInt R

The total number of packets received via the interface which were discarded because of an unknown or unsupported protocol. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANEthernetLinkConfig. object(0:1) R

This object models the Ethernet link layer properties specific to a single physical connection used for Internet access on a CPE. This object is intended for a CPE with an Ethernet WAN interface, and is exclusive of any other WANLinkConfig* object within a given WANConnectionDevice instance. Note that this object is not related to the Ethernet protocol layer sometimes used in associated with a DSL connection.

This object is a member of a union, i.e., it is a member of a group of objects of which only one can exist at a given time.

- 1.0
EthernetLinkStatus string R

Status of the Ethernet link.

Enumeration of:

  • Up
  • Down
  • Unavailable
- 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANPOTSLinkConfig. object(0:1) R

This object models the POTS link layer properties specific to a single physical connection used for Internet access on a CPE. This object is intended for a CPE with a POTS WAN interface, and is exclusive of any other WANLinkConfig* object within a given WANConnectionDevice instance.

This object is a member of a union, i.e., it is a member of a group of objects of which only one can exist at a given time.

- 1.0
Enable boolean W Enables or disables the link. On creation of a WANConnectionDevice, this object is disabled by default. false 1.0
LinkStatus string R

Status of the link.

Enumeration of:

  • Up
  • Down
  • Dialing
  • Connecting
  • Unavailable
- 1.0
ISPPhoneNumber string(:64) W Specifies a list of strings separated by semicolon (;), each string representing a phone number to connect to a particular ISP. The digits of the phone number follow the semantics of the ITU-T E.164 specification. Delimiters such as brackets or hyphens between the digits of a phone number are to be ignored by the CPE. <Empty> 1.0
ISPInfo string(:64) W Information identifying the Internet Service Provider. The format of the string is vendor specific. <Empty> 1.0
LinkType string W

This variable indicates the type of POTS link used for the dialup connection.

Enumeration of:

  • PPP_Dialup
PPP_Dialup 1.0
NumberOfRetries unsignedInt W The number of times the CPE SHOULD attempt an Internet connection setup before returning error. - 1.0
DelayBetweenRetries unsignedInt W The number of seconds the CPE SHOULD wait between attempts to setup an Internet connection. - 1.0
Fclass string[] R

Comma-separated list of strings. Specifies capabilities of the POTS modem - i.e., if it handles data (0), fax (1,2,2.0), voice (8), DSVD (80).

Each list item is an enumeration of:

  • 0
  • 1
  • 2
  • 2.0
  • 8
  • 80
- 1.0
DataModulationSupported string R

The modulation standard currently being used for data.

Enumeration of:

  • V92
  • V90
  • V34
  • V32bis
  • V32
- 1.0
DataProtocol string R

The protocol standard currently being used for data transfers.

Enumeration of:

  • V42_LAPM
  • V42_MNP4
  • V14
  • V80
- 1.0
DataCompression string R

The compression technology implemented on the modem.

Enumeration of:

  • V42bis
  • MNP5
- 1.0
PlusVTRCommandSupported boolean R Capability for full duplex operation with data and voice. - 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}. object(0:) W

This object enables configuration of IP connections on the WAN interface of a CPE.

If the Layer2Bridging object is implemented, the view that it provides of the CPE’s underlying bridging configuration MUST be consistent with the view provided by any LANDevice and WAN**Connection objects. The implications of this are explained in [Annex A.6/TR-098a2].

At most one enabled entry in this table can exist with a given value for ExternalIPAddress.

- 1.0
Enable boolean W Enables or disables the connection instance. On creation of a WANIPConnection instance, it is initially disabled. false 1.0
Reset boolean W When set to true, the device MUST tear down the existing IP connection represented by this object and establish a new one. The device MUST initiate the reset after completion of the current CWMP session. The device MAY delay resetting the connection in order to avoid interruption of a user service such as an ongoing voice call. When read, this parameter always returns false. false 1.0
ConnectionStatus string R

Current status of the connection.

Enumeration of:

  • Unconfigured
  • Connecting
  • Connected
  • PendingDisconnect
  • Disconneting (DEPRECATED)
  • Disconnecting
  • Disconnected The value {{enum: reference to deprecated enumeration InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.ConnectionStatus.Disconneting}} is DEPRECATED because it is a typo. The ACS MUST treat {{enum: reference to deprecated enumeration InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.ConnectionStatus.Disconneting}} and Disconnecting the same.
- 1.0
PossibleConnectionTypes string[] R

Comma-separated list of strings. Types of connections possible for this connection instance.

Each list item is an enumeration of:

  • Unconfigured
  • IP_Routed
  • IP_Bridged
- 1.0
ConnectionType string W

Specifies the connection type of the connection instance.

Enumeration of:

  • Unconfigured
  • IP_Routed
  • IP_Bridged
- 1.0
Name string(:256) W User-readable name of this connection. - 1.0
Uptime unsignedInt R

The time in seconds that this connection has been up.

Active Notification requests for this parameter MAY be denied.

- 1.0
LastConnectionError string R

The cause of failure for the last connection setup attempt.

Enumeration of:

  • ERROR_NONE
  • ERROR_COMMAND_ABORTED
  • ERROR_NOT_ENABLED_FOR_INTERNET
  • ERROR_USER_DISCONNECT
  • ERROR_ISP_DISCONNECT
  • ERROR_IDLE_DISCONNECT
  • ERROR_FORCED_DISCONNECT
  • ERROR_NO_CARRIER
  • ERROR_IP_CONFIGURATION
  • ERROR_UNKNOWN
ERROR_NONE 1.0
AutoDisconnectTime unsignedInt W The time in seconds since the establishment of the connection after which connection termination is automatically initiated by the CPE. This occurs irrespective of whether the connection is being used or not. A value of 0 (zero) indicates that the connection is not to be shut down automatically. - 1.0
IdleDisconnectTime unsignedInt W The time in seconds that if the connection remains idle, the CPE automatically terminates the connection. A value of 0 (zero) indicates that the connection is not to be shut down automatically. - 1.0
WarnDisconnectDelay unsignedInt W Time in seconds the Status remains in the pending disconnect state before transitioning to disconnecting state to drop the connection. - 1.0
RSIPAvailable boolean R Indicates if Realm-specific IP (RSIP) is available as a feature on the CPE. - 1.0
NATEnabled boolean W Indicates if Network Address Translation (NAT) is enabled for this connection. - 1.0
AddressingType string W

The method used to assign an address to the WAN side interface of the CPE for this connection.

Enumeration of:

  • DHCP
  • Static
- 1.0
ExternalIPAddress string(:45) W [IPAddress] This is the external IP address used by NAT for this connection. This parameter is configurable only if the AddressingType is Static. - 1.0
SubnetMask string(:45) W [IPAddress] Subnet mask of the WAN interface. This parameter is configurable only if the AddressingType is Static. - 1.0
DefaultGateway string W The IP address of the default gateway for this connection. This parameter is configurable only if the AddressingType is Static. - 1.0
DNSEnabled boolean W Whether or not the device SHOULD attempt to query a DNS server across this connection. true 1.0
DNSOverrideAllowed boolean W Whether or not a manually set, non-empty DNS address can be overridden by a DNS entry received from the WAN. false 1.0
DNSServers string(:45)[](:64) W [IPAddress] Comma-separated list (maximum number of characters 64) of IP Addresses. DNS server IP addresses for this connection. Support for more than three DNS Servers is OPTIONAL. - 1.0
MaxMTUSize unsignedInt(1:1540) W The maximum allowed size of an Ethernet frame from LAN-side devices. - 1.0
MACAddress string(:17) W [MACAddress] The physical address of the WANIPConnection if applicable. Configurable only if MACAddressOverride is present and true. - 1.0
MACAddressOverride boolean W Whether the value of MACAddress parameter can be overridden. If false, the CPE’s default value is used (or restored if it had previously been overridden). - 1.0
ConnectionTrigger string W

Trigger used to establish the IP connection.

Enumeration of:

  • OnDemand
  • AlwaysOn
  • Manual The above values are defined as follows:
  • OnDemand: If this IP connection is disconnected for any reason, it is to remain disconnected until the CPE has one or more packets to communicate over this connection, at which time the CPE automatically attempts to reestablish the connection.
  • AlwaysOn: If this IP connection is disconnected for any reason, the CPE automatically attempts to reestablish the connection (and continues to attempt to reestablish the connection as long it remains disconnected).
  • Manual: If this IP connection is disconnected for any reason, it is to remain disconnected until the user of the CPE explicitly instructs the CPE to reestablish the connection. Note that the reason for an IP connection becoming disconnected to begin with might be either external to the CPE, such as non-renewal of a DHCP lease or momentary disconnection of the physical interface, or internal to the CPE, such as use of the IdleDisconnectTime and/or AutoDisconnectTime parameters in this object. Note also that the means by which a CPE would keep an IP connection disconnected (while waiting for the designated trigger) if it is otherwise physically connected and has an IP address is a local matter specific to the implementation of the CPE.
OnDemand 1.0
RouteProtocolRx string W

Defines the Rx protocol to be used.

Enumeration of:

  • Off
  • RIPv1 (OPTIONAL)
  • RIPv2 (OPTIONAL)
  • OSPF (OPTIONAL)
Off 1.0
PortMappingNumberOfEntries unsignedInt R Total number of port mapping entries. - 1.0
ShapingRate int(-1:) W Rate to shape this connection’s egress traffic to. For leaky bucket (constant rate shaping), this is the constant rate. For token bucket (variable rate shaping), this is the average rate. If <= 100, in percent of the rate of the highest rate-constrained layer over which the packet will travel on egress. If > 100, in bits per second. A value of -1 indicates no shaping. For example, for packets destined for a WAN DSL interface, if the ATM layer is rate-constrained, then the rate is calculated relative to this rate. Otherwise, the rate is calculated relative to the physical-layer DSL rate. -1 1.0
ShapingBurstSize unsignedInt W Burst size in bytes. For both leaky bucket (constant rate shaping) and token bucket (variable rate shaping) this is the bucket size and is therefore the maximum burst size. 0 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.DHCPClient. object R This object contains DHCP client configuration parameters. - 1.0
SentDHCPOptionNumberOfEntries unsignedInt R The number of entries in the SentDHCPOption table. - 1.0
ReqDHCPOptionNumberOfEntries unsignedInt R The number of entries in the ReqDHCPOption table. - 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.DHCPClient.SentDHCPOption.{i}. object(0:) W

Each instance of this object represents a DHCP option that MUST, if enabled, be sent in DHCP client requests. All sent DHCP options MUST be listed.

At most one enabled entry in this table can exist with a given value for Tag.

- 1.0
Enable boolean W Enables or disables this SentDHCPOption table entry. false 1.0
Tag unsignedInt(1:254) W Option tag as defined in RFC 2132 [RFC2132]. - 1.0
Value base64(0:255) W Base64 encoded option value. <Empty> 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.DHCPClient.ReqDHCPOption.{i}. object(0:) W

Each instance of this object represents a DHCP option that MUST, if enabled, be requested in DHCP client requests. All requested DHCP options MUST be listed.

At most one enabled entry in this table can exist with a given value for Tag.

- 1.0
Enable boolean W Enables or disables this ReqDHCPOption table entry. false 1.0
Order unsignedInt(1:) W Position of the option in the DHCP client request. A value of 1 indicates the first entry. When this value is modified, if the value matches that of an existing entry, the Order value for the existing entry and all lower Order entries is incremented to ensure uniqueness of this value. A deletion causes Order values to be compacted. When a value is changed, incrementing occurs before compaction. The value on creation of a ReqDHCPOption table entry MUST be one greater than the largest current value. - 1.0
Tag unsignedInt(1:254) W Option tag as defined in RFC 2132 [RFC2132]. - 1.0
Value base64(0:255) R Base64 encoded most recently received DHCP option value. If no option value has been received, then the value MUST represent an empty string. Received DHCP option values MAY, but need not, persist across CPE reboots. <Empty> 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.PortMapping.{i}. object(0:) W

Port mapping table. This table MUST contain all NAT port mappings associated with this connection, including static and dynamic port mappings programmatically created via local control protocol, such as UPnP. This table MUST NOT contain dynamic NAT binding entries associated with the normal operation of NAT. At most one entry in an instance of this table can exist with all of the same values for RemoteHost, ExternalPort, and PortMappingProtocol. If the ACS attempts to set the parameters of an existing entry such that this requirement would be violated, the CPE MUST reject the request. In this case, the SetParameterValues response MUST include a SetParameterValuesFault element for each parameter in the corresponding request whose modification would have resulted in such a violation. On creation of a new table entry, the CPE MUST choose default values for ExternalPort and PortMappingProtocol such that the new entry does not conflict with any existing entry.

At most one enabled entry in this table can exist with the same values for all of RemoteHost, ExternalPort and PortMappingProtocol.

- 1.0
PortMappingEnabled boolean W Enables or disables the port mapping instance. On creation, an entry is disabled by default. false 1.0
PortMappingLeaseDuration unsignedInt W

Determines the time to live, in seconds, of a port-mapping lease, where “time to live” means the number of seconds before the port mapping expires. A value of 0 means the port mapping is static. Support for dynamic (non-static) port mappings is OPTIONAL. That is, the only value for PortMappingLeaseDuration that MUST be supported is 0. For a dynamic (non-static) port mapping, when this parameter is read, the value represents the time remaining on the port-mapping lease. That is, for a dynamic port mapping, the value counts down toward 0. When a dynamic port-mapping lease expires, the CPE MUST automatically terminate that port mapping, and MUST automatically delete the corresponding PortMapping table entry.

Active Notification requests for this parameter MAY be denied.

- 1.0
RemoteHost string W This parameter is the IP address of the source of inbound packets. An empty string indicates a “wildcard” (this will be a wildcard in most cases). CPE are REQUIRED only to support wildcards. When RemoteHost is a wildcard, all traffic sent to the ExternalPort on the WAN interface of the gateway is forwarded to the InternalClient on the InternalPort. When RemoteHost is specified as one external IP address, the NAT will only forward inbound packets from this RemoteHost to the InternalClient, all other packets will be dropped. If a CPE supports non-wildcard values for RemoteHost, it MAY additionally support the ability to have more than one port mapping with the same ExternalPort and PortMappingProtocol, but with differing values of RemoteHost. When wildcard values are used for RemoteHost and/or ExternalPort, the following precedence order applies (with the highest precedence listed first):
  1. Explicit RemoteHost, explicit ExternalPort
  2. Explicit RemoteHost, wildcard ExternalPort
  3. Wildcard RemoteHost, explicit ExternalPort
  4. Wildcard RemoteHost, wildcard ExternalPort If an incoming packet matches the criteria associated with more than one entry in this table, the CPE MUST apply the port mapping associated with the highest precedence entry. At most one entry in this table can exist with all of the same values for RemoteHost, ExternalPort, and PortMappingProtocol.
<Empty> 1.0
ExternalPort unsignedInt W The external port (or the first port of a range of external ports) that the NAT gateway would listen on for connection requests to a corresponding InternalPort. Inbound packets to this external port on the WAN interface SHOULD be forwarded to InternalClient on the InternalPort. A value of zero (0) represents a “wildcard”. If this value is a wildcard, connection requests on all external ports (that are not otherwise mapped) will be forwarded to InternalClient. In the wildcard case, the value(s) of InternalPort on InternalClient are ignored. When wildcard values are used for RemoteHost and/or ExternalPort, the following precedence order applies (with the highest precedence listed first):
  1. Explicit RemoteHost, explicit ExternalPort
  2. Explicit RemoteHost, wildcard ExternalPort
  3. Wildcard RemoteHost, explicit ExternalPort
  4. Wildcard RemoteHost, wildcard ExternalPort If an incoming packet matches the criteria associated with more than one entry in this table, the CPE MUST apply the port mapping associated with the highest precedence entry. At most one entry in this table can exist with all of the same values for RemoteHost, ExternalPort, and PortMappingProtocol.
- 1.0
InternalPort unsignedInt W The port on InternalClient that the gateway SHOULD forward connection requests to. A value of zero (0) is not allowed. - 1.0
PortMappingProtocol string W

The protocol of the port mapping.

Enumeration of:

  • TCP
  • UDP At most one entry in this table can exist with all of the same values for RemoteHost, ExternalPort, and PortMappingProtocol.
- 1.0
InternalClient string(:256) W The IP address or DNS host name of an internal client (on the LAN). Support for an IP address is mandatory. If InternalClient is specified as an IP address and the LAN device’s IP address subsequently changes, the port mapping MUST remain associated with the original IP address. Support for DNS host names is OPTIONAL. If InternalClient is specified as a DNS host name and the LAN device’s IP address subsequently changes, the port mapping MUST remain associated with this LAN device. In this case, it is the responsibility of the CPE to maintain the name-to-address mapping in the event of IP address changes. This can be accomplished, for example, by assigning the DNS host name via use of DHCP option 12 (Host Name) or option 81 (FQDN). Note that the ACS can learn the host name associated with a given LAN device via the Hosts table (InternetGatewayDevice.LANDevice.{i}.Hosts). Read access to this parameter MUST always return the exact value that was last set by the ACS. For example, if the internal client is set to a DNS host name, it MUST read back as a DNS host name and not as an IP address. An empty string indicates an unconfigured InternalClient. If this parameter is unconfigured, this port mapping MUST NOT be operational. It MUST be possible to set the InternalClient to the broadcast IP address 255.255.255.255 for UDP mappings. This is to enable multiple NAT clients to use the same well-known port simultaneously. <Empty> 1.0
PortMappingDescription string(:256) W User-readable description of this port mapping. <Empty> 1.0
ExternalPortEndRange unsignedInt W Indicates the last port of the external port range that starts with ExternalPort. If an external port range is specified, then the behavior described for ExternalPort applies to all ports within the range. A value of zero (0) indicates that no external port range is specified, i.e. that the range consists only of ExternalPort. If ExternalPort is zero (wildcard), the value of this parameter MUST be ignored. If specified, the value of this parameter MUST be greater than or equal to the value of ExternalPort. 0 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.Stats. object R This object contains statistics for all connections within the same WANConnectionDevice that share a common MAC address. The contents of this object SHOULD be identical for each such connection. This object is intended only for WANConnectionDevices that can support an Ethernet-layer on this interface (e.g., PPPoE, IPoE). - 1.0
EthernetBytesSent unsignedInt R

The total number of bytes transmitted, including framing characters, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetBytesReceived unsignedInt R

The total number of bytes received, including framing characters, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetPacketsSent unsignedInt R

The total number of packets transmitted over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetPacketsReceived unsignedInt R

The total number of packets which were received over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetErrorsSent unsignedInt R

The total number of outbound packets that could not be transmitted because of errors, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetErrorsReceived unsignedInt R

The total number of inbound packets that contained errors preventing them from being deliverable, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetUnicastPacketsSent unsignedInt R

The total number of packets requested for transmission which were not addressed to a multicast or broadcast address, including those that were discarded or not sent, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetUnicastPacketsReceived unsignedInt R

The total number of received packets which were not addressed to a multicast or broadcast address, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetDiscardPacketsSent unsignedInt R

The total number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted, over all connections within the same WANConnectionDevice that share a common MAC address. One possible reason for discarding such a packet could be to free up buffer space. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetDiscardPacketsReceived unsignedInt R

The total number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable, over all connections within the same WANConnectionDevice that share a common MAC address. One possible reason for discarding such a packet could be to free up buffer space. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetMulticastPacketsSent unsignedInt R

The total number of packets requested for transmission, including those that were discarded or not sent, which were addressed to a multicast address, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetMulticastPacketsReceived unsignedInt R

The total number of received packets which were addressed to a multicast address, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetBroadcastPacketsSent unsignedInt R

The total number of packets requested for transmission, including those that were discarded or not sent, which were addressed to a broadcast address, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetBroadcastPacketsReceived unsignedInt R

The total number of received packets which were addressed to a broadcast address, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetUnknownProtoPacketsReceived unsignedInt R

The total number of packets which were discarded because of an unknown or unsupported protocol, received over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANPPPConnection.{i}. object(0:) W

This object enables configuration of PPP connections on the WAN interface of a CPE.

If the Layer2Bridging object is implemented, the view that it provides of the CPE’s underlying bridging configuration MUST be consistent with the view provided by any LANDevice and WAN**Connection objects. The implications of this are explained in [Annex A.6/TR-098a2].

At most one enabled entry in this table can exist with a given value for ExternalIPAddress.

- 1.0
Enable boolean W Enables or disables the connection instance. On creation of a WANPPPConnection instance, it is initially disabled. false 1.0
Reset boolean W When set to true, the device MUST tear down the existing PPP connection represented by this object and establish a new one. The device MUST initiate the reset after completion of the current CWMP session. The device MAY delay resetting the connection in order to avoid interruption of a user service such as an ongoing voice call. When read, this parameter always returns false. false 1.0
ConnectionStatus string R

Current status of the connection.

Enumeration of:

  • Unconfigured
  • Connecting
  • Authenticating
  • Connected
  • PendingDisconnect
  • Disconnecting
  • Disconnected
- 1.0
PossibleConnectionTypes string[] R

Comma-separated list of strings. Types of connections possible for this connection instance.

Each list item is an enumeration of:

  • Unconfigured
  • IP_Routed
  • DHCP_Spoofed
  • PPPoE_Bridged
  • PPPoE_Relay
  • PPTP_Relay
  • L2TP_Relay
- 1.0
ConnectionType string W

Specifies the connection type of the connection instance.

Enumeration of:

  • Unconfigured
  • IP_Routed
  • DHCP_Spoofed
  • PPPoE_Bridged
  • PPPoE_Relay
  • PPTP_Relay
  • L2TP_Relay
- 1.0
PPPoESessionID unsignedInt(1:) R Represents the PPPoE Session ID. - 1.0
Name string(:256) W User-readable name of this connection. - 1.0
Uptime unsignedInt R

The time in seconds that this connection has been up.

Active Notification requests for this parameter MAY be denied.

- 1.0
LastConnectionError string R

The cause of failure for the last connection setup attempt.

Enumeration of:

  • ERROR_NONE
  • ERROR_ISP_TIME_OUT
  • ERROR_COMMAND_ABORTED
  • ERROR_NOT_ENABLED_FOR_INTERNET
  • ERROR_BAD_PHONE_NUMBER
  • ERROR_USER_DISCONNECT
  • ERROR_ISP_DISCONNECT
  • ERROR_IDLE_DISCONNECT
  • ERROR_FORCED_DISCONNECT
  • ERROR_SERVER_OUT_OF_RESOURCES
  • ERROR_RESTRICTED_LOGON_HOURS
  • ERROR_ACCOUNT_DISABLED
  • ERROR_ACCOUNT_EXPIRED
  • ERROR_PASSWORD_EXPIRED
  • ERROR_AUTHENTICATION_FAILURE
  • ERROR_NO_DIALTONE
  • ERROR_NO_CARRIER
  • ERROR_NO_ANSWER
  • ERROR_LINE_BUSY
  • ERROR_UNSUPPORTED_BITSPERSECOND
  • ERROR_TOO_MANY_LINE_ERRORS
  • ERROR_IP_CONFIGURATION
  • ERROR_UNKNOWN
ERROR_NONE 1.0
AutoDisconnectTime unsignedInt W The time in seconds since the establishment of the connection after which connection termination is automatically initiated by the CPE. This occurs irrespective of whether the connection is being used or not. A value of 0 (zero) indicates that the connection is not to be shut down automatically. - 1.0
IdleDisconnectTime unsignedInt W The time in seconds that if the connection remains idle, the CPE automatically terminates the connection. A value of 0 (zero) indicates that the connection is not to be shut down automatically. - 1.0
WarnDisconnectDelay unsignedInt W Time in seconds the Status remains in the pending disconnect state before transitioning to disconnecting state to drop the connection. - 1.0
RSIPAvailable boolean R Indicates if Realm-specific IP (RSIP) is available as a feature on the CPE. - 1.0
NATEnabled boolean W Indicates if Network Address Translation (NAT) is enabled for this connection. - 1.0
Username string(:64) W Username to be used for authentication. <Empty> 1.0
Password string(:64) W

Password to be usef for authentication.

When read, this parameter returns an empty string, regardless of the actual value.

<Empty> 1.0
PPPEncryptionProtocol string R

Describes the PPP encryption protocol used between the WAN device and the ISP POP.

Enumeration of:

  • None
  • MPPE
- 1.0
PPPCompressionProtocol string R

Describes the PPP compression protocol used between the WAN device and the ISP POP.

Enumeration of:

  • None
  • Van Jacobsen
  • STAC LZS
- 1.0
PPPAuthenticationProtocol string R

Describes the PPP authentication protocol used between the WAN device and the ISP POP.

Enumeration of:

  • PAP
  • CHAP
  • MS-CHAP
- 1.0
ExternalIPAddress string(:45) R [IPAddress] This is the external IP address used by NAT for this connection. - 1.0
RemoteIPAddress string(:45) R [IPAddress] The remote IP address for this connection. - 1.0
MaxMRUSize unsignedInt(1:1540) W The maximum allowed size of frames sent from the remote peer. - 1.0
CurrentMRUSize unsignedInt(1:1540) R

The current MRU in use over this connection.

Active Notification requests for this parameter MAY be denied.

- 1.0
DNSEnabled boolean W Whether or not the device SHOULD attempt to query a DNS server across this connection. true 1.0
DNSOverrideAllowed boolean W Whether or not a manually set, non-empty DNS address can be overridden by a DNS entry received from the WAN. false 1.0
DNSServers string(:45)[](:64) W [IPAddress] Comma-separated list (maximum number of characters 64) of IP Addresses. DNS server IP addresses for this connection. Support for more than three DNS Servers is OPTIONAL. - 1.0
MACAddress string(:17) W

[MACAddress] The physical address of the WANPPPConnection if applicable. Configurable only if MACAddressOverride is present and true.

If TransportType is PPPoA, the value of this parameter is irrelevant and MUST be an empty string.

- 1.0
MACAddressOverride boolean W

Whether the value of MACAddress parameter can be overridden. If false, the CPE’s default value is used (or restored if it had previously been overridden).

If TransportType is PPPoA, the value of this parameter is irrelevant and MUST be false.

- 1.0
TransportType string R

PPP transport type of the connection.

Enumeration of:

  • PPPoA
  • PPPoE
  • L2TP (for future use)
  • PPTP (for future use)
- 1.0
PPPoEACName string(:256) W PPPoE Access Concentrator. <Empty> 1.0
PPPoEServiceName string(:256) W PPPoE Service Name. <Empty> 1.0
ConnectionTrigger string W

Trigger used to establish the PPP connection.

Enumeration of:

  • OnDemand
  • AlwaysOn
  • Manual The above values are defined as follows:
  • OnDemand: If this PPP connection is disconnected for any reason, it is to remain disconnected until the CPE has one or more packets to communicate over this connection, at which time the CPE automatically attempts to reestablish the connection.
  • AlwaysOn: If this PPP connection is disconnected for any reason, the CPE automatically attempts to reestablish the connection (and continues to attempt to reestablish the connection as long it remains disconnected).
  • Manual: If this PPP connection is disconnected for any reason, it is to remain disconnected until the user of the CPE explicitly instructs the CPE to reestablish the connection. Note that the reason for a PPP connection becoming disconnected to begin with might be either external to the CPE, such as termination by the BRAS or momentary disconnection of the physical interface, or internal to the CPE, such as use of the IdleDisconnectTime and/or AutoDisconnectTime parameters in this object.
OnDemand 1.0
RouteProtocolRx string W

Defines the Rx protocol to be used.

Enumeration of:

  • Off
  • RIPv1 (OPTIONAL)
  • RIPv2 (OPTIONAL)
  • OSPF (OPTIONAL)
Off 1.0
PPPLCPEcho unsignedInt R PPP LCP Echo period in seconds. - 1.0
PPPLCPEchoRetry unsignedInt R Number of PPP LCP Echo retries within an echo period. - 1.0
PortMappingNumberOfEntries unsignedInt R Total number of port mapping entries. - 1.0
ShapingRate int(-1:) W Rate to shape this connection’s egress traffic to. For leaky bucket (constant rate shaping), this is the constant rate. For token bucket (variable rate shaping), this is the average rate. If <= 100, in percent of the rate of the highest rate-constrained layer over which the packet will travel on egress. If > 100, in bits per second. A value of -1 indicates no shaping. For example, for packets destined for a WAN DSL interface, if the ATM layer is rate-constrained, then the rate is calculated relative to this rate. Otherwise, the rate is calculated relative to the physical-layer DSL rate. -1 1.0
ShapingBurstSize unsignedInt W Burst size in bytes. For both leaky bucket (constant rate shaping) and token bucket (variable rate shaping) this is the bucket size and is therefore the maximum burst size. 0 1.0
DefaultGateway string R Represents the IP Address of the remote end Default Gateway established through PPPoE. - 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANPPPConnection.{i}.PortMapping.{i}. object(0:) W

Port mapping table. This table MUST contain all NAT port mappings associated with this connection, including static and dynamic port mappings programmatically created via local control protocol, such as UPnP. This table MUST NOT contain dynamic NAT binding entries associated with the normal operation of NAT. At most one entry in an instance of this table can exist with all of the same values for RemoteHost, ExternalPort, and PortMappingProtocol. If the ACS attempts to set the parameters of an existing entry such that this requirement would be violated, the CPE MUST reject the request. In this case, the SetParameterValues response MUST include a SetParameterValuesFault element for each parameter in the corresponding request whose modification would have resulted in such a violation. On creation of a new table entry, the CPE MUST choose default values for ExternalPort and PortMappingProtocol such that the new entry does not conflict with any existing entry.

At most one enabled entry in this table can exist with the same values for all of RemoteHost, ExternalPort and PortMappingProtocol.

- 1.0
PortMappingEnabled boolean W Enables or disables the port mapping instance. On creation, an entry is disabled by default. false 1.0
PortMappingLeaseDuration unsignedInt W

Determines the time to live, in seconds, of a port-mapping lease, where “time to live” means the number of seconds before the port mapping expires. A value of 0 means the port mapping is static. Support for dynamic (non-static) port mappings is OPTIONAL. That is, the only value for PortMappingLeaseDuration that MUST be supported is 0. For a dynamic (non-static) port mapping, when this parameter is read, the value represents the time remaining on the port-mapping lease. That is, for a dynamic port mapping, the value counts down toward 0. When a dynamic port-mapping lease expires, the CPE MUST automatically terminate that port mapping, and MUST automatically delete the corresponding PortMapping table entry.

Active Notification requests for this parameter MAY be denied.

- 1.0
RemoteHost string W This parameter is the IP address of the source of inbound packets. An empty string indicates a “wildcard” (this will be a wildcard in most cases). CPE are REQUIRED only to support wildcards. When RemoteHost is a wildcard, all traffic sent to the ExternalPort on the WAN interface of the gateway is forwarded to the InternalClient on the InternalPort. When RemoteHost is specified as one external IP address, the NAT will only forward inbound packets from this RemoteHost to the InternalClient, all other packets will be dropped. If a CPE supports non-wildcard values for RemoteHost, it MAY additionally support the ability to have more than one port mapping with the same ExternalPort and PortMappingProtocol, but with differing values of RemoteHost. When wildcard values are used for RemoteHost and/or ExternalPort, the following precedence order applies (with the highest precedence listed first):
  1. Explicit RemoteHost, explicit ExternalPort
  2. Explicit RemoteHost, wildcard ExternalPort
  3. Wildcard RemoteHost, explicit ExternalPort
  4. Wildcard RemoteHost, wildcard ExternalPort If an incoming packet matches the criteria associated with more than one entry in this table, the CPE MUST apply the port mapping associated with the highest precedence entry. At most one entry in this table can exist with all of the same values for RemoteHost, ExternalPort, and PortMappingProtocol.
<Empty> 1.0
ExternalPort unsignedInt W The external port (or the first port of a range of external ports) that the NAT gateway would listen on for connection requests to a corresponding InternalPort. Inbound packets to this external port on the WAN interface SHOULD be forwarded to InternalClient on the InternalPort. A value of zero (0) represents a “wildcard”. If this value is a wildcard, connection request on all external ports (that are not otherwise mapped) will be forwarded to InternalClient. In the wildcard case, the value(s) of InternalPort on InternalClient are ignored. When wildcard values are used for RemoteHost and/or ExternalPort, the following precedence order applies (with the highest precedence listed first):
  1. Explicit RemoteHost, explicit ExternalPort
  2. Explicit RemoteHost, wildcard ExternalPort
  3. Wildcard RemoteHost, explicit ExternalPort
  4. Wildcard RemoteHost, wildcard ExternalPort If an incoming packet matches the criteria associated with more than one entry in this table, the CPE MUST apply the port mapping associated with the highest precedence entry. At most one entry in this table can exist with all of the same values for RemoteHost, ExternalPort, and PortMappingProtocol.
- 1.0
InternalPort unsignedInt W The port on InternalClient that the gateway SHOULD forward connection requests to. A value of zero (0) is not allowed. - 1.0
PortMappingProtocol string W

The protocol of the port mapping.

Enumeration of:

  • TCP
  • UDP At most one entry in this table can exist with all of the same values for RemoteHost, ExternalPort, and PortMappingProtocol.
- 1.0
InternalClient string(:256) W The IP address or DNS host name of an internal client (on the LAN). Support for an IP address is mandatory. If InternalClient is specified as an IP address and the LAN device’s IP address subsequently changes, the port mapping MUST remain associated with the original IP address. Support for DNS host names is OPTIONAL. If InternalClient is specified as a DNS host name and the LAN device’s IP address subsequently changes, the port mapping MUST remain associated with this LAN device. In this case, it is the responsibility of the CPE to maintain the name-to-address mapping in the event of IP address changes. This can be accomplished, for example, by assigning the DNS host name via use of DHCP option 12 (Host Name) or option 81 (FQDN). Note that the ACS can learn the host name associated with a given LAN device via the Hosts table (InternetGatewayDevice.LANDevice.{i}.Hosts). Read access to this parameter MUST always return the exact value that was last set by the ACS. For example, if the internal client is set to a DNS host name, it MUST read back as a DNS host name and not as an IP address. An empty string indicates an unconfigured InternalClient. If this parameter is unconfigured, this port mapping MUST NOT be operational. It MUST be possible to set the InternalClient to the broadcast IP address 255.255.255.255 for UDP mappings. This is to enable multiple NAT clients to use the same well-known port simultaneously. <Empty> 1.0
PortMappingDescription string(:256) W User-readable description of this port mapping. <Empty> 1.0
ExternalPortEndRange unsignedInt W Indicates the last port of the external port range that starts with ExternalPort. If an external port range is specified, then the behavior described for ExternalPort applies to all ports within the range. A value of zero (0) indicates that no external port range is specified, i.e. that the range consists only of ExternalPort. If ExternalPort is zero (wildcard), the value of this parameter MUST be ignored. If specified, the value of this parameter MUST be greater than or equal to the value of ExternalPort. 0 1.0
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANPPPConnection.{i}.Stats. object R This object contains statistics for all connections within the same WANConnectionDevice that share a common MAC address. The contents of this object SHOULD be identical for each such connection. This object is intended only for WANConnectionDevices that can support an Ethernet-layer on this interface (e.g., PPPoE, IPoE). - 1.0
EthernetBytesSent unsignedInt R

The total number of bytes transmitted, including framing characters, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetBytesReceived unsignedInt R

The total number of bytes received, including framing characters, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetPacketsSent unsignedInt R

The total number of packets transmitted over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetPacketsReceived unsignedInt R

The total number of packets which were received over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetErrorsSent unsignedInt R

The total number of outbound packets that could not be transmitted because of errors, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetErrorsReceived unsignedInt R

The total number of inbound packets that contained errors preventing them from being deliverable, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetUnicastPacketsSent unsignedInt R

The total number of packets requested for transmission which were not addressed to a multicast or broadcast address, including those that were discarded or not sent, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetUnicastPacketsReceived unsignedInt R

The total number of received packets which were not addressed to a multicast or broadcast address, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetDiscardPacketsSent unsignedInt R

The total number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted, over all connections within the same WANConnectionDevice that share a common MAC address. One possible reason for discarding such a packet could be to free up buffer space. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetDiscardPacketsReceived unsignedInt R

The total number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable, over all connections within the same WANConnectionDevice that share a common MAC address. One possible reason for discarding such a packet could be to free up buffer space. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetMulticastPacketsSent unsignedInt R

The total number of packets requested for transmission, including those that were discarded or not sent, which were addressed to a multicast address, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetMulticastPacketsReceived unsignedInt R

The total number of received packets which were addressed to a multicast address, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetBroadcastPacketsSent unsignedInt R

The total number of packets requested for transmission, including those that were discarded or not sent, which were addressed to a broadcast address, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetBroadcastPacketsReceived unsignedInt R

The total number of received packets which were addressed to a broadcast address, over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
EthernetUnknownProtoPacketsReceived unsignedInt R

The total number of packets which were discarded because of an unknown or unsupported protocol, received over all connections within the same WANConnectionDevice that share a common MAC address. The value of this counter MAY be reset to zero when the CPE is rebooted.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.Layer2Bridging. object R Layer 2 bridging configuration. Specifies bridges between layer 2 LAN and/or WAN interfaces. Bridges can be defined to include layer 2 filter criteria to selectively bridge traffic between interfaces. This object can be used to configure both 802.1D [802.1D-2004] and 802.1Q [802.1Q-2005] bridges. Not all 802.1D and 802.1Q features are modeled, and some additional features not present in either 802.1D or 802.1Q are modeled. If the Layer2Bridging object is implemented, the view that it provides of the CPE’s underlying bridging configuration MUST be consistent with the view provided by any LANDevice and WAN**Connection objects. The implications of this are explained in Annex A.6. - 1.0
MaxBridgeEntries unsignedInt R

The maximum number of entries available in the Bridge table.

Active Notification requests for this parameter MAY be denied.

- 1.0
MaxDBridgeEntries unsignedInt R The maximum number of 802.1D [802.1D-2004] entries available in the Bridge table. A positive value for this parameter implies support for 802.1D. There is no guarantee that this many 802.1D Bridges can be configured. For example, the CPE might not be able simultaneously to support both 802.1D and 802.1Q Bridges. - 1.0
MaxFilterEntries unsignedInt R

The maximum number of entries available in the Filter table.

Active Notification requests for this parameter MAY be denied.

- 1.0
MaxMarkingEntries unsignedInt R

The maximum number of entries available in the Marking table.

Active Notification requests for this parameter MAY be denied.

- 1.0
BridgeNumberOfEntries unsignedInt R Number of entries in the Bridge table. - 1.0
FilterNumberOfEntries unsignedInt R Number of entries in the Filter table. - 1.0
MarkingNumberOfEntries unsignedInt R Number of entries in the Marking table. - 1.0
AvailableInterfaceNumberOfEntries unsignedInt R Number of entries in the AvailableInterface table. - 1.0
MaxQBridgeEntries unsignedInt R The maximum number of 802.1Q [802.1Q-2005] entries available in the Bridge table. A positive value for this parameter implies support for 802.1Q. There is no guarantee that this many 802.1Q Bridges can be configured. For example, the CPE might not be able simultaneously to support both 802.1D and 802.1Q Bridges. - 1.0
MaxVLANEntries unsignedInt R The maximum number of 802.1Q [802.1Q-2005] VLANs supported per Bridge table entry. - 1.0
InternetGatewayDevice.Layer2Bridging.Bridge.{i}. object(0:) W

Bridge table. Each entry in this table represents a single physical 802.1D [802.1D-2004] or 802.1Q [802.1Q-2005] bridge. If the Bridge Port table is supported, it explicitly defines the Bridge’s interfaces. Otherwise, they are implicitly defined via the union of the FilterInterface / MarkingInterface parameters for all the Filter and Marking table entries that are associated with the Bridge.

At most one enabled entry in this table can exist with a given value for BridgeKey.

- 1.0
BridgeKey unsignedInt R Unique key for each Bridge table entry. - 1.0
BridgeStandard string W

Selects the standard supported by this Bridge table entry.

Enumeration of:

802.1D 1.0
BridgeEnable boolean W Enables or disables this Bridge table entry. false 1.0
BridgeStatus string R

The status of this Bridge table entry.

Enumeration of:

  • Disabled
  • Enabled
  • Error (OPTIONAL) The Error value MAY be used by the CPE to indicate a locally defined error condition.
Disabled 1.0
BridgeName string(:64) W Human-readable name for this Bridge table entry. <Empty> 1.0
VLANID unsignedInt(0:4094) W For an 802.1D [802.1D-2004] Bridge, which has no concept of VLANs, the value of this parameter MUST be 0. For an 802.1Q [802.1Q-2005] Bridge, this is the Bridge’s default VLAN ID, i.e. the VLAN ID that applies to Filter table entries with VLANIDFilter=-1. For an 802.1Q Bridge, the value of this parameter MUST NOT be 0. 0 1.0
PortNumberOfEntries unsignedInt R Number of entries in the Bridge Port table. 0 1.0
VLANNumberOfEntries unsignedInt R Number of entries in the Bridge VLAN table. 0 1.0
InternetGatewayDevice.Layer2Bridging.Bridge.{i}.Port.{i}. object(0:) W

Bridge Port table. If this table is supported, it MUST contain an entry for each Bridge Port.

At most one enabled entry in this table can exist with a given value for PortInterface.

- 1.0
PortEnable boolean W Enables or disables this Bridge Port table entry. false 1.0
PortInterface string(:16) W The interface associated with this Bridge Port table entry. Represents a bridge port as defined in 802.1D [802.1D-2004] and 802.1Q [802.1Q-2005]. To associate this Bridge Port with an interface listed in the AvailableInterface table, the PortInterface value is set to the value of the corresponding AvailableInterfaceKey. <Empty> 1.0
PortState string R

Bridge Port state as defined in 802.1D [802.1D-2004] and 802.1Q [802.1Q-2005].

Enumeration of:

  • Disabled
  • Blocking
  • Listening
  • Learning
  • Forwarding
  • Broken
Disabled 1.0
PVID int(1:4094) W Default Port VLAN ID as defined in 802.1Q [802.1Q-2005]. For an 802.1D [802.1D-2004] Bridge, this parameter MUST be ignored. 1 1.0
AcceptableFrameTypes string W

Bridge Port acceptable frame types as defined in 802.1Q [802.1Q-2005]. Enumeration of:

  • AdmitAll
  • AdmitOnlyVLANTagged (OPTIONAL)
  • AdmitOnlyPrioUntagged (OPTIONAL) For an 802.1D [802.1D-2004] Bridge, the value of this parameter MUST be AdmitAll.
AdmitAll 1.0
IngressFiltering boolean W Enables or disables Ingress Filtering as defined in 802.1Q [802.1Q-2005]. For an 802.1D [802.1D-2004] Bridge, the value of this parameter MUST be false. false 1.0
InternetGatewayDevice.Layer2Bridging.Bridge.{i}.VLAN.{i}. object(0:) W

Bridge VLAN table. If this table is supported, if MUST contain an entry for each VLAN known to the Bridge. This table only applies to an 802.1Q [802.1Q-2005] Bridge.

At most one enabled entry in this table can exist with a given value for VLANID.

- 1.0
VLANEnable boolean W Enables or disables this VLAN table entry. false 1.0
VLANName string(:64) W Human-readable name for this VLAN table entry. <Empty> 1.0
VLANID int(1:4094) W VLAN ID of the entry, - 1.0
InternetGatewayDevice.Layer2Bridging.Filter.{i}. object(0:) W

Filter table containing filter entries each of which is associated with one Bridge as specified by a Bridge table entry.

For both 802.1D [802.1D-2004] and 802.1Q [802.1Q-2005] Bridges, this table is used for the following:

  1. If the Bridge Port table is not supported, it implicitly specifies the Bridge interfaces (in collaboration with the Marking table).
  2. It specifies destination MAC address classification rules. For an 802.1Q Bridge, this table is also used for the following:
  3. For each VLAN ID, it specifies the interfaces that are in the VLAN’s Member Set.
  4. If the Bridge Port table is not supported, it specifies the Port VLAN ID (PVID) for each interface. This table also supports several concepts that are not covered by either 802.1D or 802.1Q:
  5. It allows a given packet to be admitted to multiple Bridges.
  6. It supports Ethertype and source MAC address classification rules.

At most one enabled entry in this table can exist with a given value for FilterKey.

- 1.0
FilterKey unsignedInt R Unique key for each Filter table entry. - 1.0
FilterEnable boolean W Enables or disables this Filter table entry. false 1.0
FilterStatus string R

The status of this Filter table entry.

Enumeration of:

  • Disabled
  • Enabled
  • Error (OPTIONAL) The Error value MAY be used by the CPE to indicate a locally defined error condition.

If the Bridge Port table is supported, but none of its entries correspond to FilterInterface, or if such an entry exists but is disabled, FilterStatus MUST NOT indicate Enabled. If the Bridge VLAN table is supported, but none of its entries correspond to VLANIDFilter, or if such an entry exists but is disabled, FilterStatus MUST NOT indicate Enabled.

Disabled 1.0
FilterBridgeReference int(-1:) W The BridgeKey value of the Bridge table entry associated with this Filter. A value of -1 indicates the Filter table entry is not associated with a Bridge (and has no effect). -1 1.0
ExclusivityOrder unsignedInt W Whether or not the Filter definition is exclusive of all others. And if the entry is exclusive, order of precedence. A value of 1 or greater indicates an Exclusive Filter, where the value 1 indicates the first entry to be considered (highest precedence). A value of 0 indicates a Non-Exclusive Filter (OPTIONAL). For each packet, if the packet matches any Exclusive Filters, the packet is assigned to the Bridge associated with the highest precedence Exclusive Filter to which it matches (lowest ExclusivityOrder value). If and only if the packet does not match any Exclusive Filters, the packet is assigned to all Bridges associated with each Non-Exclusive Filter for which it matches the defining criteria. If a packet matches no Filter, it is discarded. When the ExclusivityOrder is set to match that of an existing Exclusive Filter (1 or greater), the value for the existing entry and all higher numbered entries is incremented (lowered in precedence) to ensure uniqueness of this value. A deletion or change in ExclusivityOrder of an Exclusive Filter causes ExclusivityOrder values of other Exclusive Filters (values 1 or greater) to be compacted. Note that the use of Exclusive Filters to associate a layer 3 router interface with LAN and/or WAN interfaces via a Bridge entry overrides and updates the association between layer 3 and layer 2 objects implied by the InternetGatewayDevice object hierarchy. Support for Non-Exclusive Filter entries, i.e. entries with an ExclusivityOrder value of 0, is OPTIONAL because 802.1D [802.1D-2004] and 802.1Q [802.1Q-2005] do not consider the case of a packet potentially being admitted to more than one bridge. 0 1.0
FilterInterface string(:16) W The interface or interfaces associated with this Filter table entry. The bridge corresponding to this Filter table entry is defined to admit packets on ingress to the bridge from the specified interfaces that meet all of the criteria specified in the Filter table entry. The following values are defined.
  • To associate this Filter with a single interface listed in the AvailableInterface table, the FilterInterface value is set to the value of the corresponding AvailableInterfaceKey.
  • AllInterfaces indicates that this Filter is associated with all LAN and WAN interfaces listed in the AvailableInterface table (all entries of InterfaceType LANInterface or WANInterface). This value is DEPRECATED because of the configuration complexity it requires.
  • LANInterfaces indicates that this Filter is associated with all LAN interfaces listed in the AvailableInterface table (all entries of InterfaceType LANInterface). This value is DEPRECATED because of the configuration complexity it requires.
  • WANInterfaces indicates that this Filter is associated with all WAN interfaces listed in the AvailableInterface table (all entries of InterfaceType WANInterface). This value is DEPRECATED because of the configuration complexity it requires. An empty string indicates the Filter table entry is not associated with any interface (and has no effect)
<Empty> 1.0
VLANIDFilter int(-1:4094) W The 802.1Q [802.1Q-2005] VLAN ID associated with this Filter table entry. A value of -1 indicates that the default VLAN ID for the Bridge MUST be used instead (as specified by InternetGatewayDevice.Layer2Bridging.Bridge.{i}.VLANID for the Bridge table entry associated with this Filter table entry). For an 802.1Q bridge, the value of this parameter MUST NOT be 0, and it is interpreted as follows (more than one condition can apply, e.g. a single Filter table entry might both add an interface to a VLAN’s Member Set, and define a classification rule).
  1. If the Bridge Port table is not supported, it is a candidate to be the 802.1Q Port VLAN ID (PVID) for the interface associated with this Filter. Where there is more than one such candidate for a given interface, the PVID MUST be selected according to the ExclusivityOrder precedence rules.
  2. The interface associated with this Filter is added to the VLAN’s 802.1Q Member Set.
  3. If a classification parameter, e.g. DestMACAddressFilterList, is specified, a classification rule for this VLAN ID is added. For an 802.1D [802.1D-2004] Bridge, which has no concept of VLANs, the VLAN ID MUST be 0. This is most easily achieved by allowing this parameter to retain its default value of -1 and relying on the fact that the default VLAN ID for an 802.1D bridge will always be 0.
-1 1.0
AdmitOnlyVLANTagged boolean W 802.1Q [802.1Q-2005] Acceptable Frame Types criterion. This parameter is DEPRECATED, because it only partly models 802.1Q Acceptable Frame Types (and Ingress Filtering). The Bridge Port table SHOULD be used instead and, if supported, MUST take precedence over this parameter. If true, the Bridge admits only packets tagged with VLAN IDs that include the ingress interface in their 802.1Q Member Sets. If false, the Bridge admits both packets tagged with VLAN IDs that include the ingress interface in their 802.1Q Member Sets, and any Untagged or PriorityOnly packets. All Untagged or PriorityOnly packets are associated on ingress with the interface’s Port VLAN ID (PVID). See the description of VLANIDFilter for an explanation of how the Member Set and PVID are determined. If more than one Filter table entry is associated with a given interface, the value of AdmitOnlyVLANTagged MUST be the same for all such entries. For an 802.1D [802.1D-2004] Bridge, which has no concept of VLANs, the value of this parameter MUST be false. false 1.0
EthertypeFilterList unsignedInt[](:256) W Classification criterion. Comma-separated list (maximum number of characters 256) of unsigned integers, each representing an Ethertype value. Note that neither 802.1D [802.1D-2004] nor 802.1Q [802.1Q-2005] support classification based on Ethertype. <Empty> 1.0
EthertypeFilterExclude boolean W

If false, on ingress to the interfaces associated with this Filter, the Bridge is defined to admit only those packets that match one of the EthertypeFilterList entries (in either the Ethernet or SNAP Type header). If the EthertypeFilterList is empty, no packets are admitted. If true, on ingress to the interfaces associated with this Filter, the Bridge is defined to admit all packets except those packets that match one of the EthertypeFilterList entries (in either the Ethernet or SNAP Type header). If the EthertypeFilterList is empty, packets are admitted regardless of Ethertype.

Note that neither 802.1D [802.1D-2004] nor 802.1Q [802.1Q-2005] support classification based on Ethertype.

true 1.0
SourceMACAddressFilterList string[](:512) W Classification criterion. Comma-separated list (maximum number of characters 512) of strings, each representing a MAC Address. Each list entry MAY optionally specify a bit-mask, where matching of a packet’s MAC address is only to be done for bit positions set to one in the mask. If no mask is specified, all bits of the MAC Address are to be used for matching. For example, the list might be: 01:02:03:04:05:06, 1:22:33:00:00:00/FF:FF:FF:00:00:00, 88:77:66:55:44:33 Note that neither 802.1D [802.1D-2004] nor 802.1Q [802.1Q-2005] support classification based on source MAC address. <Empty> 1.0
SourceMACAddressFilterExclude boolean W

If false, on ingress to the interfaces associated with this Filter, the Bridge admits only those packets whose source MAC Address matches one of the SourceMACAddressFilterList entries. If the SourceMACAddressFilterList is empty, no packets are admitted. If true, on ingress to the interfaces associated with this Filter, the Bridge admits all packets except those packets whose source MAC Address matches one of the SourceMACAddressFilterList entries. If the SourceMACAddressFilterList is empty, packets are admitted regardless of MAC address.

Note that neither 802.1D [802.1D-2004] nor 802.1Q [802.1Q-2005] support classification based on source MAC address.

true 1.0
DestMACAddressFilterList string[](:512) W Classification criterion. Comma-separated list (maximum number of characters 512) of strings, each representing a MAC Address. Each list entry MAY optionally specify a bit-mask, where matching of a packet’s MAC address is only to be done for bit positions set to one in the mask. If no mask is specified, all bits of the MAC Address are to be used for matching. For example, the list might be: 01:02:03:04:05:06, 1:22:33:00:00:00/FF:FF:FF:00:00:00, 88:77:66:55:44:33 <Empty> 1.0
DestMACAddressFilterExclude boolean W If false, on ingress to the interfaces associated with this Filter, the Bridge admits only those packets whose destination MAC Address matches one of the DestMACAddressFilterList entries. If the DestMACAddressFilterList is empty, no packets are admitted. If true, on ingress to the interfaces associated with this Filter, the Bridge admits all packets except those packets whose destination MAC Address matches one of the DestMACAddressFilterList entries. If the DestMACAddressFilterList is empty, packets are admitted regardless of MAC address. true 1.0
SourceMACFromVendorClassIDFilter string(:256) W Classification criterion. A string used to identify one or more devices via DHCP for which MAC address filtering would subsequently apply. A device is considered matching if its DHCP Vendor Class Identifier (Option 60 as defined in RFC 2132 [RFC2132]) in the most recent DHCP lease acquisition or renewal matches the specified value according to the match criterion in SourceMACFromVendorClassIDMode. Case sensitive. Note that neither 802.1D [802.1D-2004] nor 802.1Q [802.1Q-2005] support classification based on source MAC address. <Empty> 1.0
SourceMACFromVendorClassIDFilterExclude boolean W

If false, on ingress to the interfaces associated with this Filter, the Bridge admits only those packets whose source MAC Address matches that of a LAN device previously identified as described in SourceMACFromVendorClassIDFilter. If SourceMACFromVendorClassIDFilter is an empty string, no packets are admitted. If true, on ingress to the interfaces associated with this Filter, the Bridge admits all packets except those packets whose source MAC Address matches that of a LAN device previously identified as described in SourceMACFromVendorClassIDFilter. If the SourceMACFromVendorClassIDFilter is an empty string, packets are admitted regardless of MAC address.

Note that neither 802.1D [802.1D-2004] nor 802.1Q [802.1Q-2005] support classification based on source MAC address.

true 1.0
DestMACFromVendorClassIDFilter string(:256) W Classification criterion. A string used to identify one or more devices via DHCP for which MAC address filtering would subsequently apply. A device is considered matching if its DHCP Vendor Class Identifier (Option 60 as defined in RFC 2132 [RFC2132]) in the most recent DHCP lease acquisition or renewal matches the specified value according to the match criterion in DestMACFromVendorClassIDMode. Case sensitive. <Empty> 1.0
DestMACFromVendorClassIDFilterExclude boolean W If false, on ingress to the interfaces associated with this Filter, the Bridge admits only those packets whose destination MAC Address matches that of a LAN device previously identified as described in DestMACFromVendorClassIDFilter. If DestMACFromVendorClassIDFilter is an empty string, no packets are admitted. If true, on ingress to the interfaces associated with this Filter, the Bridge admits all packets except those packets whose destination MAC Address matches that of a LAN device previously identified as described in DestMACFromVendorClassIDFilter. If the DestMACFromVendorClassIDFilter is an empty string, packets are admitted regardless of MAC address. true 1.0
DestMACFromVendorClassIDMode string W

DestMACFromVendorClassIDFilter pattern match criterion. Enumeration of:

Exact 1.0
SourceMACFromClientIDFilter string(:256) W Classification criterion. A string used to identify one or more devices via DHCP for which MAC address filtering would subsequently apply. A device is considered matching if its DHCP Client Identifier (Option 61 as defined in RFC 2132 [RFC2132]) in the most recent DHCP lease acquisition or renewal was equal to the specified value. The option value is binary, so an exact match is REQUIRED. Note that neither 802.1D [802.1D-2004] nor 802.1Q [802.1Q-2005] support classification based on source MAC address. <Empty> 1.0
SourceMACFromClientIDFilterExclude boolean W

If false, on ingress to the interfaces associated with this Filter, the Bridge admits only those packets whose source MAC Address matches that of a LAN device previously identified as described in SourceMACFromClientIDFilter. If SourceMACFromClientIDFilter is an empty string, no packets are admitted. If true, on ingress to the interfaces associated with this Filter, the Bridge admits all packets except those packets whose source MAC Address matches that of a LAN device previously identified as described in SourceMACFromClientIDFilter. If the SourceMACFromClientIDFilter is an empty string, packets are admitted regardless of MAC address.

Note that neither 802.1D [802.1D-2004] nor 802.1Q [802.1Q-2005] support classification based on source MAC address.

true 1.0
DestMACFromClientIDFilter string(:256) W Classification criterion. A string used to identify one or more devices via DHCP for which MAC address filtering would subsequently apply. A device is considered matching if its DHCP Client Identifier (Option 61 as defined in RFC 2132 [RFC2132]) in the most recent DHCP lease acquisition or renewal was equal to the specified value. The option value is binary, so an exact match is REQUIRED. <Empty> 1.0
DestMACFromClientIDFilterExclude boolean W If false, on ingress to the interfaces associated with this Filter, the Bridge admits only those packets whose destination MAC Address matches that of a LAN device previously identified as described in DestMACFromClientIDFilter. If DestMACFromClientIDFilter is an empty string, no packets are admitted. If true, on ingress to the interfaces associated with this Filter, the Bridge admits all packets except those packets whose destination MAC Address matches that of a LAN device previously identified as described in DestMACFromClientIDFilter. If the DestMACFromClientIDFilter is an empty string, packets are admitted regardless of MAC address. true 1.0
SourceMACFromUserClassIDFilter string(:256) W Classification criterion. A string used to identify one or more devices via DHCP for which MAC address filtering would subsequently apply. A device is considered matching if its DHCP User Class Identifier (Option 77 as defined in RFC 3004 [RFC3004]) in the most recent DHCP lease acquisition or renewal was equal to the specified value. Note that neither 802.1D [802.1D-2004] nor 802.1Q [802.1Q-2005] support classification based on source MAC address. <Empty> 1.0
SourceMACFromUserClassIDFilterExclude boolean W

If false, on ingress to the interfaces associated with this Filter, the Bridge admits only those packets whose source MAC Address matches that of a LAN device previously identified as described in SourceMACFromUserClassIDFilter. If SourceMACFromUserClassIDFilter is an empty string, no packets are admitted. If true, on ingress to the interfaces associated with this Filter, the Bridge admits all packets except those packets whose source MAC Address matches that of a LAN device previously identified as described in SourceMACFromUserClassIDFilter. If the SourceMACFromUserClassIDFilter is an empty string, packets are admitted regardless of MAC address.

Note that neither 802.1D [802.1D-2004] nor 802.1Q [802.1Q-2005] support classification based on source MAC address.

true 1.0
DestMACFromUserClassIDFilter string(:256) W Classification criterion. A string used to identify one or more devices via DHCP for which MAC address filtering would subsequently apply. A device is considered matching if its DHCP User Class Identifier (Option 77 as defined in RFC 3004 [RFC3004]) in the most recent DHCP lease acquisition or renewal was equal to the specified value. <Empty> 1.0
DestMACFromUserClassIDFilterExclude boolean W If false, on ingress to the interfaces associated with this Filter, the Bridge admits only those packets whose destination MAC Address matches that of a LAN device previously identified as described in DestMACFromUserClassIDFilter. If DestMACFromUserClassIDFilter is an empty string, no packets are admitted. If true, on ingress to the interfaces associated with this Filter, the Bridge admits all packets except those packets whose destination MAC Address matches that of a LAN device previously identified as described in DestMACFromUserClassIDFilter. If the DestMACFromUserClassIDFilter is an empty string, packets are admitted regardless of MAC address. true 1.0
SourceMACFromVendorClassIDMode string W

SourceMACFromVendorClassIDFilter pattern match criterion. Enumeration of:

Exact 1.0
InternetGatewayDevice.Layer2Bridging.Marking.{i}. object(0:) W

Marking table identifying non-default layer 2 marking behavior for packets on egress from the specified interfaces. This table is not relevant to 802.1D [802.1D-2004] Bridges, which are not VLAN-aware. For 802.1Q [802.1Q-2005] Bridges, this table is used for the following:

  1. It specifies whether VLAN tags are to be removed on egress. This table also supports several concepts that are not covered by 802.1Q:
  2. It allows the VLAN ID to be changed on egress.
  3. It allows the Ethernet Priority to be changed on egress.

At most one enabled entry in this table can exist with a given value for MarkingKey.

- 1.0
MarkingKey unsignedInt R Unique key for each Marking table entry. - 1.0
MarkingEnable boolean W Enables or disables this Marking table entry. false 1.0
MarkingStatus string R

The status of this Marking table entry.

Enumeration of:

  • Disabled
  • Enabled
  • Error (OPTIONAL) The Error value MAY be used by the CPE to indicate a locally defined error condition.

If the Bridge Port table is supported, but none of its entries correspond to MarkingInterface, or if such an entry exists but is disabled, MarkingStatus MUST NOT indicate Enabled.

Disabled 1.0
MarkingBridgeReference int(-1:) W The BridgeKey value of the Bridge table entry associated with this Marking table entry. A value of -1 indicates the Marking table entry is not associated with a Bridge (and has no effect). The effect of a Marking table entry applies only to packets that have been admitted to the specified bridge (regardless of the ingress interface). -1 1.0
MarkingInterface string(:16) W The interface or interfaces associated with this Marking table entry for which the specified marking behavior is to apply on egress from the associated bridge. The following values are defined.
  • To associate this Marking table entry with a single interface listed in the AvailableInterface table, the MarkingInterface value is set to the value of the corresponding AvailableInterfaceKey.
  • AllInterfaces indicates that this Marking table entry is associated with all LAN and WAN interfaces listed in the AvailableInterface table (all entries of InterfaceType LANInterface or WANInterface). This value is DEPRECATED because of the configuration complexity it requires.
  • LANInterfaces indicates that this Marking table entry is associated with all LAN interfaces listed in the AvailableInterface table (all entries of InterfaceType LANInterface). This value is DEPRECATED because of the configuration complexity it requires.
  • WANInterfaces indicates that this Marking table entry is associated with all WAN interfaces listed in the AvailableInterface table (all entries of InterfaceType WANInterface). This value is DEPRECATED because of the configuration complexity it requires.
  • an empty string indicates the Marking table entry table entry is not associated with any interface (and has no effect) If there is more than one enabled Marking table entry that specifies one or more of the same interfaces for the same bridge (identical values of MarkingBridgeReference), then for packets on egress from the specified bridge to those interfaces, the applied marking MUST be that specified in the Marking table entry among those in conflict with the lowest MarkingKey value. If an interface in a given bridge does not have a corresponding Marking table entry, the marking is left unchanged on egress.
<Empty> 1.0
VLANIDUntag boolean W If true, on egress to the interfaces associated with this Marking table entry, all packets are sent Untagged. If false, on egress to the interfaces associated with this Marking table entry, all packets are sent Tagged with the VLAN ID of the VLAN in which the packet is being bridged. false 1.0
VLANIDMark int(-1:4094) W The 802.1Q [802.1Q-2005] VLAN ID to be used on egress to the interfaces associated with this Marking table entry. A value of -1 indicates that the VLAN ID of the VLAN in which the packet is being bridged is to be used, i.e. no change. The value of this parameter MUST NOT be 0. If VLANIDUntag is true, then no VLAN marking is done since the tag containing the VLAN ID is removed. Note that 802.1Q does not support re-marking on egress. -1 1.0
EthernetPriorityMark int(-1:7) W Ethernet priority code (as defined in 802.1D [802.1D-2004]) to mark traffic with that falls into this Bridge on egress to the interfaces associated with this Marking table entry. A value of -1 indicates no change from the incoming packet or the mark assigned by the classifier. Note that 802.1Q [802.1Q-2005] does not support re-marking on egress. -1 1.0
EthernetPriorityOverride boolean W If false, on egress to the interfaces associated with this Marking table entry, the EthernetPriorityMark, if specified, is applied only to packets of priority 0. If true, on egress to the interfaces associated with this Marking table entry, the EthernetPriorityMark, if specified, is to be applied to all packets on this Bridge. Note that 802.1Q [802.1Q-2005] does not support re-marking on egress. false 1.0
VLANIDMarkOverride boolean W If false, on egress to the interfaces associated with this Marking table entry, the VLANIDMark, if specified, is applied only to PriorityOnly packets. If true, on egress to the interfaces associated with this Marking table entry, the VLANIDMark, if specified, is to be applied to all packets on this Bridge. If VLANIDUntag is true, then no VLAN marking is done since the tag containing the VLAN ID is removed. Note that 802.1Q [802.1Q-2005] does not support re-marking on egress. false 1.0
InternetGatewayDevice.Layer2Bridging.AvailableInterface.{i}. object(0:) R

Table containing all LAN and WAN interfaces that are available to be referenced by the Bridge table. Only interfaces that can carry layer 2 bridged traffic are included.

At most one entry in this table can exist with a given value for AvailableInterfaceKey.

- 1.0
AvailableInterfaceKey unsignedInt R

Unique key for each Interface entry.

Active Notification requests for this parameter MAY be denied.

- 1.0
InterfaceType string R

Whether the interface is a LAN-side or WAN-side interface, or a LAN-side or WAN-side connection to the Gateway’s IP router.

Enumeration of:

  • LANInterface
  • WANInterface
  • LANRouterConnection
  • WANRouterConnection

Active Notification requests for this parameter MAY be denied.

- 1.0
InterfaceReference string(:256)[](:256) R

Comma-separated list (maximum number of characters 256) of strings (maximum number of characters per item 256). Each list item MUST be the Path Name of an available LAN or WAN interface, or an empty string. This table SHOULD contain a single entry for each available LAN and WAN interface. When such an interface is modeled in more than one place within the data model, the value of this parameter MUST include the full hierarchical parameter names of all of the corresponding objects. For example, if a given Ethernet interface is present within two LANDevice instances, the value of this parameter might be: InternetGatewayDevice.LANDevice.1.LANEthernetInterfaceConfig.1, InternetGatewayDevice.LANDevice.2.LANEthernetInterfaceConfig.1 Note that the remainder of the parameter description does not refer to the possibility that the parameter value is a comma-separated list. Nevertheless, the above requirement does apply.

  • For a WAN interface, this parameter is the full hierarchical parameter name of a particular WANConnectionDevice. A WANConnectionDevice is considered available (included in this table) only if it supports layer 2 bridged traffic. That is, this table MUST include only WANConnectionDevices that contain either a WANEthernetLinkConfig object, or that contain a WANDSLLinkConfig object for which the LinkType is EoA. For example: InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2
  • For a LAN interface, this parameter is the full hierarchical parameter name of a particular LAN**InterfaceConfig object, or a WLANConfiguration object. This table SHOULD include one entry for each such object. For example: InternetGatewayDevice.LANDevice.1.LANEthernetInterfaceConfig.2
  • For a WAN-side connection to the Gateway’s IP router, this parameter is the full hierarchical parameter name of a particular WAN**Connection service. This table SHOULD include an entry for each layer 3 WAN connection. For example: InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANPPPConnection.1
  • For a LAN-side connection to the Gateway’s IP router, this parameter is the full hierarchical parameter name of a particular LANDevice. This table SHOULD include an entry for each LANDevice, each of which is associated with a LAN-side layer 3 connection to the Gateway’s IP router. For example: InternetGatewayDevice.LANDevice.2

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.QueueManagement. object R Queue management configuration object. - 1.0
Enable boolean W Enables or disables all queuing operation. - 1.0
MaxQueues unsignedInt R

The maximum number of queues supported by the CPE. Calculated as the sum of the number of different queues pointed to by Classification table. For each entry in the Classification table, the count includes a queue for each egress interface to which the corresponding classified traffic could reach.

Active Notification requests for this parameter MAY be denied.

- 1.0
MaxClassificationEntries unsignedInt R

The maximum number of entries available in the Classification table.

Active Notification requests for this parameter MAY be denied.

- 1.0
ClassificationNumberOfEntries unsignedInt R The number of entries in the Classification table. - 1.0
MaxAppEntries unsignedInt R

The maximum number of entries available in the App table.

Active Notification requests for this parameter MAY be denied.

- 1.0
AppNumberOfEntries unsignedInt R The number of entries in the App table. - 1.0
MaxFlowEntries unsignedInt R

The maximum number of entries available in the Flow table.

Active Notification requests for this parameter MAY be denied.

- 1.0
FlowNumberOfEntries unsignedInt R The number of entries in the Flow table. - 1.0
MaxPolicerEntries unsignedInt R

The maximum number of entries available in the Policer table.

Active Notification requests for this parameter MAY be denied.

- 1.0
PolicerNumberOfEntries unsignedInt R The number of entries in the Policer table. - 1.0
MaxQueueEntries unsignedInt R

The maximum number of entries available in the Queue table.

Active Notification requests for this parameter MAY be denied.

- 1.0
QueueNumberOfEntries unsignedInt R The number of entries in the Queue table. - 1.0
QueueStatsNumberOfEntries unsignedInt R The number of entries in the QueueStats table. - 1.0
DefaultForwardingPolicy unsignedInt W Identifier of the forwarding policy associated with traffic not associated with any specified classifier. - 1.0
DefaultTrafficClass int(-1:) W Identifier of the traffic class associated with traffic not associated with any specified classifier. A value of -1 indicates a null traffic class. - 1.0
DefaultPolicer int(-1:) W Instance number of the Policer table entry for traffic not associated with any specified classifier. A value of -1 indicates a null policer. - 1.0
DefaultQueue unsignedInt W

Instance number of the Queue table entry for traffic not associated with any specified classifier.

A value of 0xffffffff (-1) indicates a null queue (permitted in data model versions 1.4 and later).

- 1.0
DefaultDSCPMark int(-2:) W DSCP to mark traffic not associated with any specified classifier. A value of -1 indicates no change from the incoming packet. A value of -2 indicates automatic marking of DSCP based upon the EthernetPriority value of the incoming packet as defined in [Annex A/TR-098a1]. - 1.0
DefaultEthernetPriorityMark int(-2:) W Ethernet priority code (as defined in 802.1D) to mark traffic not associated with any specified classifier. A value of -1 indicates no change from the incoming packet. A value of -2 indicates automatic marking of EthernetPriority based upon the DSCP value of the incoming packet as defined in [Annex A/TR-098a1]. - 1.0
AvailableAppList string[](:1024) R Comma-separated list (maximum number of characters 1024) of strings. URNs, each indicating a protocol supported for use as a ProtocolIdentifier in the App table. This list MAY include any of the URNs defined in [Annex A/TR-098a1] as well as other URNs defined elsewhere. - 1.0
InternetGatewayDevice.QueueManagement.Classification.{i}. object(0:) W Classification table. - 1.0
ClassificationKey unsignedInt R

Unique key for each classification entry.

This parameter is OBSOLETED because it serves no purpose (no other parameter references it).

- 1.0
ClassificationEnable boolean W Enables or disables this classifier. false 1.0
ClassificationStatus string R

The status of this classifier.

Enumeration of:

  • Disabled
  • Enabled
  • Error (OPTIONAL) The Error value MAY be used by the CPE to indicate a locally defined error condition.
Disabled 1.0
ClassificationOrder unsignedInt(1:) W

Position of the classification entry in the order of precedence. A value of 1 indicates the first entry considered. For each packet, the highest ordered entry that matches the classification criteria is applied. All lower order entries are ignored. When this value is modified, if the value matches that of an existing entry, the Order value for the existing entry and all lower Order entries is incremented (lowered in precedence) to ensure uniqueness of this value. A deletion causes Order values to be compacted. When a value is changed, incrementing occurs before compaction.

The value on creation of a Classification table entry MUST be one greater than the largest current value.

- 1.0
ClassInterface string(:256) W Classification criterion. Specifies the LAN or WAN ingress interface associated with this entry. The content is the full hierarchical parameter name of the particular WANDevice, WANConnectionDevice, WAN**Connection, LANDevice, LAN**InterfaceConfig, or WLANConfiguration object. The following are WAN interface examples:
  • InternetGatewayDevice.WANDevice.2
  • InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANPPPConnection.1 The following are LAN interface examples:
  • InternetGatewayDevice.LANDevice.3
  • InternetGatewayDevice.LANDevice.1.LANEthernetInterfaceConfig.2
  • InternetGatewayDevice.LANDevice.1.WLANConfiguration.3 The string WAN indicates this entry is to apply to traffic entering from any WAN interface. The string LAN indicates this entry is to apply to traffic entering from any LAN interface. The string Local indicates this entry is to apply to IP-layer traffic entering from a local source within the Internet Gateway Device. An empty string indicates this classification entry is to apply to all sources.
<Empty> 1.0
DestIP string(:45) W [IPAddress] Classification criterion. Destination IP address. An empty string indicates this criterion is not used for classification. <Empty> 1.0
DestMask string(:45) W [IPAddress] Destination IP address mask. If not an empty string, only the indicated network portion of the DestIP address is to be used for classification. An empty string indicates that the full DestIP address is to be used for classification. <Empty> 1.0
DestIPExclude boolean W If false, the class includes only those packets that match the (masked) DestIP entry, if specified. If true, the class includes all packets except those that match the (masked) DestIP entry, if specified. false 1.0
SourceIP string(:45) W [IPAddress] Classification criterion. Source IP address. An empty string indicates this criterion is not used for classification. <Empty> 1.0
SourceMask string(:45) W [IPAddress] Source IP address mask. If not an empty string, only the indicated network portion of the SourceIP address is to be used for classification. An empty string indicates that the full SourceIP address is to be used for classification. <Empty> 1.0
SourceIPExclude boolean W If false, the class includes only those packets that match the (masked) SourceIP entry, if specified. If true, the class includes all packets except those that match the (masked) SourceIP entry, if specified. false 1.0
Protocol int(-1:) W Classification criterion. Protocol number. A value of -1 indicates this criterion is not used for classification. -1 1.0
ProtocolExclude boolean W If false, the class includes only those packets that match the Protocol entry, if specified. If true, the class includes all packets except those that match the Protocol entry, if specified. false 1.0
DestPort int(-1:) W Classification criterion. Destination port number. A value of -1 indicates this criterion is not used for classification. -1 1.0
DestPortRangeMax int(-1:) W Classification criterion. If specified, indicates the classification criterion is to include the port range from DestPort through DestPortRangeMax (inclusive). If specified, DestPortRangeMax MUST be greater than or equal to DestPort. A value of -1 indicates that no port range is specified. -1 1.0
DestPortExclude boolean W If false, the class includes only those packets that match the DestPort entry (or port range), if specified. If true, the class includes all packets except those that match the DestPort entry (or port range), if specified. false 1.0
SourcePort int(-1:) W Classification criterion. Source port number. A value of -1 indicates this criterion is not used for classification. -1 1.0
SourcePortRangeMax int(-1:) W Classification criterion. If specified, indicates the classification criterion is to include the port range from SourcePort through SourcePortRangeMax (inclusive). If specified, SourcePortRangeMax MUST be greater than or equal to SourcePort. A value of -1 indicates that no port range is specified. -1 1.0
SourcePortExclude boolean W If false, the class includes only those packets that match the SourcePort entry (or port range), if specified. If true, the class includes all packets except those that match the SourcePort entry (or port range), if specified. false 1.0
SourceMACAddress string(:17) W [MACAddress] Classification criterion. Source MAC Address. An empty string indicates this criterion is not used for classification. <Empty> 1.0
SourceMACMask string(:45) W [IPAddress] Bit-mask for the MAC address, where matching of a packet’s MAC address with the SourceMACAddress is only to be done for bit positions set to one in the mask. A mask of FF:FF:FF:FF:FF:FF or an empty string indicates all bits of the SourceMACAdress are to be used for classification. <Empty> 1.0
SourceMACExclude boolean W If false, the class includes only those packets that match the (masked) SourceMACAddress entry, if specified. If true, the class includes all packets except those that match the (masked) SourceMACAddress entry, if specified. false 1.0
DestMACAddress string(:17) W [MACAddress] Classification criterion. Destination MAC Address. An empty string indicates this criterion is not used for classification. The use of destination MAC address as a classification criterion is primarily useful only for bridged traffic. <Empty> 1.0
DestMACMask string(:45) W [IPAddress] Bit-mask for the MAC address, where matching of a packet’s MAC address with the DestMACAddress is only to be done for bit positions set to one in the mask. A mask of FF:FF:FF:FF:FF:FF or an empty string indicates all bits of the DestMACAdress are to be used for classification. <Empty> 1.0
DestMACExclude boolean W If false, the class includes only those packets that match the (masked) DestMACAddress entry, if specified. If true, the class includes all packets except those that match the (masked) DestMACAddress entry, if specified. false 1.0
Ethertype int(-1:) W Classification criterion. Ethertype as indicated in either the Ethernet or SNAP Type header. A value of -1 indicates this criterion is not used for classification. -1 1.0
EthertypeExclude boolean W If false, the class includes only those packets that match the Ethertype entry, if specified. If true, the class includes all packets except those that match the Ethertype entry, if specified. false 1.0
SSAP int(-1:) W Classification criterion. SSAP element in the LLC header. A value of -1 indicates this criterion is not used for classification. -1 1.0
SSAPExclude boolean W If false, the class includes only those packets that match the SSAP entry, if specified. If true, the class includes all packets except those that match the SSAP entry, if specified. false 1.0
DSAP int(-1:) W Classification criterion. DSAP element in the LLC header. A value of -1 indicates this criterion is not used for classification. -1 1.0
DSAPExclude boolean W If false, the class includes only those packets that match the DSAP entry, if specified. If true, the class includes all packets except those that match the DSAP entry, if specified. false 1.0
LLCControl int(-1:) W Classification criterion. Control element in the LLC header. A value of -1 indicates this criterion is not used for classification. -1 1.0
LLCControlExclude boolean W If false, the class includes only those packets that match the LLCControl entry, if specified. If true, the class includes all packets except those that match the LLCControl entry, if specified. false 1.0
SNAPOUI int(-1:) W Classification criterion. OUI element in the SNAP header. A value of -1 indicates this criterion is not used for classification. -1 1.0
SNAPOUIExclude boolean W If false, the class includes only those packets that match the SNAPOUI entry, if specified. If true, the class includes all packets except those that match the SNAPOUI entry, if specified. false 1.0
SourceVendorClassID string(:256) W Classification criterion. Used to identify one or more LAN devices, value of the DHCP Vendor Class Identifier (Option 60) as defined in RFC 2132 [RFC2132], matched according to the criterion in SourceVendorClassIDMode. Case sensitive. An empty string indicates this criterion is not used for classification. <Empty> 1.0
SourceVendorClassIDExclude boolean W If false, the class includes only those packets sourced from LAN devices that match the SourceVendorClassID entry, if specified. If true, the class includes all packets except those sourced from LAN devices that match the SourceVendorClassID entry, if specified. false 1.0
SourceVendorClassIDMode string W

SourceVendorClassID pattern match criterion. Enumeration of:

  • Exact
  • Prefix
  • Suffix
  • Substring For example, if SourceVendorClassID is “Example” then an Option 60 value of “Example device” will match with SourceVendorClassIDMode values of Prefix or Substring, but not with Exact or Suffix.
Exact 1.0
DestVendorClassID string(:256) W Classification criterion. Used to identify one or more LAN devices, value of the DHCP Vendor Class Identifier (Option 60) as defined in RFC 2132 [RFC2132], matched according to the criterion in DestVendorClassIDMode. Case sensitive. An empty string indicates this criterion is not used for classification. <Empty> 1.0
DestVendorClassIDExclude boolean W If false, the class includes only those packets destined for LAN devices that match the DestVendorClassID entry, if specified. If true, the class includes all packets except those destined for LAN devices that match the DestVendorClassID entry, if specified. false 1.0
DestVendorClassIDMode string W

DestVendorClassID pattern match criterion. Enumeration of:

  • Exact
  • Prefix
  • Suffix
  • Substring For example, if DestVendorClassID is “Example” then an Option 60 value of “Example device” will match with DestVendorClassIDMode values of Prefix or Substring, but not with Exact or Suffix.
Exact 1.0
SourceClientID string(:256) W Classification criterion. Used to identify one or more LAN devices, value of the DHCP Client Identifier (Option 61) as defined in RFC 2132 [RFC2132]. The option value is binary, so an exact match is REQUIRED. An empty string indicates this criterion is not used for classification. <Empty> 1.0
SourceClientIDExclude boolean W If false, the class includes only those packets sourced from LAN devices that match the SourceClientID entry, if specified. If true, the class includes all packets except those sourced from LAN devices that match the SourceClientID entry, if specified. false 1.0
DestClientID string(:256) W Classification criterion. Used to identify one or more LAN devices, value of the DHCP Client Identifier (Option 61) as defined in RFC 2132 [RFC2132]. The option value is binary, so an exact match is REQUIRED. An empty string indicates this criterion is not used for classification. <Empty> 1.0
DestClientIDExclude boolean W If false, the class includes only those packets destined for LAN devices that match the DestClientID entry, if specified. If true, the class includes all packets except those destined for LAN devices that match the DestClientID entry, if specified. false 1.0
SourceUserClassID string(:256) W Classification criterion. Used to identify one or more LAN devices, value of the DHCP User Class Identifier (Option 77) as defined in RFC 3004 [RFC3004]. An empty string indicates this criterion is not used for classification. <Empty> 1.0
SourceUserClassIDExclude boolean W If false, the class includes only those packets sourced from LAN devices that match the SourceUserClassID entry, if specified. If true, the class includes all packets except those sourced from LAN devices that match the SourceUserClassID entry, if specified. false 1.0
DestUserClassID string(:256) W Classification criterion. Used to identify one or more LAN devices, value of the DHCP User Class Identifier (Option 77) as defined in RFC 3004 [RFC3004]. An empty string indicates this criterion is not used for classification. <Empty> 1.0
DestUserClassIDExclude boolean W If false, the class includes only those packets destined for LAN devices that match the DestUserClassID entry, if specified. If true, the class includes all packets except those destined for LAN devices that match the DestUserClassID entry, if specified. false 1.0
SourceVendorSpecificInfo string(:256) W Classification criterion. Used to identify one or more LAN devices, value of the DHCP Vendor-specific Information (Option 125) as defined in RFC 3925 [RFC3925], matched according to the criteria in SourceVendorSpecificInfoEnterprise, SourceVendorSpecificInfoSubOption and SourceVendorSpecificInfoMode. Case sensitive. An empty string indicates this criterion is not used for classification. <Empty> 1.0
TCPACK boolean W Classification criterion. If false, this criterion is not used for classification. If true, this criterion matches with all TCP segments that have the ACK control bit set. false 1.0
TCPACKExclude boolean W If false, the class includes only those packets that match the TCPACK entry, if specified. If true, the class includes all packets except those that match the TCPACK entry, if specified. false 1.0
IPLengthMin unsignedInt W Classification criterion. Minimum IP Packet Length (including header) in bytes. 0 1.0
IPLengthMax unsignedInt W Classification criterion. Maximum IP Packet Length (including header) in bytes. A value of zero indicates that no maximum is specified (an umlimited maximum length). 0 1.0
IPLengthExclude boolean W If false, the class includes only those packets whose length (including header) falls within the inclusive range IPLengthMin through IPLengthMax. A value of zero for both IPLengthMin and IPLengthMax allows any length packet. An equal non-zero value of IPLengthMin and IPLengthMax allows only a packet with the exact length specified. If true, the class includes all packets except those whose length (including header) falls within the inclusive range IPLengthMin through IPLengthMax. false 1.0
DSCPCheck int(-1:) W Classification criterion. DiffServ codepoint (defined in RFC 2474 [RFC2474]). If set to a Class Selector Codepoint (defined in RFC 2474), all DSCP values that match the first 3 bits will be considered a valid match. A value of -1 indicates this criterion is not used for classification. -1 1.0
DSCPExclude boolean W If false, the class includes only those packets that match the DSCPCheck entry, if specified. If true, the class includes all packets except those that match the DSCPCheck entry, if specified. false 1.0
DSCPMark int(-2:) W Classification result. DSCP to mark traffic with that falls into this classification entry. A value of -1 indicates no change from the incoming packet. A value of -2 indicates automatic marking of DSCP based upon the EthernetPriority value of the incoming packet as defined in [Annex A/TR-098a1]. -1 1.0
EthernetPriorityCheck int(-1:) W Classification criterion. Current Ethernet priority as defined in 802.1D. A value of -1 indicates this criterion is not used for classification. -1 1.0
EthernetPriorityExclude boolean W If false, the class includes only those packets that match the EthernetPriorityCheck entry, if specified. If true, the class includes all packets except those that match the EthernetPriorityCheck entry, if specified. false 1.0
EthernetPriorityMark int(-2:) W Classification result. Ethernet priority code (as defined in 802.1D) to mark traffic with that falls into this classification entry. A value of -1 indicates no change from the incoming packet. A value of -2 indicates automatic marking of EthernetPriority based upon the DSCP value of the incoming packet as defined in [Annex A/TR-098a1]. -1 1.0
VLANIDCheck int(-1:) W Classification criterion. Current Ethernet VLAN ID as defined in 802.1Q. A value of -1 indicates this criterion is not used for classification. -1 1.0
VLANIDExclude boolean W If false, the class includes only those packets that match the VLANIDCheck entry, if specified. If true, the class includes all packets except those that match the VLANIDCheck entry, if specified. false 1.0
OutOfBandInfo int(-1:) W Classification criterion. Allows traffic to be distinguished based on out-of-band information such as physical port or application ID. Primarily intended for, but not restricted to, locally sourced traffic. If specified, this entry applies to traffic with matching out-of-band information. A value of -1 indicates this criterion is not used for classification. -1 1.0
ForwardingPolicy unsignedInt W Classification result. Identifier of the forwarding policy associated with traffic that falls in this classification. 0 1.0
TrafficClass int(-1:) W Classification result. Identifier of the traffic class associated with traffic that falls in this classification. If specified, at least one Queue table entry MUST include this traffic class in its TrafficClass parameter (which is a comma-separated list). A value of -1 indicates a null traffic class. TrafficClass, ClassQueue and ClassApp are mutually exclusive and one of the three MUST be specified. If TrafficClass and ClassQueue are null, ClassApp MUST be specified, and vice versa. -1 1.0
ClassPolicer int(-1:) W Classification result. Instance number of the Policer table entry for traffic that falls in this classification. A value of -1 indicates a null policer. -1 1.0
ClassQueue int(-1:) W Classification result. Instance number of the Queue table entry for traffic that falls in this classification. A value of -1 indicates a null queue. TrafficClass, ClassQueue and ClassApp are mutually exclusive and one of the three MUST be specified. If TrafficClass and ClassQueue are null, ClassApp MUST be specified, and vice versa. -1 1.0
ClassApp int(-1:) W Classification result. Instance number of the App table entry for traffic that falls in this classification. A value of -1 indicates a null App table entry. TrafficClass, ClassQueue and ClassApp are mutually exclusive and one of the three MUST be specified. If TrafficClass and ClassQueue are null, ClassApp MUST be specified, and vice versa. -1 1.0
SourceVendorSpecificInfoExclude boolean W If false, the class includes only those packets sourced from LAN devices that match the SourceVendorSpecificInfo entry, if specified. If true, the class includes all packets except those sourced from LAN devices that match the SourceVendorSpecificInfo entry, if specified. false 1.0
SourceVendorSpecificInfoEnterprise unsignedInt W SourceVendorSpecificInfo Enterprise Number as defined in RFC 3925 [RFC3925]. The default value (0) is assigned to IANA and will probably need to be replaced with an appropriate enterprise number. 0 1.0
SourceVendorSpecificInfoSubOption int(0:255) W SourceVendorSpecificInfo Sub Option Code as defined in RFC 3925 [RFC3925]. 0 1.0
SourceVendorSpecificInfoMode string W

SourceVendorSpecificInfo pattern match criterion.

Enumeration of:

  • Exact
  • Prefix
  • Suffix
  • Substring
Exact 1.0
DestVendorSpecificInfo string(:256) W Classification criterion. Used to identify one or more LAN devices, value of the DHCP Vendor-specific Information (Option 125) as defined in RFC 3925 [RFC3925], matched according to the criteria in DestVendorSpecificInfoEnterprise, DestVendorSpecificInfoSubOption and DestVendorSpecificInfoMode. An empty string indicates this criterion is not used for classification. <Empty> 1.0
DestVendorSpecificInfoExclude boolean W If false, the class includes only those packets destined for LAN devices that match the DestVendorSpecificInfo entry, if specified. If true, the class includes all packets except those destined for LAN devices that match the DestVendorSpecificInfo entry, if specified. false 1.0
DestVendorSpecificInfoEnterprise unsignedInt W DestVendorSpecificInfo Enterprise Number as defined in RFC 3925 [RFC3925]. The default value (0) is assigned to IANA and will probably need to be replaced with an appropriate enterprise number. 0 1.0
DestVendorSpecificInfoSubOption int(0:255) W DestVendorSpecificInfo Sub Option Code as defined in RFC 3925 [RFC3925]. 0 1.0
DestVendorSpecificInfoMode string W

DestVendorSpecificInfo pattern match criterion.

Enumeration of:

  • Exact
  • Prefix
  • Suffix
  • Substring
Exact 1.0
InternetGatewayDevice.QueueManagement.App.{i}. object(0:) W Application table. - 1.0
AppKey unsignedInt R

Unique key for each App table entry.

This parameter is OBSOLETED because it serves no purpose (no other parameter references it).

- 1.0
AppEnable boolean W Enables or disables this App table entry. false 1.0
AppStatus string R

The status of this App table entry.

Enumeration of:

  • Disabled
  • Enabled
  • Error (OPTIONAL) The Error value MAY be used by the CPE to indicate a locally defined error condition.
Disabled 1.0
ProtocolIdentifier string(:256) W URN identifying the protocol associated with the given application. A set of defined URNs is given in [Annex A/TR-098a1]. <Empty> 1.0
AppName string(:64) W Human-readable name associated with this entry in the App table. <Empty> 1.0
AppDefaultForwardingPolicy unsignedInt W Identifier of the forwarding policy associated with traffic associated with this App table entry, but not associated with any specified flow. 0 1.0
AppDefaultTrafficClass int(-1:) W Identifier of the traffic class associated with traffic associated with this App table entry, but not associated with any specified flow. A value of -1 indicates a null traffic class. AppDefaultTrafficClass and AppDefaultQueue MUST NOT both be specified. -1 1.0
AppDefaultPolicer int(-1:) W Instance number of the Policer table entry for traffic associated with this App table entry, but not associated with any specified flow. A value of -1 indicates a null policer. -1 1.0
AppDefaultQueue int(-1:) W

Instance number of the Queue table entry for traffic associated with this App table entry, but not associated with any specified flow. A value of -1 indicates a null queue.

AppDefaultTrafficClass and AppDefaultQueue MUST NOT both be specified.

-1 1.0
AppDefaultDSCPMark int(-2:) W DSCP to mark traffic associated with this App table entry, but not associated with any specified flow. A value of -1 indicates no change from the incoming packet. A value of -2 indicates automatic marking of DSCP based upon the EthernetPriority value of the incoming packet as defined in [Annex A/TR-098a1]. -1 1.0
AppDefaultEthernetPriorityMark int(-2:) W Ethernet priority code (as defined in 802.1D) to mark traffic associated with this App table entry, but not associated with any specified flow. A value of -1 indicates no change from the incoming packet. A value of -2 indicates automatic marking of EthernetPriority based upon the DSCP value of the incoming packet as defined in [Annex A/TR-098a1]. -1 1.0
InternetGatewayDevice.QueueManagement.Flow.{i}. object(0:) W Flow table. - 1.0
FlowKey unsignedInt R

Unique key for each Flow table entry.

This parameter is OBSOLETED because it serves no purpose (no other parameter references it).

- 1.0
FlowEnable boolean W Enables or disables this Flow table entry. false 1.0
FlowStatus string R

The status of this Flow table entry.

Enumeration of:

  • Disabled
  • Enabled
  • Error (OPTIONAL) The Error value MAY be used by the CPE to indicate a locally defined error condition.
Disabled 1.0
FlowType string(:256) W URN identifying the type of flow to be associated with the specified queue and policer. A set of defined URNs is given in [Annex A/TR-098a1]. <Empty> 1.0
FlowTypeParameters string(:256) W List of name-value pairs representing additional criteria to identify the flow type. The use and interpretation is specific to the particular FlowType URN.Encoded using the “x-www-form-urlencoded” content type defined in [HTML4.01]. <Empty> 1.0
FlowName string(:64) W Human-readable name associated with this entry in the Flow table. <Empty> 1.0
AppIdentifier int(-1:) W Instance number of the App table entry associated with this flow. A value of -1 indicates the flow table is not associated with any App table entry. -1 1.0
FlowForwardingPolicy unsignedInt W Identifier of the forwarding policy associated with this flow. 0 1.0
FlowTrafficClass int(-1:) W Identifier of the traffic class associated with this flow. A value of -1 indicates a null traffic class. FlowTrafficClass and FlowQueue MUST NOT both be specified. -1 1.0
FlowPolicer int(-1:) W Instance number of the Policer table entry for traffic that falls in this flow. A value of -1 indicates a null policer. -1 1.0
FlowQueue int(-1:) W

Instance number of the Queue table entry for traffic that falls in this flow. A value of -1 indicates a null queue.

FlowTrafficClass and FlowQueue MUST NOT both be specified.

-1 1.0
FlowDSCPMark int(-2:) W DSCP to mark traffic with that falls into this flow. A value of -1 indicates no change from the incoming packet. A value of -2 indicates automatic marking of DSCP based upon the EthernetPriority value of the incoming packet as defined in [Annex A/TR-098a1]. -1 1.0
FlowEthernetPriorityMark int(-2:) W Ethernet priority code (as defined in 802.1D) to mark traffic with that falls into this flow. A value of -1 indicates no change from the incoming packet. A value of -2 indicates automatic marking of EthernetPriority based upon the DSCP value of the incoming packet as defined in [Annex A/TR-098a1]. -1 1.0
InternetGatewayDevice.QueueManagement.Policer.{i}. object(0:) W Policer table. - 1.0
PolicerKey unsignedInt R

Unique key for each policer entry.

This parameter is OBSOLETED because it serves no purpose (no other parameter references it).

- 1.0
PolicerEnable boolean W Enables or disables this policer. false 1.0
PolicerStatus string R

The status of this policer.

Enumeration of:

  • Disabled
  • Enabled
  • Error (OPTIONAL) The Error value MAY be used by the CPE to indicate a locally defined error condition.
Disabled 1.0
CommittedRate unsignedInt W Committed rate allowed for this policer in bits-per-second. 0 1.0
CommittedBurstSize unsignedInt W Committed Burstsize in bytes. 0 1.0
ExcessBurstSize unsignedInt W Excess Burstsize in bytes. Applied for a SingleRateThreeColor meter. 0 1.0
PeakRate unsignedInt W Peak rate allowed for this Meter in bits-per-second. Applied for TwoRateThreeColor meters. 0 1.0
PeakBurstSize unsignedInt W Peak Burstsize in bytes. Applied for TwoRateThreeColor meters. 0 1.0
MeterType string W

Identifies the method of traffic measurement to be used for this policer. Enumeration of:

SimpleTokenBucket 1.0
PossibleMeterTypes string[] R

Comma-separated list of strings. Supported meter types.

Each list item is an enumeration of:

  • SimpleTokenBucket
  • SingleRateThreeColor
  • TwoRateThreeColor

Active Notification requests for this parameter MAY be denied.

- 1.0
ConformingAction string W

Instructions for how to handle traffic that is conforming. Possible patterns:

  • Null
  • Drop
  • Count (DEPRECATED)
  • [0-9]|[1-5][0-9]|6[0-3] ()
  • :[0-7] ()
  • ([0-9]|[1-5][0-9]|6[0-3]):[0-7] () Null corresponds with no action. A {{pattern: reference to deprecated pattern InternetGatewayDevice.QueueManagement.Policer.{i}.ConformingAction.Count}} action (and only the {{pattern: reference to deprecated pattern InternetGatewayDevice.QueueManagement.Policer.{i}.ConformingAction.Count}} action) increases the meter instance count statistics in the {{param: reference to deprecated parameter InternetGatewayDevice.QueueManagement.Policer.{i}.CountedPackets}} and {{param: reference to deprecated parameter InternetGatewayDevice.QueueManagement.Policer.{i}.CountedBytes}} parameters. {{pattern: reference to deprecated pattern InternetGatewayDevice.QueueManagement.Policer.{i}.ConformingAction.Count}} actions are DEPRECATED because they can not be combined with other actions, e.g. marking actions. is an unsigned integer that corresponds with a mark action overwriting the traffic’s DSCP with the configured DSCP. <:Ethernet Priority> is a colon (“:”) followed by an unsigned integer (no white space). It corresponds with a mark action overwriting the traffic’s Ethernet Priority with the configured Ethernet Priority. is an unsigned integer followed by a colon (“:”) and a second unsigned integer (no white space). It corresponds with a mark action overwriting the traffic’s DSCP and Ethernet Priority with the configured values. For example, “24” specifies a DSCP value of 24, “:3” specifies an Ethernet Priority of 3, and “24:3” specifies both.
Null 1.0
PartialConformingAction string W

Instructions for how to handle traffic that is partially conforming (colored yellow). Possible patterns:

  • Null
  • Drop
  • Count (DEPRECATED)
  • [0-9]|[1-5][0-9]|6[0-3] ()
  • :[0-7] ()
  • ([0-9]|[1-5][0-9]|6[0-3]):[0-7] () Null corresponds with no action. A {{pattern: reference to deprecated pattern InternetGatewayDevice.QueueManagement.Policer.{i}.PartialConformingAction.Count}} action (and only the {{pattern: reference to deprecated pattern InternetGatewayDevice.QueueManagement.Policer.{i}.PartialConformingAction.Count}} action) increases the meter instance count statistics in the {{param: reference to deprecated parameter InternetGatewayDevice.QueueManagement.Policer.{i}.CountedPackets}} and {{param: reference to deprecated parameter InternetGatewayDevice.QueueManagement.Policer.{i}.CountedBytes}} parameters. {{pattern: reference to deprecated pattern InternetGatewayDevice.QueueManagement.Policer.{i}.PartialConformingAction.Count}} actions are DEPRECATED because they can not be combined with other actions, e.g. marking actions. is an unsigned integer that corresponds with a mark action overwriting the traffic’s DSCP with the configured DSCP.Only applies for three-color meters. <:Ethernet Priority> is a colon (“:”) followed by an unsigned integer (no white space). It corresponds with a mark action overwriting the traffic’s Ethernet Priority with the configured Ethernet Priority. is an unsigned integer followed by a colon (“:”) and a second unsigned integer (no white space). It corresponds with a mark action overwriting the traffic’s DSCP and Ethernet Priority with the configured values. For example, “24” specifies a DSCP value of 24, “:3” specifies an Ethernet Priority of 3, and “24:3” specifies both.
Drop 1.0
NonConformingAction string W

Instructions for how to handle traffic that is non-conforming. Possible patterns:

  • Null
  • Drop
  • Count (DEPRECATED)
  • [0-9]|[1-5][0-9]|6[0-3] ()
  • :[0-7] ()
  • ([0-9]|[1-5][0-9]|6[0-3]):[0-7] () Null corresponds with no action. A {{pattern: reference to deprecated pattern InternetGatewayDevice.QueueManagement.Policer.{i}.NonConformingAction.Count}} action (and only the {{pattern: reference to deprecated pattern InternetGatewayDevice.QueueManagement.Policer.{i}.NonConformingAction.Count}} action) increases the meter instance count statistics in the {{param: reference to deprecated parameter InternetGatewayDevice.QueueManagement.Policer.{i}.CountedPackets}} and {{param: reference to deprecated parameter InternetGatewayDevice.QueueManagement.Policer.{i}.CountedBytes}} parameters. {{pattern: reference to deprecated pattern InternetGatewayDevice.QueueManagement.Policer.{i}.NonConformingAction.Count}} actions are DEPRECATED because they can not be combined with other actions, e.g. marking actions. is an unsigned integer that corresponds with a mark action overwriting the traffic’s DSCP with the configured DSCP. <:Ethernet Priority> is a colon (“:”) followed by an unsigned integer (no white space). It corresponds with a mark action overwriting the traffic’s Ethernet Priority with the configured Ethernet Priority. is an unsigned integer followed by a colon (“:”) and a second unsigned integer (no white space). It corresponds with a mark action overwriting the traffic’s DSCP and Ethernet Priority with the configured values. For example, “24” specifies a DSCP value of 24, “:3” specifies an Ethernet Priority of 3, and “24:3” specifies both.
Drop 1.0
CountedPackets unsignedInt R

Number of Packets counted as result of a Count meter action. This parameter is DEPRECATED because the Count meter action is DEPRECATED.

Active Notification requests for this parameter MAY be denied.

0 1.0
CountedBytes unsignedInt R

Number of Bytes counted as result of a Count meter action. This parameter is DEPRECATED because the Count meter action is DEPRECATED.

Active Notification requests for this parameter MAY be denied.

0 1.0
TotalCountedPackets unsignedInt R

Total number of Packets counted by this policer, regardless of meter action.

Active Notification requests for this parameter MAY be denied.

0 1.0
TotalCountedBytes unsignedInt R

Total number of Bytes counted by this policer, regardless of meter action.

Active Notification requests for this parameter MAY be denied.

0 1.0
ConformingCountedPackets unsignedInt R

Number of conforming Packets counted by this policer, regardless of meter action.

Active Notification requests for this parameter MAY be denied.

0 1.0
ConformingCountedBytes unsignedInt R

Number of conforming Bytes counted by this policer, regardless of meter action.

Active Notification requests for this parameter MAY be denied.

0 1.0
PartiallyConformingCountedPackets unsignedInt R

Number of partially conforming Packets counted by this policer, regardless of meter action.

Active Notification requests for this parameter MAY be denied.

0 1.0
PartiallyConformingCountedBytes unsignedInt R

Number of partially conforming Bytes counted by this policer, regardless of meter action.

Active Notification requests for this parameter MAY be denied.

0 1.0
NonConformingCountedPackets unsignedInt R

Number of non-conforming Packets counted by this policer, regardless of meter action.

Active Notification requests for this parameter MAY be denied.

0 1.0
NonConformingCountedBytes unsignedInt R

Number of non-conforming Bytes counted by this policer, regardless of meter action.

Active Notification requests for this parameter MAY be denied.

0 1.0
InternetGatewayDevice.QueueManagement.Queue.{i}. object(0:) W

Queue table.

This table can contain hardware queues. The CPE MAY refuse to allow hardware queues to be deleted.

- 1.0
QueueKey unsignedInt R

Unique key for each queue entry.

This parameter is OBSOLETED because it serves no purpose (no other parameter references it).

- 1.0
QueueEnable boolean W Enables or disables this queue. false 1.0
QueueStatus string R

The status of this queue.

Enumeration of:

  • Disabled
  • Enabled
  • Error (OPTIONAL) The Error value MAY be used by the CPE to indicate a locally defined error condition.
Disabled 1.0
TrafficClasses unsignedInt[](:256) W Comma-separated list (maximum number of characters 256) of unsigned integers. Identifies the set of traffic classes associated with this queue. If this list is empty then traffic can be sent to this queue only as a result of a direct reference from a Classification, App or Flow table entry, e.g. via the Classification table’s ClassQueue parameter. If this list is non-empty then traffic can additionally be sent to this queue if a Classification, App or Flow table entry specifies a traffic class, e.g. via the Classification table’s TrafficClass parameter. If more than one queue on a given egress interface is associated with a given traffic class, the implementation will choose which queue to send traffic of this class to. <Empty> 1.0
QueueInterface string(:256) W Egress interfaces for which the specified queue MUST exist. This parameter MUST be in one of the following forms: The full hierarchical parameter name of the particular WANDevice, WANConnectionDevice, WAN**Connection, LANDevice, LAN**InterfaceConfig, or WLANConfiguration object. The string WAN, which indicates this entry applies to all WAN interfaces. The string LAN, which indicates this entry applies to all LAN interfaces. An empty string, which indicates this classification entry is to apply to all interfaces. Packets classified into this queue that exit through any other interface MUST instead use the default queuing behavior specified in the Queue table entry referenced by InternetGatewayDevice.QueueManagement.DefaultQueue. For the default queue itself (the Queue table entry referenced by InternetGatewayDevice.QueueManagement.DefaultQueue), the value of the QueueInterface parameter MUST be ignored. That is, the default queue MUST exist on all egress interfaces. <Empty> 1.0
QueueBufferLength unsignedInt R

Number of bytes in the buffer.

Queue buffer size for all egress interfaces for which this queue exists. If the buffer size is not the same for all such egress interfaces, this parameter MUST be 0.

- 1.0
QueueWeight unsignedInt W Weight of this queue in case of WFQ or WRR, but only used for queues of equal precedence. 0 1.0
QueuePrecedence unsignedInt(1:) W Precedence of this queue relative to others. Lower numbers imply greater precedence. 1 1.0
REDThreshold unsignedInt(:100) W Random Early Detection threshold, used only when DropAlgorithm is RED. This is the minimum threshold (min_th) and is measured as a percentage of the queue size. If the value is set to zero, the CPE MUST choose a sensible value, e.g. 5 (but the value MUST still read back as zero). In this version of the data model, there is no way to set the maximum threshold (max_th). The CPE MUST choose a sensible value, e.g. three times the minimum threshold. In this version of the data model, there is no way to set the RED weight (w_q). The CPE MUST choose a sensible value, e.g. 0.002. 0 1.0
REDPercentage unsignedInt(:100) W Random Early Detection percentage, used only when DropAlgorithm is RED. This is the maximum value of the packet marking probability (max_p). If the value is set to zero, the CPE MUST choose a sensible value, e.g. 10 (but the value MUST still read back as zero). In this version of the data model, there is no way to set the RED weight (w_q). The CPE MUST choose a sensible value, e.g. 0.002. 0 1.0
DropAlgorithm string W

Dropping algorithm used for this queue if congested.

Enumeration of:

  • RED (Random Early Detection [RED])
  • DT (Drop Tail)
  • WRED (Weighted RED)
  • BLUE ([BLUE])
DT 1.0
SchedulerAlgorithm string W

Scheduling Algorithm used by scheduler.

Enumeration of:

  • WFQ (Weighted Fair Queueing)
  • WRR (Weighted Round Robin)
  • SP (Strict Priority)
SP 1.0
ShapingRate int(-1:) W Rate to shape this queue’s traffic to. For leaky bucket (constant rate shaping), this is the constant rate. For token bucket (variable rate shaping), this is the average rate. If <= 100, in percent of the rate of the highest rate-constrained layer over which the packet will travel on egress. If > 100, in bits per second. A value of -1 indicates no shaping. For example, for packets destined for a WAN DSL interface, if the egress will be on a PPP or IP link with a specified ShapingRate, the percentage is calculated relative to this rate. Otherwise, if the ATM layer is rate-constrained, then the rate is calculated relative to this rate. Otherwise, the rate is calculated relative to the physical-layer DSL rate. -1 1.0
ShapingBurstSize unsignedInt W Burst size in bytes. For both leaky bucket (constant rate shaping) and token bucket (variable rate shaping) this is the bucket size and is therefore the maximum burst size. 0 1.0
InternetGatewayDevice.QueueManagement.QueueStats.{i}. object(0:) W

Queue statistics table. This table is managed by the ACS, which will create entries only for those {Queue, Interface} combinations for which statistics are to be collected.

At most one enabled entry in this table can exist with the same values for both Queue and Interface.

- 1.0
Enable boolean W Enables or disables this object. false 1.0
Status string R

The status of this object.

Enumeration of:

  • Disabled
  • Enabled (Enabled and {Queue,Interface} is valid)
  • Error (Enabled but {Queue,Interface} is invalid)
Disabled 1.0
Queue unsignedInt W Instance number of the Queue table entry with which this object is associated. 0 1.0
Interface string(:256) W Egress interface for which this object contains statistics. This parameter MUST be the full hierarchical parameter name of the particular WANDevice, WANConnectionDevice, WAN**Connection, LANDevice, LAN**InterfaceConfig, or WLANConfiguration object. <Empty> 1.0
OutputPackets unsignedInt R

Number of packets output through the queue.

Active Notification requests for this parameter MAY be denied.

0 1.0
OutputBytes unsignedInt R

Number of bytes output through the queue.

Active Notification requests for this parameter MAY be denied.

0 1.0
DroppedPackets unsignedInt R

Number of packets dropped by the queue.

Active Notification requests for this parameter MAY be denied.

0 1.0
DroppedBytes unsignedInt R

Number of bytes dropped by the queue.

Active Notification requests for this parameter MAY be denied.

0 1.0
QueueOccupancyPackets unsignedInt R

Queue occupancy in packets (gives a measure of queue latency).

Active Notification requests for this parameter MAY be denied.

0 1.0
QueueOccupancyPercentage unsignedInt(0:100) R

Queue occupancy as a percentage, i.e. 100 * queue occupancy in bytes / queue size in bytes (gives a measure of queue usage).

Active Notification requests for this parameter MAY be denied.

0 1.0
InternetGatewayDevice.Capabilities. object R The capabilities of the device. This is a constant read-only object, meaning that only a firmware upgrade will cause these values to be altered. - 1.0
InternetGatewayDevice.Capabilities.PerformanceDiagnostic. object R The capabilities of the Performance Diagnostics (DownloadDiagnostics and UploadDiagnostics) for the device. - 1.0
DownloadTransports string[] R

Comma-separated list of strings. Supported DownloadDiagnostics transport protocols for a CPE device.

Each list item is an enumeration of:

  • HTTP
  • FTP (OPTIONAL)
- 1.0
UploadTransports string[] R

Comma-separated list of strings. Supported UploadDiagnostics transport protocols for a CPE device.

Each list item is an enumeration of:

  • HTTP
  • FTP (OPTIONAL)
- 1.0
InternetGatewayDevice.DownloadDiagnostics. object R This object defines the diagnostics configuration for a HTTP and FTP DownloadDiagnostics Test. Files received in the DownloadDiagnostics do not require file storage on the CPE device. - 1.0
DiagnosticsState string W

Indicate the availability of diagnostic data. Enumeration of:

  • None (READONLY)
  • Requested
  • Completed (READONLY)
  • Error_InitConnectionFailed (READONLY)
  • Error_NoResponse (READONLY)
  • Error_TransferFailed (READONLY)
  • Error_PasswordRequestFailed (READONLY)
  • Error_LoginFailed (READONLY)
  • Error_NoTransferMode (READONLY)
  • Error_NoPASV (READONLY)
  • Error_IncorrectSize (READONLY)
  • Error_Timeout (READONLY) If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Completed (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Completed, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code 8 DIAGNOSTICS COMPLETE in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None. Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None. While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None. While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

Active Notification requests for this parameter MAY be denied.

- 1.0
Interface string(:256) W The value MUST be the Path Name of the IP-layer interface over which the test is to be performed. The value of this parameter MUST be either a valid interface or an empty string. An attempt to set this parameter to a different value MUST be rejected as an invalid parameter value. If an empty string is specified, the CPE MUST use the default routing interface. - 1.0
DownloadURL string(:256) W The URL, as defined in [RFC3986], for the CPE to perform the download on. This parameter MUST be in the form of a valid HTTP [RFC2616] or FTP [RFC862] URL. When using FTP transport, FTP binary transfer MUST be used. When using HTTP transport, persistent connections MUST be used and pipelining MUST NOT be used. When using HTTP transport the HTTP Authentication MUST NOT be used. - 1.0
DSCP unsignedInt(0:63) W The DiffServ code point for marking packets transmitted in the test. The default value SHOULD be zero. - 1.0
EthernetPriority unsignedInt(0:7) W Ethernet priority code for marking packets transmitted in the test (if applicable). The default value SHOULD be zero. - 1.0
ROMTime dateTime R

Request time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

  • For HTTP this is the time at which the client sends the GET command.
  • For FTP this is the time at which the client sends the RTRV command.

Active Notification requests for this parameter MAY be denied.

- 1.0
BOMTime dateTime R

Begin of transmission time in UTC, which MUST be specified to microsecond precision For example: 2008-04-09T15:01:05.123456

  • For HTTP this is the time at which the first data packet is received.
  • For FTP this is the time at which the client receives the first data packet on the data connection.

Active Notification requests for this parameter MAY be denied.

- 1.0
EOMTime dateTime R

End of transmission in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

  • For HTTP this is the time at which the last data packet is received.
  • For FTP this is the time at which the client receives the last packet on the data connection.

Active Notification requests for this parameter MAY be denied.

- 1.0
TestBytesReceived unsignedInt R

The test traffic received in bytes during the FTP/HTTP transaction including FTP/HTTP headers, between BOMTime and EOMTime,

Active Notification requests for this parameter MAY be denied.

- 1.0
TotalBytesReceived unsignedInt R

The total number of bytes received on the Interface between BOMTime and EOMTime.

Active Notification requests for this parameter MAY be denied.

- 1.0
TCPOpenRequestTime dateTime R

Request time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

  • For HTTP this is the time at which the TCP socket open (SYN) was sent for the HTTP connection.
  • For FTP this is the time at which the TCP socket open (SYN) was sent for the data connection. Note: Interval of 1 microsecond SHOULD be supported.

Active Notification requests for this parameter MAY be denied.

- 1.0
TCPOpenResponseTime dateTime R

Response time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

  • For HTTP this is the time at which the TCP ACK to the socket opening the HTTP connection was received.
  • For FTP this is the time at which the TCP ACK to the socket opening the data connection was received. Note: Interval of 1 microsecond SHOULD be supported.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.UploadDiagnostics. object R This object defines the diagnostics configuration for a HTTP or FTP UploadDiagnostics test. Files sent by the UploadDiagnostics do not require file storage on the CPE device, and MAY be an arbitrary stream of bytes. - 1.0
DiagnosticsState string W

Indicate the availability of diagnostic data. Enumeration of:

  • None (READONLY)
  • Requested
  • Completed (READONLY)
  • Error_InitConnectionFailed (READONLY)
  • Error_NoResponse (READONLY)
  • Error_PasswordRequestFailed (READONLY)
  • Error_LoginFailed (READONLY)
  • Error_NoTransferMode (READONLY)
  • Error_NoPASV (READONLY)
  • Error_NoCWD (READONLY)
  • Error_NoSTOR (READONLY)
  • Error_NoTransferComplete (READONLY) If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Completed (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Completed, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code 8 DIAGNOSTICS COMPLETE in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None. Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None. While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None. While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

Active Notification requests for this parameter MAY be denied.

- 1.0
Interface string(:256) W The value MUST be the Path Name of the IP-layer interface over which the test is to be performed. The value of this parameter MUST be either a valid interface or an empty string. An attempt to set this parameter to a different value MUST be rejected as an invalid parameter value. If an empty string is specified, the CPE MUST use the default routing interface. - 1.0
UploadURL string(:256) W The URL, as defined in [RFC3986], for the CPE to Upload to. This parameter MUST be in the form of a valid HTTP [RFC2616] or FTP [RFC862] URL. When using FTP transport, FTP binary transfer MUST be used. When using HTTP transport, persistent connections MUST be used and pipelining MUST NOT be used. When using HTTP transport the HTTP Authentication MUST NOT be used. - 1.0
DSCP unsignedInt(0:63) W DiffServ code point for marking packets transmitted in the test. The default value SHOULD be zero. - 1.0
EthernetPriority unsignedInt(0:7) W Ethernet priority code for marking packets transmitted in the test (if applicable). The default value SHOULD be zero. - 1.0
TestFileLength unsignedInt W The size of the file (in bytes) to be uploaded to the server. The CPE MUST insure the appropriate number of bytes are sent. - 1.0
ROMTime dateTime R

Request time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

  • For HTTP this is the time at which the client sends the PUT command
  • For FTP this is the time at which the STOR command is sent.

Active Notification requests for this parameter MAY be denied.

- 1.0
BOMTime dateTime R

Begin of transmission time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

  • For HTTP this is the time at which the first data packet is sent.
  • For FTP this is the time at which the client receives the ready for transfer notification.

Active Notification requests for this parameter MAY be denied.

- 1.0
EOMTime dateTime R

End of transmission in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

  • For HTTP this is the time when the HTTP successful response code is received.
  • For FTP this is the time when the client receives a transfer complete.

Active Notification requests for this parameter MAY be denied.

- 1.0
TotalBytesSent unsignedInt R

The total number of bytes sent on the Interface between BOMTime and EOMTime.

Active Notification requests for this parameter MAY be denied.

- 1.0
TCPOpenRequestTime dateTime R

Request time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

  • For HTTP this is the time at which the TCP socket open (SYN) was sent for the HTTP connection.
  • For FTP this is the time at which the TCP socket open (SYN) was sent for the data connection Note: Interval of 1 microsecond SHOULD be supported.

Active Notification requests for this parameter MAY be denied.

- 1.0
TCPOpenResponseTime dateTime R

Response time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456

  • For HTTP this is the Time at which the TCP ACK to the socket opening the HTTP connection was received.
  • For FTP this is the Time at which the TCP ACK to the socket opening the Data connection was received. Note: Interval of 1 microsecond SHOULD be supported.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.UDPEchoConfig. object R This object allows the CPE to be configured to perform the UDP Echo Service defined in [RFC862] and UDP Echo Plus Service defined in [Appendix A.1/TR-143]. - 1.0
Enable boolean W MUST be enabled to receive UDP echo. When enabled from a disabled state all related timestamps, statistics and UDP Echo Plus counters are cleared. - 1.0
Interface string(:256) W The value MUST be the Path Name of IP-layer interface over which the CPE MUST listen and receive UDP echo requests on. The value of this parameter MUST be either a valid interface or an empty string. An attempt to set this parameter to a different value MUST be rejected as an invalid parameter value. If an empty string is specified, the CPE MUST listen and receive UDP echo requests on all interfaces. Note: Interfaces behind a NAT MAY require port forwarding rules configured in the Gateway to enable receiving the UDP packets. - 1.0
SourceIPAddress string(:45) W [IPAddress] The Source IP address of the UDP echo packet. The CPE MUST only respond to a UDP echo from this source IP address. - 1.0
UDPPort unsignedInt W The UDP port on which the UDP server MUST listen and respond to UDP echo requests. - 1.0
EchoPlusEnabled boolean W If true the CPE will perform necessary packet processing for UDP Echo Plus packets. - 1.0
EchoPlusSupported boolean R true if UDP Echo Plus is supported. - 1.0
PacketsReceived unsignedInt R

Incremented upon each valid UDP echo packet received.

Active Notification requests for this parameter MAY be denied.

- 1.0
PacketsResponded unsignedInt R

Incremented for each UDP echo response sent.

Active Notification requests for this parameter MAY be denied.

- 1.0
BytesReceived unsignedInt R

The number of UDP received bytes including payload and UDP header after the UDPEchoConfig is enabled.

Active Notification requests for this parameter MAY be denied.

- 1.0
BytesResponded unsignedInt R

The number of UDP responded bytes, including payload and UDP header sent after the UDPEchoConfig is enabled.

Active Notification requests for this parameter MAY be denied.

- 1.0
TimeFirstPacketReceived dateTime R

Time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456, The time that the server receives the first UDP echo packet after the UDPEchoConfig is enabled.

Active Notification requests for this parameter MAY be denied.

- 1.0
TimeLastPacketReceived dateTime R

Time in UTC, which MUST be specified to microsecond precision. For example: 2008-04-09T15:01:05.123456 The time that the server receives the most recent UDP echo packet.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.CaptivePortal. object R This object contains parameters relating to the captive portal configuration on the CPE. The captive portal configuration defines the CPE’s WAN-destined HTTP (port 80) traffic redirect behavior. When the captive portal is disabled, WAN-destined HTTP (port 80) traffic MUST be permitted to all destinations. When the captive portal is enabled, WAN-destined HTTP (port 80) traffic MUST be permitted only to destinations listed in the AllowedList; traffic to all other destinations MUST be redirected to the CaptivePortalURL. - 1.0
Enable boolean W Enables or disables the captive portal. - 1.0
Status string R

Indicates the status of the captive portal. Enumeration of:

  • Disabled
  • Enabled
  • Error_URLEmpty (CaptivePortalURL is an empty string)
  • Error (OPTIONAL) The Error value MAY be used by the CPE to indicate a locally defined error condition.
- 1.0
AllowedList string[](:10000) W Comma-separated list (maximum number of characters 10000) of strings. IP addresses to which HTTP (port 80) traffic MUST always be permitted, regardless of whether the captive portal is enabled. Each entry in the list MUST be either an IP address or an IP subnet specified using variable length subnet mask (VLSM) syntax. An IP subnet is specified as an IP address followed (with no intervening white space) by “/n”, where n is an integer in the range 0-32; this is equivalent to a subnet mask consisting of n 1s followed by 32 minus n 0s. For example, 1.2.3.4 specifies a single IP address, and 1.2.3.4/24 specifies a class C subnet with subnet mask 255.255.255.0. The maximum length of a single entry (plus comma) is 19 characters so 10000 bytes is sufficient for more than 500 IP addresses and/or IP subnets. - 1.0
CaptivePortalURL string(:2000) W Captive portal URL to which WAN-destined HTTP (port 80) traffic to destinations not listed in the AllowedList will be redirected. The captive portal URL MUST be an HTTP (not HTTPS) URL. The CPE MUST permit the captive portal URL to be set to an empty string, which has the effect of disabling the captive portal (if Enable is true and the captive portal URL is an empty string, Status MUST be Error_URLEmpty). - 1.0
InternetGatewayDevice.TraceRouteDiagnostics. object R This object is defines access to an IP-layer trace-route test for the specified IP interface. - 1.0
DiagnosticsState string W

Indicates availability of diagnostic data. Enumeration of:

  • None (READONLY)
  • Requested
  • Complete (READONLY)
  • Error_CannotResolveHostName (READONLY)
  • Error_MaxHopCountExceeded (READONLY) If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code 8 DIAGNOSTICS COMPLETE in the Inform message.

Active Notification requests for this parameter MAY be denied.

- 1.0
Interface string(:256) W The value MUST be the Path Name of the WAN or LAN IP-layer interface over which the test is to be performed. This identifies the source IP address to use when performing the test. The following is a WAN interface example: InternetGatewayDevice.WANDevice.1.WANConnectionDevice.2.WANPPPConnection.1 The following is a LAN interface example: InternetGatewayDevice.LANDevice.1.LANHostConfigManagement.IPInterface.1 - 1.0
Host string(:256) W Host name or address of the host to find a route to - 1.0
NumberOfTries unsignedInt(1:3) W Number of tries per hop. Set prior to running Diagnostic. By default, the CPE SHOULD set this value to 3. - 1.0
Timeout unsignedInt(1:) W Timeout in milliseconds for the trace route test. By default the CPE SHOULD set this value to 5000. - 1.0
DataBlockSize unsignedInt(1:65535) W Size of the data block in bytes to be sent for each trace route. By default, the CPE SHOULD set this value to 38. - 1.0
DSCP unsignedInt(0:63) W DiffServ codepoint to be used for the test packets. By default the CPE SHOULD set this value to 0. - 1.0
MaxHopCount unsignedInt(1:64) W The maximum number of hop used in outgoing probe packets (max TTL). By default the CPE SHOULD set this value to 30. - 1.0
ResponseTime unsignedInt R

Result parameter indicating the response time in milliseconds the most recent trace route test. If a route could not be determined, this value MUST be zero.

Active Notification requests for this parameter MAY be denied.

- 1.0
RouteHopsNumberOfEntries unsignedInt R

Number of entries in the RouteHops table.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.TraceRouteDiagnostics.RouteHops.{i}. object(0:) R Contains the array of results returned. If a route could not be determined, this array will be empty - 1.0
HopHost string(:256) R

Result parameter indicating the Host Name if DNS is able to resolve or IP Address of a hop along the discovered route.

Active Notification requests for this parameter MAY be denied.

- 1.0
HopHostAddress string R

If this parameter is not an empty string it will contain the last IP address of the host returned for this hop and the HopHost will contain the Host Name returned from the reverse DNS query.

Active Notification requests for this parameter MAY be denied.

- 1.0
HopErrorCode unsignedInt R

Contains the error code returned for this hop This code is directly from the ICMP CODE field.

Active Notification requests for this parameter MAY be denied.

- 1.0
HopRTTimes unsignedInt[](:16) R

Comma-separated list (maximum number of characters 16) of unsigned integers. Contains one or more round trip times in milliseconds (one for each repetition) for this hop.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.LANInterfaces. object R This object contains LAN-side layer 1/2 interfaces that are not currently connected to the Gateway’s IP router and which therefore do not currently reside within a LANDevice instance. - 1.0
LANEthernetInterfaceNumberOfEntries unsignedInt R Number of instances of LANEthernetInterfaceConfig in this object. - 1.0
LANUSBInterfaceNumberOfEntries unsignedInt R Number of instances of LANUSBInterfaceConfig in this object. - 1.0
LANWLANConfigurationNumberOfEntries unsignedInt R Number of instances of WLANConfiguration in this object object. - 1.0
InternetGatewayDevice.LANInterfaces.LANEthernetInterfaceConfig.{i}. object(0:) R This object models an Ethernet LAN connection on a CPE device. The object definition is identical to that for InternetGatewayDevice.LANDevice.{i}.LANEthernetInterfaceConfig.{i}. - 1.0
InternetGatewayDevice.LANInterfaces.LANUSBInterfaceConfig.{i}. object(0:) R This object models a USB LAN connection on a CPE device. The object definition is identical to that for InternetGatewayDevice.LANDevice.{i}.LANUSBInterfaceConfig.{i}. - 1.0
InternetGatewayDevice.LANInterfaces.WLANConfiguration.{i}. object(0:) R This object models an 802.11 LAN connection on a CPE device. The object definition is identical to that for InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}. - 1.0
InternetGatewayDevice.User.{i}. object(0:) W

This object contains parameters relating to the user characteristics.

At most one enabled entry in this table can exist with a given value for Username.

- 1.0
Enable boolean W Enables/disables this user object instance. If the User being configured is currently accessing the device then a disable MUST apply to the next user session and the current user session MUST NOT be abruptly terminated. false 1.0
RemoteAccessCapable boolean W Allows this user to remotely access the UserInterface via the mechanism defined in UserInterface.RemoteAccess. false 1.0
Username string(:64) W Name of the current user. MUST NOT be an empty string for an enabled entry. <Empty> 1.0
Password string(:64) W

The user’s password.

When read, this parameter returns an empty string, regardless of the actual value.

- 1.0
Language string(:16) W String describing the default language for the local configuration interface, specified according to [RFC3066]. If an empty string, UserInterface.CurrentLanguage is used. <Empty> 1.0
InternetGatewayDevice.UPnP. object R This object contains all UPnP related objects and parameters including Device and Discovery related objects and parameters. - 1.0
InternetGatewayDevice.UPnP.Device. object R Configuration Object for UPnP Access. - 1.0
Enable boolean W Enables/Disables UPnP support. - 1.0
UPnPMediaServer boolean W Enables/Disables UPnP Media Server. - 1.0
UPnPMediaRenderer boolean W Enables/Disables UPnP Media Renderer. - 1.0
UPnPWLANAccessPoint boolean W Enables/Disables UPnP Wireless Access Point. - 1.0
UPnPQoSDevice boolean W Enables/Disables UPnP QoS Device. - 1.0
UPnPQoSPolicyHolder boolean W Enables/Disables UPnP QoS Policy Holder. - 1.0
UPnPIGD boolean W Enables/Disables UPnP IGD. - 1.0
InternetGatewayDevice.UPnP.Device.Capabilities. object R This object defines what UPnP capabilities this device has. - 1.0
UPnPArchitecture unsignedInt R Numeric value indicating the version of supported architecture for UPnP. A value of 0 indicates no support. - 1.0
UPnPMediaServer unsignedInt R Numeric value indicating the supported revision for UPnP Media Server. A value of 0 indicates no support. - 1.0
UPnPMediaRenderer unsignedInt R Numeric value indicating the supported revision for UPnP Media Renderer. A value of 0 indicates no support. - 1.0
UPnPWLANAccessPoint unsignedInt R Numeric value indicating the supported revision for UPnP Wireless Access Point. A value of 0 indicates no support. - 1.0
UPnPBasicDevice unsignedInt R Numeric value indicating the supported revision for UPnP Basic Device. A value of 0 indicates no support. - 1.0
UPnPQoSDevice unsignedInt R Numeric value indicating the supported revision for UPnP Qos Device. A value of 0 indicates no support. - 1.0
UPnPQoSPolicyHolder unsignedInt R Numeric value indicating the supported revision for UPnP Qos Policy Holder. A value of 0 indicates no support. - 1.0
UPnPIGD unsignedInt R Numeric value indicating the supported revision for UPnP IGD. A value of 0 indicates no support. - 1.0
InternetGatewayDevice.UPnP.Discovery. object R UPnP [UPnP-DAv1] SSDP discovered root devices, embedded devices and embedded services. The CPE MAY, but need not, retain some or all of the information in this object across reboots. - 1.0
RootDeviceNumberOfEntries unsignedInt R Number of entries in RootDevice table. - 1.0
DeviceNumberOfEntries unsignedInt R Number of entries in Device table. - 1.0
ServiceNumberOfEntries unsignedInt R Number of entries in Service table. - 1.0
InternetGatewayDevice.UPnP.Discovery.RootDevice.{i}. object(0:) R

UPnP root device table. This table contains an entry for each UPnP root device that has been discovered via SSDP.

At most one entry in this table can exist with a given value for UUID.

- 1.0
Status string R

The status of the UPnP root device. Enumeration of:

  • LeaseActive (Device is active and UPnP lease has not expired)
  • LeaseExpired (Device is inactive because UPnP lease has expired)
  • ByebyeReceived (Device is inactive because byebye message was received) The ability to list inactive UPnP root devices is OPTIONAL. The length of time an inactive device remains listed in this table is a local matter to the CPE.
- 1.0
UUID string(:36) R

This UPnP root device’s UUID (Universally Unique IDentifier) [RFC4122], extracted from any of its USN (Unique Service Name) headers. This is a 36-byte string that uniquely identifies the device, the following is an example:

02c29d2a-dbfd-2d91-99c9-306d537e9856

Possible patterns:

  • [0-9A-Fa-f]{8}-([0-9A-Fa-f]{4}-){3}[0-9A-Fa-f]{12}
- 1.0
USN string(:256) R

The value of the USN (Unique Service Name) header for this UPnP root device. Three discovery messages are sent for root devices, and this SHOULD be the value of the USN header of the following form:

uuid:device-UUID::urn:domain-name:device:deviceType:v SSDP is an unreliable protocol and it is possible that no discovery message containing the USN header of the above form was ever received. If so, one of the other two forms MAY be used:
uuid:device-UUID::upnp:rootdevice
uuid:device-UUID (for root device UUID)
- 1.0
LeaseTime unsignedInt R The UPnP root device lease time in seconds, extracted from the CACHE-CONTROL header. - 1.0
Location string(:256) R The value of the LOCATION header for this UPnP root device, which is the URL of the root device’s DDD (Device Description Document). - 1.0
Server string(:256) R

The value of the SERVER header for this UPnP root device, which is a string of the following form:

OS/version UPnP/udaversion product/version where UPnP is a literal string, udaversion is the version of the UPnP Device Architecture.
- 1.0
Host string(:256)[](:1024) R Comma-separated list (maximum number of characters 1024) of strings (maximum number of characters per item 256). Indicates the full path names of all Host table entries, whether active or inactive, that correspond to this UPnP root device. As such entries are added to or removed from the Host tables, the value of this parameter MUST be updated accordingly. - 1.0
InternetGatewayDevice.UPnP.Discovery.Device.{i}. object(0:) R

UPnP embedded device table. This table contains an entry for each UPnP embedded device that has been discovered via SSDP.

At most one entry in this table can exist with a given value for UUID.

- 1.0
Status string R

The status of the UPnP embedded device. Enumeration of:

  • LeaseActive (Device is active and UPnP lease has not expired)
  • LeaseExpired (Device is inactive because UPnP lease has expired)
  • ByebyeReceived (Device is inactive because byebye message was received) The ability to list inactive UPnP embedded devices is OPTIONAL. The length of time an inactive device remains listed in this table is a local matter to the CPE.
- 1.0
UUID string(:36) R

This UPnP embedded device’s UUID (Universally Unique IDentifier) [RFC4122], extracted from any of its USN (Unique Service Name) headers. This is a 36-byte string that uniquely identifies the device, the following is an example:

02c29d2a-dbfd-2d91-99c9-306d537e9856

Possible patterns:

  • [0-9A-Fa-f]{8}-([0-9A-Fa-f]{4}-){3}[0-9A-Fa-f]{12}
- 1.0
USN string(:256) R

The value of the USN (Unique Service Name) header for this UPnP embedded device. Two discovery messages are sent for embedded devices, and this SHOULD be the value of the USN header of the following form:

uuid:device-UUID::urn:domain-name:device:deviceType:v SSDP is an unreliable protocol and it is possible that no discovery message containing the USN header of the above form was ever received. If so, the other form MAY be used:
uuid:device-UUID
- 1.0
LeaseTime unsignedInt R The UPnP embedded device lease time in seconds, extracted from the CACHE-CONTROL header. - 1.0
Location string(:256) R The value of the LOCATION header for this UPnP embedded device, which is the URL of the root device’s DDD (Device Description Document). - 1.0
Server string(:256) R

The value of the SERVER header for this UPnP embedded device, which is a string of the following form:

OS/version UPnP/udaversion product/version where UPnP is a literal string, udaversion is the version of the UPnP Device Architecture.
- 1.0
Host string(:256)[](:1024) R Comma-separated list (maximum number of characters 1024) of strings (maximum number of characters per item 256). Indicates the full path names of all Host table entries, whether active or inactive, that correspond to this UPnP embedded device. As such entries are added to or removed from the Host tables, the value of this parameter MUST be updated accordingly. - 1.0
InternetGatewayDevice.UPnP.Discovery.Service.{i}. object(0:) R

UPnP embedded service table. This table contains an entry for each UPnP embedded service that has been discovered via SSDP.

At most one entry in this table can exist with a given value for USN.

- 1.0
Status string R

The status of the UPnP embedded service. Enumeration of:

  • LeaseActive (Service is active and UPnP lease has not expired)
  • LeaseExpired (Service is inactive because UPnP lease has expired)
  • ByebyeReceived (Service is inactive because byebye message was received) The ability to list inactive UPnP embedded services is OPTIONAL. The length of time an inactive service remains listed in this table is a local matter to the CPE.
- 1.0
USN string(:256) R

The value of the USN (Unique Service Name) header for this UPnP embedded service. This is of the following form:

uuid:device-UUID::urn:domain-name:service:serviceType:v
- 1.0
LeaseTime unsignedInt R The UPnP embedded service lease time in seconds, extracted from the CACHE-CONTROL header. - 1.0
Location string(:256) R The value of the LOCATION header for this UPnP embedded service, which is the URL of the root device’s DDD (Device Description Document). - 1.0
Server string(:256) R

The value of the SERVER header for this UPnP embedded service, which is a string of the following form:

OS/version UPnP/udaversion product/version where UPnP is a literal string, udaversion is the version of the UPnP Device Architecture.
- 1.0
Host string(:256)[](:1024) R Comma-separated list (maximum number of characters 1024) of strings (maximum number of characters per item 256). Indicates the full path names of all Host table entries, whether active or inactive, that correspond to this UPnP embedded service. As such entries are added to or removed from the Host tables, the value of this parameter MUST be updated accordingly. - 1.0
InternetGatewayDevice.DLNA. object R This object contains all DLNA related objects and parameters. - 1.0
InternetGatewayDevice.DLNA.Capabilities. object R DLNA capabilities. - 1.0
HNDDeviceClass string[](:256) R Comma-separated list (maximum number of characters 256) of strings. Indicates the supported DLNA Home Network Device Classes [Table 4-1/DLNA-NDIG]. - 1.0
DeviceCapability string[](:256) R Comma-separated list (maximum number of characters 256) of strings. Indicates the supported DLNA Device Capabilities [Table 4-2/DLNA-NDIG]. - 1.0
HIDDeviceClass string[](:256) R Comma-separated list (maximum number of characters 256) of strings. Indicates the supported DLNA Home Infrastructure Device Classes [Table 4-4/DLNA-NDIG]. - 1.0
ImageClassProfileID string[](:256) R Comma-separated list (maximum number of characters 256) of strings. Indicates the DLNA Image Class Profile IDs supported by this device, from Tables 5-2 and 5-3 of [DLNA-NDIG]. - 1.0
AudioClassProfileID string[](:256) R Comma-separated list (maximum number of characters 256) of strings. Indicates the DLNA Audio Class Profile IDs supported by this device, from Tables 5-4 through 5-10 of [DLNA-NDIG]. - 1.0
AVClassProfileID string[](:256) R Comma-separated list (maximum number of characters 256) of strings. Indicates the DLNA AV Class Profile IDs supported by this device, from Tables 5-11 through 5-15 of [DLNA-NDIG]. - 1.0
MediaCollectionProfileID string[](:256) R Comma-separated list (maximum number of characters 256) of strings. Indicates the DLNA Media Collection Profile IDs supported by this device [Table 5-16/DLNA-NDIG]. - 1.0
PrinterClassProfileID string[](:256) R Comma-separated list (maximum number of characters 256) of strings. Indicates the DLNA Printer Class Profile IDs supported by this device [Table 5-17/DLNA-NDIG]. - 1.0
InternetGatewayDevice.SmartCardReader.{i}. object(0:) R

This object describes the characteristics of the smart card reader.

At most one entry in this table can exist with a given value for Name.

- 1.0
Enable boolean W Enables or disables this smart card reader. - 1.0
Status string R

Indicates the status of this smart card reader.

Enumeration of:

  • Disabled
  • Enabled (Indicates the smart card reader is enabled and functioning properly)
  • Error (Indicates the smart card reader is enabled and not functioning properly)
- 1.0
Name string(:256) R Human-readable name associated with this smart card reader. - 1.0
Reset boolean W

When set to true, resets the SmartCard Reader and the associated SmartCard.

When read, this parameter returns false, regardless of the actual value.

- 1.0
ResetTime dateTime R The time at which this SmartCard Reader was reset. Reset can be caused by:
  • Status transition from Disabled to Enabled
  • Reset set to true.
  • An internal reset of the SmartCard Reader (including a reboot of the device). Unknown Time value indicates that this SmartCard Reader has never been reset, which can only happen if it has never been enabled.
- 1.0
DecryptionFailedCounter unsignedInt R

Counter incremented once each time decryption cannot be carried out. This counter relates to the smart card reader, not to the smart card itself, i.e. it is reset when the Reset parameter is used and not when a Smart Card is inserted or removed.

Active Notification requests for this parameter MAY be denied.

- 1.0
DecryptionFailedNoKeyCounter unsignedInt R

Counter incremented once each time the key is not available to decrypt it. This is a subset of the more general DecryptionFailedCounter within the same object and thus will always be less than that parameter. This counter relates to the smart card reader, not to the smart card itself, i.e. it is reset when the Reset parameter is used and not when a Smart Card is inserted or removed.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.SmartCardReader.{i}.SmartCard. object R Status of currently associated smart card. - 1.0
Status string R

Status of the Smart Card.

Enumeration of:

  • None (Indicates that no Smart Card is inserted)
  • Running (Indicates a Smart Card is present and working normally)
  • Error (Indicates the Smart Card is present and in an error condition)
- 1.0
Type string R

Smart Card Type. Enumeration of:

  • CA
  • DRM
  • UICC Vendors can extend the enumerated values with vendor specific extensions, in which case the rules outlined in [Section 3.3/TR-106a2] MUST be adhered to.
- 1.0
Application string[] R

Comma-separated list of strings. Indicates Smart Card Application(s). Application is only relevant when Type has a value of UICC, otherwise it is an empty string. Each list item is an enumeration of:

  • SIM
  • USIM
  • ISIM Vendors can extend the enumerated values with vendor specific extensions, in which case the rules outlined in [Section 3.3/TR-106a2] MUST be adhered to.
- 1.0
SerialNumber string(:256) R The Smart Card Serial Number or an empty string if the Smart Card serial Number is not available, e.g. in the case of IPTV due to restrictions of the Service Delivery Platform. - 1.0
ATR string(:1024) R The Smart Card answer to a reset action. Issued by the Smart Card upon reset. - 1.0
InternetGatewayDevice.SelfTestDiagnostics. object R This diagnostics test is vendor-specific and MAY include testing hardware, software, and/or firmware. - 1.0
DiagnosticsState string W

Indicates availability of diagnostic data. Enumeration of:

  • None
  • Requested
  • Complete
  • Error_Internal
  • Error_Other If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Complete (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Complete, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code “8 DIAGNOSTICS COMPLETE” in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None. Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None. While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None. While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

Active Notification requests for this parameter MAY be denied.

- 1.0
Results string(:1024) R

Results of self-test (vendor specific).

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.NSLookupDiagnostics. object R This object defines access to an IP-layer NS Lookup test for the specified IP interface. When initiated, the NS Lookup test will contact DNSServer and look up HostName NumberOfRepetitions times. There will be a Result instance for each time the device performs a DNS lookup, which is determined by the value of NumberOfRepetitions. Any previous Result instances are removed when a new test is initiated. - 1.0
DiagnosticsState string W

Indicates availability of diagnostic data. Enumeration of:

  • None
  • Requested
  • Complete
  • Error_DNSServerNotResolved (Unable to resolve DNSServer Name)
  • Error_Internal
  • Error_Other If the ACS sets the value of this parameter to Requested, the CPE MUST initiate the corresponding diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic. When the test is completed, the value of this parameter MUST be either Complete (if the test completed successfully), or one of the Error values listed above. If the value of this parameter is anything other than Complete, the values of the results parameters for this test are indeterminate. When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code “8 DIAGNOSTICS COMPLETE” in the Inform message. After the diagnostic is complete, the value of all result parameters (all read-only parameters in this object) MUST be retained by the CPE until either this diagnostic is run again, or the CPE reboots. After a reboot, if the CPE has not retained the result parameters from the most recent test, it MUST set the value of this parameter to None. Modifying any of the writable parameters in this object except for this one MUST result in the value of this parameter being set to None. While the test is in progress, modifying any of the writable parameters in this object except for this one MUST result in the test being terminated and the value of this parameter being set to None. While the test is in progress, setting this parameter to Requested (and possibly modifying other writable parameters in this object) MUST result in the test being terminated and then restarted using the current values of the test parameters.

Active Notification requests for this parameter MAY be denied.

- 1.0
Interface string(:256) W The value MUST be the Path Name of a table row. This parameter specifies the IP-layer interface over which the test is to be performed (i.e. the source IP address to use when performing the test). If an empty string is specified, the CPE MUST use its routing policy (Forwarding table entries), if necessary, to determine the appropriate interface. - 1.0
HostName string(:256) W Specifies the Host Name that NS Lookup is to look for. The current domain name MUST be used unless the name is a fully qualified name. - 1.0
DNSServer string(:256) W Specifies the DNS Server name or IP address that NS Lookup is to use for the lookup. The name of this server will be resolved using the default DNS server unless an IP address is provided. If an empty string is specified, the device’s default DNS server will be used. - 1.0
Timeout unsignedInt W Timeout in milliseconds that indicates that a request has failed. - 1.0
NumberOfRepetitions unsignedInt W The number of times the device SHOULD repeat the execution of the NSLookup using the same input parameters. If the diagnostics test fails the CPE MAY terminate the test without completing the full number of repetitions. Each repetition will use a Result instance to hold the NSLookup result data. - 1.0
SuccessCount unsignedInt R

Number of successfully executed repetitions.

Active Notification requests for this parameter MAY be denied.

- 1.0
ResultNumberOfEntries unsignedInt R

Total number of Result entries from the most recent invocation of the test.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.NSLookupDiagnostics.Result.{i}. object(0:) R Results from the most recent invocation of the test, one instance per repetition. - 1.0
Status string R

Result Parameter to represent whether the NS Lookup was successful or not. Errors for individual Result instances do not get bubbled up to NSLookupDiagnostics.DiagnosticsState. A failure on a specific attempt does not mean that the overall test failed, but a failure on all attempts means that NSLookupDiagnostics.DiagnosticsState SHOULD be Error_Other.

Enumeration of:

  • Success
  • Error_DNSServerNotAvailable
  • Error_HostNameNotResolved
  • Error_Timeout
  • Error_Other

Active Notification requests for this parameter MAY be denied.

- 1.0
AnswerType string R

Result parameter to represent whether the answer is Authoritative or not.

Enumeration of:

  • None (Indicates that the NS Lookup failed to find the host)
  • Authoritative
  • NonAuthoritative

Active Notification requests for this parameter MAY be denied.

- 1.0
HostNameReturned string(:256) R

Result parameter to represent the fully qualified name for the Host Name in the calling parameter (e.g. HostName.DomainName); if no response was provided, then this parameter is an empty string.

Active Notification requests for this parameter MAY be denied.

- 1.0
IPAddresses string(:45)[:10] R

[IPAddress] Comma-separated list (up to 10 items) of IP Addresses. Indicates the IP Address results returned by the NS Lookup; if no response was provided, then this parameter is an empty string.

Active Notification requests for this parameter MAY be denied.

- 1.0
DNSServerIP string(:45) R

[IPAddress] Result parameter to represent the actual DNS Server IP address that the NS Lookup used.

Active Notification requests for this parameter MAY be denied.

- 1.0
ResponseTime unsignedInt R

Response time (for the first response packet) in milliseconds, or 0 if no response was received.

Active Notification requests for this parameter MAY be denied.

- 1.0
InternetGatewayDevice.Firewall. object R Firewall configuration object. - 1.0
Config string W

How this firewall is configured. Enumeration of:

  • High (The firewall implements the “Traffic Denied Inbound” and “Minimally Permit Common Services Outbound” components of the ICSA residential certification’s Required Services Security Policy [ICSA-Firewall])
  • Low (All Outbound traffic and pinhole-defined Inbound traffic is allowed)
  • Off (All Inbound and Outbound traffic is allowed, and the CPE is only protected by NAT settings) Vendors can extend the enumerated values with vendor specific extensions, in which case the rules outlined in [Section 3.3/TR-106a2] MUST be adhered to.
- 1.0
Version string(:16) R A string identifying the firewall settings version currently used in the CPE, or an empty string if the firewall settings are not associated with a version. - 1.0
LastChange dateTime R The time at which the firewall settings most recently changed. - 1.0
InternetGatewayDevice.USBHosts. object R This object models the CPE’s USB Host controllers. See [Appendix I/TR-157] for Theory of Operation. - 1.0
HostNumberOfEntries unsignedInt R Number of entries in the Host table. - 1.0
InternetGatewayDevice.USBHosts.Host.{i}. object(0:) R

Table of CPE USB Host controllers.

At most one entry in this table can exist with a given value for Name.

- 1.0
Enable boolean W Enables or disables the USB Host controller. - 1.0
Name string(:64) R User-readable host controller name. - 1.0
Type string R

Type of USB Host

Enumeration of:

  • OHCI (Open Host Controller Interface)
  • EHCI (Enhanced Host Controller Interface)
  • UHCI (Universal Host Controller Interface)
  • xHCI (Extensible Host Controller Interface)
- 1.0
Reset boolean W

When set to true, reset the Host Controller and apply the reset signaling (see [Chapter 7.1.7.5/USB2.0]) to all of the Host Controller Hub downstream ports. The value is not saved in the device’s state and setting it to false has no effect.

When read, this parameter returns false, regardless of the actual value.

- 1.0
PowerManagementEnable boolean W When set to true, PowerManagementEnable enables the Host Controller to invoke Power Management policy, i.e. controlled Suspend (see [USB2.0], Chapters 4.3.2, 7.1.7.6, and 11.9). When set to false PowerManagementEnable immediately disables the Host controller Power Management policy. - 1.0
USBVersion string(:4) R USB specification version with which the controller complies. Example: “1.1” - 1.0
DeviceNumberOfEntries unsignedInt R Number of entries in the Device table. - 1.0
InternetGatewayDevice.USBHosts.Host.{i}.Device.{i}. object(0:) R

Table of connected USB devices.

At most one entry in this table can exist with a given value for DeviceNumber.

- 1.0
DeviceNumber unsignedInt R Device number on USB bus. - 1.0
USBVersion string(:4) R USB specification version with which the device complies. Example: “1.1” - 1.0
DeviceClass hexBinary(:1) R Class Code as assigned by USB-IF. When 0x00, each device specifies its own class code. When 0xFF, the class code is vendor specified. - 1.0
DeviceSubClass hexBinary(:1) R Subclass code (assigned by USB-IF). - 1.0
DeviceVersion unsignedInt(:65535) R Device release number. - 1.0
DeviceProtocol hexBinary(:1) R Protocol code (assigned by USB-IF). - 1.0
ProductID unsignedInt(:65535) R Product ID (assigned by manufacturer). - 1.0
VendorID unsignedInt(:65535) R Vendor ID (assigned by USB-IF). - 1.0
Manufacturer string(:64) R Device Manufacturer string descriptor. - 1.0
ProductClass string(:64) R Device Product Class string descriptor. - 1.0
SerialNumber string(:64) R Device SerialNumber string descriptor. - 1.0
Port unsignedInt(:255) R Hub port on parent device. 0 when no parent. - 1.0
Rate string R

Speed of the USB device. Enumeration of:

  • Low (1.5 Mbits/sec (187.5 KB/sec) defined in [USB1.0])
  • Full (12 Mbits/sec (1.5 MB/sec) defined in [USB1.0])
  • High (480 Mbits/sec (60 MB/sec) defined in [USB2.0])
  • Super (5.0 Gbits/sec (625 MB/sec) defined in [USB3.0]) Internal signaling between the connected USB device and the USB Host Controller provide the information needed to determine the negotiated rate.
- 1.0
Parent string R

The value MUST be the Path Name of a row in the USBHosts.Host.{i}.Device.{i}. table. If the referenced object is deleted, the parameter value MUST be set to an empty string. This is a reference to the parent USB device (e.g. hub device). Example:

.USBHosts.Host.2.Device.3 This is an empty string for a device connected to the Host controller (root hub).
- 1.0
MaxChildren unsignedInt R Number of ports. Only applies for hub device, equal to 0 for other devices. - 1.0
IsSuspended boolean R When true the associated Device is in a suspended (i.e. low-power) state (see [Chapter 11.9/USB2.0]). When false the associated Device is in any of the other states specified by the USB 2.0 Device State Machine (see [Chapter 9.1.1/USB2.0]). - 1.0
IsSelfPowered boolean R When true the associated device is at least partly powered by a local source (see [Chapter 9.4.5/USB2.0]). When false the associated device draws all the current it needs from the USB bus. - 1.0
ConfigurationNumberOfEntries unsignedInt R Number of entries in the Configuration table. - 1.0
InternetGatewayDevice.USBHosts.Host.{i}.Device.{i}.Configuration.{i}. object(0:) R

Table of device configurations.

At most one entry in this table can exist with a given value for ConfigurationNumber.

- 1.0
ConfigurationNumber unsignedInt R The identifier for each Device Configuration. - 1.0
InterfaceNumberOfEntries unsignedInt R Number of entries in the Interface table. - 1.0
InternetGatewayDevice.USBHosts.Host.{i}.Device.{i}.Configuration.{i}.Interface.{i}. object(0:) R

Table of device interface descriptors.

At most one entry in this table can exist with a given value for InterfaceNumber.

- 1.0
InterfaceNumber unsignedInt(:255) R Number of this interface (from USB interface descriptor). - 1.0
InterfaceClass hexBinary(:1) R Class Code as assigned by USB-IF. When 0x00, each interface specifies its own class code. When 0xFF, the class code is vendor specified. - 1.0
InterfaceSubClass hexBinary(:1) R Subclass code (assigned by USB-IF). - 1.0
InterfaceProtocol hexBinary(:1) R Protocol code (assigned by USB-IF). - 1.0
InternetGatewayDevice.PeriodicStatistics. object R This object configures collection of periodic statistics for the device. Periodic statistics are measured over a sample interval (which can be aligned with absolute time) and are made available to the ACS as a comma-separated list of the most recent samples. This object provides a single set of global settings that affect the entire device unless overridden locally. - 1.0
MinSampleInterval unsignedInt R Minimum sample interval in seconds that the CPE is able to support. A value of 0 indicates no specific minimum sample interval. - 1.0
MaxReportSamples unsignedInt R Maximum number of samples of each statistic that the CPE is able to store and report. A value of 0 indicates no specific maximum number of samples. - 1.0
SampleSetNumberOfEntries unsignedInt R Number of entries in SampleSet table. - 1.0
InternetGatewayDevice.PeriodicStatistics.SampleSet.{i}. object(0:) W

Periodic statistics sample set table. Each sample set has its own sample interval etc.

At most one enabled entry in this table can exist with a given value for Name.

- 1.0
Enable boolean W Enables or disables collection of periodic statistics for this sample set. When collection of periodic statistics is enabled, any stored samples are discarded, and the first sample interval begins immediately. false 1.0
Status string R

Indicates availability of Sample statistics. Enumeration of:

  • Disabled (Collection is disabled)
  • Enabled (Collection is enabled)
  • Trigger (Collection is enabled and the ACS SHOULD now fetch the collected data) The Trigger value is only used for triggering the ACS to fetch the collected data and can only be used when FetchSamples is in the range [1:ReportSamples]. The transition from Enabled to Trigger to Enabled MUST be instantaneous and so will result in only a single value change for notification purposes.
Disabled 1.0
Name string(:128) W The name of this sample set, which uniquely distinguishes each sample set. <Empty> 1.0
SampleInterval unsignedInt(1:) W The sample interval in seconds. Each statistic is measured over this sample interval. The CPE MAY reject a request to set SampleInterval to less than PeriodicStatistics.MinSampleInterval. Sample intervals MUST begin every SampleInterval seconds, with no delay between samples. If SampleInterval is changed while collection of periodic statistics is enabled, any stored samples are discarded, and the first sample interval begins immediately. For example, if ReportSamples is 24 and SampleInterval is 3600 (an hour), the CPE can store up to a day’s worth of samples for each statistic. 3600 1.0
ReportSamples unsignedInt(1:) W The number of samples that the CPE will store and report for each statistic. The CPE MUST permit ReportSamples to be set to at least PeriodicStatistics.MaxReportSamples. If ReportSamples is changed while collection of periodic statistics is enabled, the CPE will truncate or extend its statistics buffers as appropriate, but statistics collection MUST NOT otherwise be affected. For example, if ReportSamples is 24 and SampleInterval is 3600 (an hour), the CPE can store up to a day’s worth of samples for each statistic. 24 1.0
TimeReference dateTime W An absolute time reference in UTC to determine when sample intervals will complete. Each sample interval MUST complete at this reference time plus or minus an integer multiple of SampleInterval. TimeReference is used only to set the “phase” of the sample and fetch intervals. The actual value of TimeReference can be arbitrarily far into the past or future. This time reference also determines when the Status Enabled to Trigger to Enabled transitions that are controlled by FetchSamples will occur. If collection of periodic statistics is enabled and FetchSamples is in the range [1:ReportSamples] then each such Status transition MUST occur at this reference time plus or minus an integer multiple of FetchSamples * SampleInterval (the fetch interval). If TimeReference is changed while collection of periodic statistics is enabled, any stored samples are discarded, and the first sample interval begins immediately. The Unknown Time value defined in [TR-106a2] indicates that no particular time reference is specified. That is, the CPE MAY locally choose the time reference, and is required only to adhere to the specified sample and fetch intervals. If absolute time is not available to the CPE, its sample and fetch interval behavior MUST be the same as if the TimeReference parameter was set to the Unknown Time value. For example, if SampleInterval is 3600 (an hour) and if TimeReference is set to UTC midnight on some day (in the past, present, or future) then sample intervals will complete on each UTC hour (00:00, 01:00, 02:00 etc). If, in addition, FetchSamples is 24, then the fetch interval is 86400 (a day) and Status Enabled to Trigger to Enabled transitions will occur every day at UTC midnight. Note that, if TimeReference is set to a time other than the Unknown Time, the first sample interval (which has to begin immediately) will almost certainly be shorter than SampleInterval). This is why TimeReference is defined in terms of when sample intervals complete rather than start. 0001-01-01T00:00:00Z 1.0
FetchSamples unsignedInt W The number of sample intervals to be collected before transitioning Status from Enabled to Trigger to Enabled. If this SampleSet is enabled and FetchSamples is in the range [1:ReportSamples] then Status MUST transition from Enabled to Trigger to Enabled on completion of every FetchSamples sample intervals. Otherwise, the transition MUST NOT occur. For example, if ReportSamples is 25 and FetchSamples is 24, then the CPE will store 25 values for each monitored parameter and the above Status transition will occur as the CPE stores each 24th of 25 sample intervals, which means that the ACS could delay for up to two sample intervals before reading the stored values and would still not miss any samples (see also ForceSample). To disable this trigger mechanism and still collect sampled statistics, FetchSamples can be set to either 0 or a value greater than ReportSamples. 0 1.0
ForceSample boolean W When set to true, forces statistics for the current sample to be calculated and updated in the data model. Setting it to false has no effect. When read, this parameter returns false, regardless of the actual value. If this is the first time that ForceSample has been set to true during the current sample interval, this MUST cause a new value to be added to each of the periodic statistics comma-separated list parameters, and the ReportEndTime and all SampleSeconds parameters MUST be updated accordingly. If this is not the first time that ForceSample has been set to true during the current sample interval, then the new values that were added as described in the previous paragraph, and the ReportEndTime and all SampleSeconds parameters, MUST be updated accordingly. Note that ForceSample just provides a “sneak preview” of the current sample. It does not create a new sample and it does not interfere with the sample interval schedule. At the end of each sample interval, if ForceSample was set to true during the sample interval then the new values that were added as described above, and the ReportEndTime and all SampleSeconds parameters, will be updated accordingly. In other words, the partial sample data that was created when ForceSample was set to true will be updated one last time at the end of the sample interval. false 1.0
ReportStartTime dateTime R The absolute time at which the sample interval for the first stored sample (for each statistic) started. <Empty> 1.0
ReportEndTime dateTime R The absolute time at which the sample interval for the last stored sample (for each statistic) ended. If ForceSample has been used to force statistics for the current sample to be calculated and updated in the data model, then ReportEndTime MUST be updated to reflect the actual time over which stored data was collected. <Empty> 1.0
SampleSeconds unsignedInt[] R

Comma-separated list of unsigned integers. Each entry indicates the number of seconds during which data was collected during the sample interval. Individual SampleSeconds values can be less than SampleInterval, for several reasons, including:

TimeReference has been set to a time other than the Unknown Time and the current sample interval started part of the way through a scheduled sample interval.
ForceSample has been used to force statistics for the current sample to be calculated and updated in the data model.

Active Notification requests for this parameter MAY be denied.

<Empty> 1.0
ParameterNumberOfEntries unsignedInt R Number of entries in Parameter table. 0 1.0
InternetGatewayDevice.PeriodicStatistics.SampleSet.{i}.Parameter.{i}. object(0:) W

Periodic statistics parameter table for this sample set. This table contains entries for parameters whose values are to be sampled. Note that the comma-separated lists in this object (SampleSeconds, SuspectData and Values) only ever change (a) when first enabled, (b) when ForceSample is set to true (a “sneak preview” of the current sample), or (c) at the end of the sample interval.

At most one enabled entry in this table can exist with a given value for Reference.

- 1.0
Enable boolean W Enables or disables this object instance. false 1.0
Reference string(:256) W The value MUST be the Path Name of a parameter. This is the parameter being monitored by the Periodic Statistics mechanism. <Empty> 1.0
SampleMode string W

Controls how this parameter’s value is sampled. Enumeration of:

  • Current (Sampled value is current value)
  • Change (Sampled value is change in value since start of sample interval) Parameters of non-numeric types can only support Current. The value of the SampleMode MUST be ignored for such parameters.
Current 1.0
CalculationMode string W

Controls how this parameter’s statistic is calculated from the sampled value(s). Enumeration of:

  • Latest (Statistic is sampled value at end of sample interval)
  • Minimum (Statistic is minimum sampled value during sample interval)
  • Maximum (Statistic is maximum sampled value during sample interval)
  • Average (Statistic is average (mean) sampled value during sample interval) Parameters of non-numeric types can only support Latest. The value of the CalculationMode MUST be ignored for such parameters. SampleMode MUST be applied before CalculationMode, i.e. the inputs to the calculation will have already accounted for SampleMode.
Latest 1.0
LowThreshold int W The low threshold value that controls the calculation of Failures. A value equal to HighThreshold disables the threshold/failure mechanism. Parameters of non-numeric types cannot support the threshold/failure mechanism. The value of this parameter MUST be ignored for such parameters. 0 1.0
HighThreshold int W The high threshold value that controls the calculation of Failures. A value equal to LowThreshold disables the threshold/failure mechanism. Parameters of non-numeric types cannot support the threshold/failure mechanism. The value of this parameter MUST be ignored for such parameters. 0 1.0
SampleSeconds unsignedInt[] R

Comma-separated list of unsigned integers. Each entry indicates the number of seconds during which data was collected for this parameter during the sample interval. Individual SampleSeconds values can be less than PeriodicStatistics.SampleSet.{i}.SampleInterval, for several reasons, including:

Any of the reasons for which PeriodicStatistics.SampleSet.{i}.SampleSeconds values might be less than PeriodicStatistics.SampleSet.{i}.SampleInterval.
The parameter doesn’t exist, or was created or deleted during a sample interval.

Active Notification requests for this parameter MAY be denied.

<Empty> 1.0
SuspectData unsignedInt(:1)[] R

Comma-separated list of unsigned integers (up to 1). Each entry is 0 if the sampled value is believed to be valid, or 1 if an event that might affect the validity of the sampled value occurred during the sample interval. For example, if the parameter value were to be reset during the sample interval then it would be appropriate to set SuspectData to 1.

Active Notification requests for this parameter MAY be denied.

<Empty> 1.0
Values string[] R

Comma-separated list of strings. Each entry indicates the value of the referenced parameter, as determined by SampleMode, during the sample interval. The statistics values in this comma-separated lists MUST be in time order, with the oldest one first and the most recent one last. If the SampleMode parameter is not present, or is inappropriate for the referenced parameter, the statistics values MUST be collected in Current mode.

Active Notification requests for this parameter MAY be denied.

<Empty> 1.0
Failures unsignedInt R Counts the number of times (since this object instance was last enabled) that a newly-calculated sample value (accounting for SampleMode) transitioned from the “in range” state to the “out of range” state, or between the “out of range (low)” and “out of range (high)” states. The states are defined as follows:
  • “in range” : current value is greater than LowThreshold and less than HighThreshold.
  • “out of range” : current value is less than or equal to LowThreshold, or greater than or equal to HighThreshold.
  • “out of range (low)” : current value is less than or equal to LowThreshold.
  • “out of range (high)” : current value is greater than or equal to HighThreshold. Note that, if LowThreshold and HighThreshold are both the same, the threshold/failure mechanism is disabled, so the value of this parameter will not increment. This parameter can be incremented at any time during a sample interval, and might be incremented more than once during a single sample interval. For this reason, the CPE SHOULD place a locally specified limit on the frequency at which it will notify the ACS of such changes, as described in [Section 3.2.1/TR-069a2]. Parameters of non-numeric types cannot support the threshold/failure mechanism. The value of this parameter MUST be ignored for such parameters.
0 1.0
InternetGatewayDevice.DownloadAvailability. object R This object contains multicast announcement and query parameters used for the purpose of downloading files. - 1.0
InternetGatewayDevice.DownloadAvailability.Announcement. object R This object contains multicast announcement parameters used to download files. - 1.0
Enable boolean W Enable/disable CPE ability to receive and use multicast announcements from a server for the purpose of downloading files. - 1.0
Status string R

The status of the announcement service.

Enumeration of:

  • Disabled
  • Enabled
  • Error (MAY be used by the CPE to indicate a locally defined error condition, OPTIONAL)
- 1.0
GroupNumberOfEntries unsignedInt R Number of entries in the Group table. - 1.0
InternetGatewayDevice.DownloadAvailability.Announcement.Group.{i}. object(0:) W

Multicast groups to which the CPE SHOULD listen for announcements.

At most one enabled entry in this table can exist with a given value for URL.

- 1.0
Enable boolean W Enable/disable listening to this multicast group. false 1.0
Status string R

The status of this group table entry.

Enumeration of:

  • Disabled
  • Enabled
  • Error (MAY be used by the CPE to indicate a locally defined error condition, e.g. unable to parse received announcements, OPTIONAL)
Disabled 1.0
URL string(:256) W URL [RFC3986] encoding the group address, source and port on which to listen, and other protocol information, e.g. expected announcement format. Depending on the application, the messages identified by this URL MAY directly contain the data to be downloaded, or alternatively MAY contain information informing the CPE how to obtain the data to be downloaded via a separate mechanism, which itself could involve a unicast or a multicast download protocol. Refer to [DVB-TS.102.824] for an example of a URL format that identifies a SAP [RFC2974] stream that indicates how to use either FLUTE [RFC3926] or DSM-CC [ISO-13818-6:1998] to perform the download. <Empty> 1.0
InternetGatewayDevice.DownloadAvailability.Query. object R This object contains multicast query parameters used to download files. - 1.0
Enable boolean W Enable/disable CPE ability to autonomously query a server for the purpose of downloading files. - 1.0
Status string R

The status of the query service.

Enumeration of:

  • Disabled
  • Enabled
  • Error (MAY be used by the CPE to indicate a locally defined error condition, e.g. unable to contact query response server, OPTIONAL)
- 1.0
URL string(:256) W URL [RFC3986] of the query response server. Depending on the application, the protocol described by this URL MAY be a SOAP interface, or MAY be any other RPC mechanism. Refer to [DVB-TS.102.824] for an example of a URL format that identifies a SOAP interface running over HTTP or HTTPS. - 1.0

Inform and Notification Requirements

Forced Inform Parameters

Parameter
InternetGatewayDevice.DeviceSummary
InternetGatewayDevice.DeviceInfo.HardwareVersion
InternetGatewayDevice.DeviceInfo.SoftwareVersion
InternetGatewayDevice.DeviceInfo.SpecVersion
InternetGatewayDevice.DeviceInfo.ProvisioningCode
InternetGatewayDevice.ManagementServer.ParameterKey
InternetGatewayDevice.ManagementServer.ConnectionRequestURL

Forced Active Notification Parameters

Parameter
InternetGatewayDevice.DeviceInfo.SoftwareVersion
InternetGatewayDevice.DeviceInfo.ProvisioningCode

Default Active Notification Parameters

Parameter
InternetGatewayDevice.ManagementServer.ConnectionRequestURL

Parameters for which Active Notification MAY be Denied

Parameter
InternetGatewayDevice.DeviceInfo.
UpTime
DeviceLog
InternetGatewayDevice.ManagementServer.
ParameterKey
InternetGatewayDevice.Time.
CurrentLocalTime
InternetGatewayDevice.IPPingDiagnostics.
DiagnosticsState
SuccessCount
FailureCount
AverageResponseTime
MaximumResponseTime
MinimumResponseTime
InternetGatewayDevice.LANDevice.{i}.LANEthernetInterfaceConfig.{i}.Stats.
BytesSent
BytesReceived
PacketsSent
PacketsReceived
ErrorsSent
ErrorsReceived
UnicastPacketsSent
UnicastPacketsReceived
DiscardPacketsSent
DiscardPacketsReceived
MulticastPacketsSent
MulticastPacketsReceived
BroadcastPacketsSent
BroadcastPacketsReceived
UnknownProtoPacketsReceived
InternetGatewayDevice.LANDevice.{i}.LANUSBInterfaceConfig.{i}.Stats.
BytesSent
BytesReceived
CellsSent
CellsReceived
ErrorsSent
ErrorsReceived
UnicastPacketsSent
UnicastPacketsReceived
DiscardPacketsSent
DiscardPacketsReceived
MulticastPacketsSent
MulticastPacketsReceived
BroadcastPacketsSent
BroadcastPacketsReceived
UnknownProtoPacketsReceived
InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.
TotalPSKFailures
TotalIntegrityFailures
ChannelsInUse
TotalBytesSent
TotalBytesReceived
TotalPacketsSent
TotalPacketsReceived
TotalAssociations
InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.AssociatedDevice.{i}.
AssociatedDeviceMACAddress
AssociatedDeviceIPAddress
AssociatedDeviceAuthenticationState
LastRequestedUnicastCipher
LastRequestedMulticastCipher
LastPMKId
LastDataTransmitRate
InternetGatewayDevice.LANDevice.{i}.Hosts.Host.{i}.
LeaseTimeRemaining
InternetGatewayDevice.WANDevice.{i}.WANCommonInterfaceConfig.
TotalBytesSent
TotalBytesReceived
TotalPacketsSent
TotalPacketsReceived
MaximumActiveConnections
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.
UpstreamCurrRate
DownstreamCurrRate
UpstreamMaxRate
DownstreamMaxRate
UpstreamNoiseMargin
DownstreamNoiseMargin
UpstreamAttenuation
DownstreamAttenuation
UpstreamPower
DownstreamPower
TotalStart
ShowtimeStart
LastShowtimeStart
CurrentDayStart
QuarterHourStart
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.Stats.Total.
ReceiveBlocks
TransmitBlocks
CellDelin
LinkRetrain
InitErrors
InitTimeouts
LossOfFraming
ErroredSecs
SeverelyErroredSecs
FECErrors
ATUCFECErrors
HECErrors
ATUCHECErrors
CRCErrors
ATUCCRCErrors
LInit
LOF
ATUCErroredSecs
ATUCSeverelyErroredSecs
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.Stats.Showtime.
ReceiveBlocks
TransmitBlocks
CellDelin
LinkRetrain
InitErrors
InitTimeouts
LossOfFraming
ErroredSecs
SeverelyErroredSecs
FECErrors
ATUCFECErrors
HECErrors
ATUCHECErrors
CRCErrors
ATUCCRCErrors
LInit
LOF
ATUCErroredSecs
ATUCSeverelyErroredSecs
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.Stats.LastShowtime.
ReceiveBlocks
TransmitBlocks
CellDelin
LinkRetrain
InitErrors
InitTimeouts
LossOfFraming
ErroredSecs
SeverelyErroredSecs
FECErrors
ATUCFECErrors
HECErrors
ATUCHECErrors
CRCErrors
ATUCCRCErrors
LInit
LOF
ATUCErroredSecs
ATUCSeverelyErroredSecs
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.Stats.CurrentDay.
ReceiveBlocks
TransmitBlocks
CellDelin
LinkRetrain
InitErrors
InitTimeouts
LossOfFraming
ErroredSecs
SeverelyErroredSecs
FECErrors
ATUCFECErrors
HECErrors
ATUCHECErrors
CRCErrors
ATUCCRCErrors
LInit
LOF
ATUCErroredSecs
ATUCSeverelyErroredSecs
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.Stats.QuarterHour.
ReceiveBlocks
TransmitBlocks
CellDelin
LinkRetrain
InitErrors
InitTimeouts
LossOfFraming
ErroredSecs
SeverelyErroredSecs
FECErrors
ATUCFECErrors
HECErrors
ATUCHECErrors
CRCErrors
ATUCCRCErrors
LInit
LOF
ATUCErroredSecs
ATUCSeverelyErroredSecs
InternetGatewayDevice.WANDevice.{i}.WANEthernetInterfaceConfig.Stats.
BytesSent
BytesReceived
PacketsSent
PacketsReceived
InternetGatewayDevice.WANDevice.{i}.WANDSLDiagnostics.
LoopDiagnosticsState
ACTPSDds
ACTPSDus
ACTATPds
ACTATPus
HLINSCds
HLINpsds
QLNpsds
SNRpsds
BITSpsds
GAINSpsds
HLINSCus
HLINGds
HLINGus
HLOGGds
HLOGGus
HLOGpsds
HLOGpsus
HLOGMTds
HLOGMTus
LATNpbds
LATNpbus
SATNds
SATNus
HLINpsus
QLNGds
QLNGus
QLNpsus
QLNMTds
QLNMTus
SNRGds
SNRGus
SNRpsus
SNRMTds
SNRMTus
BITSpsus
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANDSLLinkConfig.
ATMTransmittedBlocks
ATMReceivedBlocks
AAL5CRCErrors
ATMCRCErrors
ATMHECErrors
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANATMF5LoopbackDiagnostics.
DiagnosticsState
SuccessCount
FailureCount
AverageResponseTime
MinimumResponseTime
MaximumResponseTime
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.
Uptime
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.PortMapping.{i}.
PortMappingLeaseDuration
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANIPConnection.{i}.Stats.
EthernetBytesSent
EthernetBytesReceived
EthernetPacketsSent
EthernetPacketsReceived
EthernetErrorsSent
EthernetErrorsReceived
EthernetUnicastPacketsSent
EthernetUnicastPacketsReceived
EthernetDiscardPacketsSent
EthernetDiscardPacketsReceived
EthernetMulticastPacketsSent
EthernetMulticastPacketsReceived
EthernetBroadcastPacketsSent
EthernetBroadcastPacketsReceived
EthernetUnknownProtoPacketsReceived
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANPPPConnection.{i}.
Uptime
CurrentMRUSize
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANPPPConnection.{i}.PortMapping.{i}.
PortMappingLeaseDuration
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANPPPConnection.{i}.Stats.
EthernetBytesSent
EthernetBytesReceived
EthernetPacketsSent
EthernetPacketsReceived
EthernetErrorsSent
EthernetErrorsReceived
EthernetUnicastPacketsSent
EthernetUnicastPacketsReceived
EthernetDiscardPacketsSent
EthernetDiscardPacketsReceived
EthernetMulticastPacketsSent
EthernetMulticastPacketsReceived
EthernetBroadcastPacketsSent
EthernetBroadcastPacketsReceived
EthernetUnknownProtoPacketsReceived
InternetGatewayDevice.Layer2Bridging.
MaxBridgeEntries
MaxFilterEntries
MaxMarkingEntries
InternetGatewayDevice.Layer2Bridging.AvailableInterface.{i}.
AvailableInterfaceKey
InterfaceType
InterfaceReference
InternetGatewayDevice.QueueManagement.
MaxQueues
MaxClassificationEntries
MaxAppEntries
MaxFlowEntries
MaxPolicerEntries
MaxQueueEntries
InternetGatewayDevice.QueueManagement.Policer.{i}.
PossibleMeterTypes
CountedPackets
CountedBytes
TotalCountedPackets
TotalCountedBytes
ConformingCountedPackets
ConformingCountedBytes
PartiallyConformingCountedPackets
PartiallyConformingCountedBytes
NonConformingCountedPackets
NonConformingCountedBytes
InternetGatewayDevice.ManagementServer.ManageableDevice.{i}.
ManufacturerOUI
SerialNumber
ProductClass
InternetGatewayDevice.DownloadDiagnostics.
DiagnosticsState
ROMTime
BOMTime
EOMTime
TestBytesReceived
TotalBytesReceived
TCPOpenRequestTime
TCPOpenResponseTime
InternetGatewayDevice.UploadDiagnostics.
DiagnosticsState
ROMTime
BOMTime
EOMTime
TotalBytesSent
TCPOpenRequestTime
TCPOpenResponseTime
InternetGatewayDevice.UDPEchoConfig.
PacketsReceived
PacketsResponded
BytesReceived
BytesResponded
TimeFirstPacketReceived
TimeLastPacketReceived
InternetGatewayDevice.QueueManagement.QueueStats.{i}.
OutputPackets
OutputBytes
DroppedPackets
DroppedBytes
QueueOccupancyPackets
QueueOccupancyPercentage
InternetGatewayDevice.TraceRouteDiagnostics.
DiagnosticsState
ResponseTime
RouteHopsNumberOfEntries
InternetGatewayDevice.TraceRouteDiagnostics.RouteHops.{i}.
HopHost
HopHostAddress
HopErrorCode
HopRTTimes
InternetGatewayDevice.LANDevice.{i}.WLANConfiguration.{i}.Stats.
ErrorsSent
ErrorsReceived
UnicastPacketsSent
UnicastPacketsReceived
DiscardPacketsSent
DiscardPacketsReceived
MulticastPacketsSent
MulticastPacketsReceived
BroadcastPacketsSent
BroadcastPacketsReceived
UnknownProtoPacketsReceived
InternetGatewayDevice.WANDevice.{i}.WANDSLInterfaceConfig.TestParams.
HLOGGds
HLOGGus
HLOGpsds
HLOGpsus
HLOGMTds
HLOGMTus
QLNGds
QLNGus
QLNpsds
QLNpsus
QLNMTds
QLNMTus
SNRGds
SNRGus
SNRpsds
SNRpsus
SNRMTds
SNRMTus
LATNds
LATNus
SATNds
SATNus
InternetGatewayDevice.WANDevice.{i}.WANConnectionDevice.{i}.WANPTMLinkConfig.Stats.
BytesSent
BytesReceived
FramesSent
FramesReceived
ErrorsSent
ErrorsReceived
UnicastPacketsSent
UnicastPacketsReceived
DiscardPacketsSent
DiscardPacketsReceived
MulticastPacketsSent
MulticastPacketsReceived
BroadcastPacketsSent
BroadcastPacketsReceived
UnknownProtoPacketsReceived
InternetGatewayDevice.DeviceInfo.MemoryStatus.
Free
InternetGatewayDe