Broadband Forum

    DATA MODEL DEFINITION


TR-069 Device:1.0 Root Object definition
tr-106-1-0-0.xml

License

Copyright (c) 2008-2017, Broadband Forum

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3. Neither the name of the copyright holder nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The above license is used as a license under copyright only. Please reference the Forum IPR Policy for patent licensing terms <https://www.broadband-forum.org/ipr-policy>.

Any moral rights which are necessary to exercise under the above license grant are also deemed granted under this license.

Table of Contents

Data Types

The Parameters defined in this specification make use of a limited subset of the default SOAP data types [SOAP1.1]. These data types and the named data types used by this specification are described below.

Note: A Parameter that is defined to be one of the named data types is reported as such at the beginning of the Parameter's description via a reference back to the associated data type definition (e.g. [MacAddress]). However, such parameters still indicate their SOAP data type.

Data Type Base Type Description
Alias string(64)

A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference.

If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069a4] and described in [Appendix II/TR-069a4], the following mandatory constraints MUST be enforced:

  • Its value MUST NOT be empty.
  • Its value MUST start with a letter.
  • If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix.
  • The CPE MUST NOT change the parameter value.
Dbm1000 int The value is measured in dBm/1000, i.e. the value divided by 1000 is dB relative to 1 mW. For example, -12345 means -12.345 dBm, 0 means 0 dBm (1 mW) and 12345 means 12.345 dBm.
IEEE_EUI64 string(23)

The IEEE EUI 64-bit identifier as defined in [EUI64]. The IEEE defined 64-bit extended unique identifier (EUI-64) is a concatenation of:

  • The 24-bit (OUI-24) or 36-bit (OUI-36) company_id value assigned by the IEEE Registration Authority (IEEE-RA), and
  • The extension identifier (40 bits for OUI-24 or 28 bits for OUI-36) assigned by the organization with that company_id assignment.

Possible patterns:

  • <Empty> (an empty string)
  • ([0-9A-Fa-f][0-9A-Fa-f]:){7}([0-9A-Fa-f][0-9A-Fa-f])
IPAddress string(45)

IP address, i.e. IPv4 address (or IPv4 subnet mask) or IPv6 address.

All IPv4 addresses and subnet masks MUST be represented as strings in IPv4 dotted-decimal notation. Here are some examples of valid IPv4 address textual representations:

  • 216.52.29.100
  • 192.168.1.254

All IPv6 addresses MUST be represented using any of the 3 standard textual representations defined in [RFC4291] Sections 2.2.1, 2.2.2 and 2.2.3. Both lower-case and upper-case letters can be used, but use of lower-case letters is RECOMMENDED. Here are some examples of valid IPv6 address textual representations:

  • 1080:0:0:800:ba98:3210:11aa:12dd
  • 1080::800:ba98:3210:11aa:12dd
  • 0:0:0:0:0:0:13.1.68.3

IPv6 addresses MUST NOT include zone identifiers. Zone identifiers are discussed in [Section 6/RFC4007].

Unspecified or inapplicable addresses (or IPv4 subnet masks) MUST be represented as empty strings unless otherwise specified by the parameter definition.

IPPrefix string(49)

IPv4 or IPv6 routing prefix in Classless Inter-Domain Routing (CIDR) notation [RFC4632]. This is specified as an IP address followed by an appended "/n" suffix, where n (the prefix size) is an integer in the range 0-32 (for IPv4) or 0-128 (for IPv6) that indicates the number of (leftmost) '1' bits of the routing prefix.

  • IPv4 example: 192.168.1.0/24
  • IPv6 example: 2001:edff:fe6a:f76::/64

If the IP address part is unspecified or inapplicable, it MUST be an empty string unless otherwise specified by the parameter definition. In this case the IP prefix will be of the form "/n".

If the entire IP prefix is unspecified or inapplicable, it MUST be an empty string unless otherwise specified by the parameter definition.

IPv4Address IPAddress(15)

IPv4 address (or subnet mask).

Can be any IPv4 address that is permitted by the IPAddress data type.

IPv4Prefix IPPrefix(18)

IPv4 address prefix.

Can be any IPv4 prefix that is permitted by the IPPrefix data type.

IPv6Address IPAddress(45)

IPv6 address.

Can be any IPv6 address that is permitted by the IPAddress data type.

IPv6Prefix IPPrefix(49)

IPv6 address prefix.

Can be any IPv6 prefix that is permitted by the IPPrefix data type.

MACAddress string(17)

All MAC addresses are represented as strings of 12 hexadecimal digits (digits 0-9, letters A-F or a-f) displayed as six pairs of digits separated by colons. Unspecified or inapplicable MAC addresses MUST be represented as empty strings unless otherwise specified by the parameter definition. Possible patterns:

  • <Empty> (an empty string)
  • ([0-9A-Fa-f][0-9A-Fa-f]:){5}([0-9A-Fa-f][0-9A-Fa-f])
StatsCounter32 unsignedInt

A 32-bit statistics parameter, e.g. a byte counter.

This data type SHOULD NOT be used for statistics parameters whose values might become greater than the maximum value that can be represented as an unsignedInt (i.e. 0xffffffff, referred to below as maxval). StatsCounter64 SHOULD be used for such parameters.

The value maxval indicates that no data is available for this parameter. In the unlikely event that the actual value of the statistic is maxval, the CPE SHOULD return maxval - 1.

The actual value of the statistic might be greater than maxval. Such values SHOULD wrap around through zero.

The term packet is to be interpreted as the transmission unit appropriate to the protocol layer in question, e.g. an IP packet or an Ethernet frame.

StatsCounter64 unsignedLong

A 64-bit statistics parameter, e.g. a byte counter.

This data type SHOULD be used for all statistics parameters whose values might become greater than the maximum value that can be represented as an unsignedInt.

The maximum value that can be represented as an unsignedLong (i.e. 0xffffffffffffffff) indicates that no data is available for this parameter.

The term packet is to be interpreted as the transmission unit appropriate to the protocol layer in question, e.g. an IP packet or an Ethernet frame.

UUID string(36:36)

Universally Unique Identifier. See [RFC4122]. Possible patterns:

  • [A-Fa-f0-9]{8}-[A-Fa-f0-9]{4}-[A-Fa-f0-9]{4}-[A-Fa-f0-9]{4}-[A-Fa-f0-9]{12}
ZigBeeNetworkAddress string(4)

The ZigBee 16-bit network address (NWK) as defined in [ZigBee2007]. The address is assigned to a device by the network layer and used by the network layer for routing messages between devices. Possible patterns:

  • <Empty> (an empty string)
  • ([0-9A-Fa-f]){4}
base64 -

Base64 encoded binary (no line-length limitation).

A minimum and maximum allowed length can be indicated using the form base64(Min:Max), where Min and Max are the minimum and maximum length in characters before Base64 encoding. If either Min or Max are missing, this indicates no limit, and if Min is missing the colon can also be omitted, as in base64(Max). Multiple comma-separated ranges can be specified, in which case the length MUST be in one of the ranges.

boolean - Boolean, where the allowed values are 0 or 1 (or equivalently, true or false).
dateTime - The subset of the ISO 8601 date-time format defined by the SOAP dateTime type.
hexBinary -

Hex encoded binary.

A minimum and maximum allowed length can be indicated using the form hexBinary(Min:Max), where Min and Max are the minimum and maximum length in characters before Hex Binary encoding. If either Min or Max are missing, this indicates no limit, and if Min is missing the colon can also be omitted, as in hexBinary(Max). Multiple comma-separated ranges can be specified, in which case the length MUST be in one of the ranges.

int -

Integer in the range -2147483648 to +2147483647, inclusive.

For some int types, a value range is given using the form int[Min:Max] or int[Min:Max step Step] where the Min and Max values are inclusive. If either Min or Max are missing, this indicates no limit. If Step is missing, this indicates a step of 1. Multiple comma-separated ranges can be specified, in which case the value will be in one of the ranges.

long -

Long integer in the range -9223372036854775808 to 9223372036854775807, inclusive.

For some long types, a value range is given using the form long[Min:Max] or long[Min:Max step Step], where the Min and Max values are inclusive. If either Min or Max are missing, this indicates no limit. If Step is missing, this indicates a step of 1. Multiple comma-separated ranges can be specified, in which case the value will be in one of the ranges.

object - A container for parameters and/or other objects. The full Path Name of a parameter is given by the parameter name appended to the full Path Name of the object it is contained within.
string - For strings, a minimum and maximum allowed length can be indicated using the form string(Min:Max), where Min and Max are the minimum and maximum string length in characters. If either Min or Max are missing, this indicates no limit, and if Min is missing the colon can also be omitted, as in string(Max). Multiple comma-separated ranges can be specified, in which case the string length will be in one of the ranges.
unsignedInt -

Unsigned integer in the range 0 to 4294967295, inclusive.

For some unsignedInt types, a value range is given using the form unsignedInt[Min:Max] or unsigned[Min:Max step Step], where the Min and Max values are inclusive. If either Min or Max are missing, this indicates no limit. If Step is missing, this indicates a step of 1. Multiple comma-separated ranges can be specified, in which case the value will be in one of the ranges.

unsignedLong -

Unsigned long integer in the range 0 to 18446744073709551615, inclusive.

For some unsignedLong types, a value range is given using the form unsignedLong[Min:Max] or unsignedLong[Min:Max step Step], where the Min and Max values are inclusive. If either Min or Max are missing, this indicates no limit. If Step is missing, this indicates a step of 1. Multiple comma-separated ranges can be specified, in which case the value will be in one of the ranges.

References

[OUI] Organizationally Unique Identifiers (OUIs).
[RFC3066] RFC 3066, Tags for the Identification of Languages, IETF.
[RFC4122] RFC 4122, A Universally Unique IDentifier (UUID) URN Namespace, IETF, 2005.
[RFC4291] RFC 4291, IP Version 6 Addressing Architecture, IETF, 2006.
[RFC4632] RFC 4632, Classless Inter-domain Routing (CIDR): The Internet Address Assignment and Aggregation Plan, IETF, 2006.
[SOAP1.1] Simple Object Access Protocol (SOAP) 1.1, W3C.
[TR-069] TR-069, CPE WAN Management Protocol, Broadband Forum, 2004.
[TR-069a4] TR-069 Amendment 4, CPE WAN Management Protocol, Broadband Forum, 2011.
[TR-106] TR-106, Data Model Template for TR-069-Enabled Devices, Broadband Forum, 2005.
[ZigBee2007] ZigBee 2007 Specification, ZigBee 2007 Specification, ZigBee Alliance, October 2007.

Device:1.0 Data Model

Name Type Write Description Object Default Version
Device. object - The top-level object for a Device. - 1.0
DeviceSummary string­(1024) - See [Section 3.7/TR-106]. - 1.0
Device.Services. object - This object contains general services information. - 1.0
Device.DeviceInfo. object - This object contains general device information. - 1.0
Manufacturer string­(64) - The manufacturer of the CPE (human readable string). - 1.0
ManufacturerOUI string­(6) - Organizationally unique identifier of the device manufacturer. Represented as a six hexadecimal-digit value using all upper-case letters and including any leading zeros. The value MUST be a valid OUI as defined in [OUI]. - 1.0
ModelName string­(64) - Model name of the CPE (human readable string). - 1.0
Description string­(256) - A full description of the CPE device (human readable string). - 1.0
ProductClass string­(64) - Identifier of the class of product for which the serial number applies. That is, for a given manufacturer, this parameter is used to identify the product or class of product over which the SerialNumber parameter is unique. - 1.0
SerialNumber string­(64) - Serial number of the CPE. - 1.0
HardwareVersion string­(64) - A string identifying the particular CPE model and version. - 1.0
SoftwareVersion string­(64) -

A string identifying the software version currently installed in the CPE.

To allow version comparisons, this element SHOULD be in the form of dot-delimited integers, where each successive integer represents a more minor category of variation. For example, 3.0.21 where the components mean: Major.Minor.Build.

- 1.0
EnabledOptions string­(1024) - Comma-separated list (maximum list length 1024) of strings. Comma-separated list of the OptionName of each Option that is currently enabled in the CPE. The OptionName of each is identical to the OptionName element of the OptionStruct described in [TR-069]. Only those options are listed whose State indicates the option is enabled. - 1.0
AdditionalHardwareVersion string­(64) - Comma-separated list (maximum list length 64) of strings. A comma separated list of any additional versions. Represents any additional hardware version information the vendor may wish to supply. - 1.0
AdditionalSoftwareVersion string­(64) - Comma-separated list (maximum list length 64) of strings. A comma separated list of any additional versions. Represents any additional software version information the vendor may wish to supply. - 1.0
ProvisioningCode string­(64) W Identifier of the primary service provider and other provisioning information, which MAY be used by the ACS to determine service provider-specific customization and provisioning parameters. - 1.0
DeviceStatus string -

Current operational status of the device. Enumeration of:

- 1.0
UpTime unsignedInt - Time in seconds since the CPE was last restarted. - 1.0
FirstUseDate dateTime - Date and time in UTC that the CPE first both successfully established an IP-layer network connection and acquired an absolute time reference using NTP or equivalent over that network connection. The CPE MAY reset this date after a factory reset. - 1.0
DeviceLog string­(32768) - Vendor-specific log(s). - 1.0
Device.ManagementServer. object - This object contains parameters relating to the CPE's association with an ACS. - 1.0
URL string­(256) W

URL for the CPE to connect to the ACS using the CPE WAN Management Protocol.

This parameter MUST be in the form of a valid HTTP or HTTPS URL.

The host portion of this URL is used by the CPE for validating the ACS certificate when using SSL or TLS.

- 1.0
Username string­(256) W

Username used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol.

This username is used only for HTTP-based authentication of the CPE.

- 1.0
Password string­(256) W

Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol.

This password is used only for HTTP-based authentication of the CPE.

When read, this parameter returns an empty string, regardless of the actual value.

When read, this parameter returns an empty string, regardless of the actual value.

- 1.0
PeriodicInformEnable boolean W Whether or not the CPE must periodically send CPE information to the ACS using the Inform method call. - 1.0
PeriodicInformInterval unsignedInt­[1:] W The duration in seconds of the interval for which the CPE MUST attempt to connect with the ACS and call the Inform method if PeriodicInformEnable is true. - 1.0
PeriodicInformTime dateTime W

An absolute time reference in UTC to determine when the CPE should initiate the Inform method calls. Each Inform call must occur at this reference time plus or minus an integer multiple of the PeriodicInformInterval.

A zero dateTime value (0000-00-00T00:00:00) indicates that no particular time reference is specified. That is, the CPE may locally choose the time reference, required only to adhere to the specified PeriodicInformInterval.

- 1.0
ParameterKey string­(32) -

ParameterKey provides the ACS a reliable and extensible means to track changes made by the ACS. The value of ParameterKey MUST be equal to the value of the ParameterKey argument from the most recent successful SetParameterValues, AddObject, or DeleteObject method call from the ACS.

The CPE MUST set ParameterKey to the value specified in the corresponding method arguments if and only if the method completes successfully and no fault response is generated. If a method call does not complete successfully (implying that the changes requested in the method did not take effect), the value of ParameterKey MUST NOT be modified.

The CPE MUST only modify the value of ParameterKey as a result of SetParameterValues, AddObject, DeleteObject, or due to a factory reset. On factory reset, the value of ParameterKey MUST be set to an empty string.

- 1.0
ConnectionRequestURL string­(256) -

HTTP URL for an ACS to make a Connection Request notification to the CPE.

In the form:

http://host:port/path

The host portion of the URL MAY be the IP address for the management interface of the CPE in lieu of a host name.

- 1.0
ConnectionRequestUsername string­(256) W Username used to authenticate an ACS making a Connection Request to the CPE. - 1.0
ConnectionRequestPassword string­(256) W

Password used to authenticate an ACS making a Connection Request to the CPE.

When read, this parameter returns an empty string, regardless of the actual value.

When read, this parameter returns an empty string, regardless of the actual value.

- 1.0
UpgradesManaged boolean W Indicates whether or not the ACS will manage upgrades for the CPE. If true, the CPE SHOULD not use other means other than the ACS to seek out available upgrades. If false, the CPE MAY use other means for this purpose. - 1.0
KickURL string­(256) -

Present only for a CPE that supports the Kicked RPC method.

LAN-accessible URL from which the CPE can be kicked to initiate the Kicked RPC method call. MUST be an absolute URL including a host name or IP address as would be used on the LAN side of the CPE.

- 1.0
DownloadProgressURL string­(256) -

Present only for a CPE that provides a LAN-side web page to show progress during a file download.

LAN-accessible URL to which a web-server associated with the ACS may redirect a user's browser on initiation of a file download to observer the status of the download.

- 1.0
Device.GatewayInfo. object - This object contains information associated with a connected Internet Gateway Device. - 1.0
ManufacturerOUI string­(6) - Organizationally unique identifier of the associated Internet Gateway Device. An empty string indicates that there is no associated Internet Gateway Device that has been detected. - 1.0
ProductClass string­(64) - Identifier of the product class of the associated Internet Gateway Device. An empty string indicates either that there is no associated Internet Gateway Device that has been detected, or the Internet Gateway Device does not support the use of the product-class parameter. - 1.0
SerialNumber string­(64) - Serial number of the associated Internet Gateway Device. An empty string indicates that there is no associated Internet Gateway Device that has been detected. - 1.0
Device.Config. object - This object contains general configuration parameters. - 1.0
PersistentData string­(256) W Arbitrary user data that must persist across CPE reboots. - 1.0
ConfigFile string­(32768) W A dump of the currently running configuration on the CPE. This parameter enables the ability to backup and restore the last known good state of the CPE. It returns a vendor-specific document that defines the state of the CPE. The document must be capable of restoring the CPE's state when written back to the CPE using SetParameterValues. - 1.0
Device.Time. object - This object contains parameters relating an NTP or SNTP time client in the CPE. Support for this object is Optional. - 1.0
NTPServer1 string­(64) W First NTP timeserver. Either a host name or IP address. - 1.0
NTPServer2 string­(64) W Second NTP timeserver. Either a host name or IP address. - 1.0
NTPServer3 string­(64) W Third NTP timeserver. Either a host name or IP address. - 1.0
NTPServer4 string­(64) W Fourth NTP timeserver. Either a host name or IP address. - 1.0
NTPServer5 string­(64) W Fifth NTP timeserver. Either a host name or IP address. - 1.0
CurrentLocalTime dateTime - The current date and time in the CPE's local time zone. - 1.0
LocalTimeZone string­(256) W

The local time zone definition, encoded according to IEEE 1003.1 (POSIX). The following is an example value:

EST+5 EDT,M4.1.0/2,M10.5.0/2
- 1.0
Device.UserInterface. object - This object contains parameters relating to the user interface of the CPE. Support for this object is Optional. - 1.0
PasswordRequired boolean W

Present only if the CPE provides a password-protected LAN-side user interface.

Indicates whether or not the local user interface must require a password to be chosen by the user. If false, the choice of whether or not a password is used is left to the user.

- 1.0
PasswordUserSelectable boolean W

Present only if the CPE provides a password-protected LAN-side user interface and supports LAN-side Auto-Configuration.

Indicates whether or not a password to protect the local user interface of the CPE may be selected by the user directly, or must be equal to the password used by the LAN-side Auto-Configuration protocol.

- 1.0
UpgradeAvailable boolean W Indicates that a CPE upgrade is available, allowing the CPE to display this information to the user. - 1.0
WarrantyDate dateTime W Indicates the date and time in UTC that the warranty associated with the CPE is to expire. - 1.0
ISPName string­(64) W The name of the customer's ISP. - 1.0
ISPHelpDesk string­(32) W The help desk phone number of the ISP. - 1.0
ISPHomePage string­(256) W The URL of the ISP's home page. - 1.0
ISPHelpPage string­(256) W The URL of the ISP's on-line support page. - 1.0
ISPLogo base64­(4095) W Base64 encoded GIF or JPEG image. The binary image is constrained to 4095 bytes or less. - 1.0
ISPLogoSize unsignedInt­[0:4095] W

Un-encoded binary image size in bytes.

If ISPLogoSize input value is 0 then the ISPLogo is cleared.

ISPLogoSize can also be used as a check to verify correct transfer and conversion of Base64 string to image size.

- 1.0
ISPMailServer string­(256) W The URL of the ISP's mail server. - 1.0
ISPNewsServer string­(256) W The URL of the ISP's news server. - 1.0
TextColor string­(6) W The color of text on the GUI screens in RGB hexidecimal notation (e.g., FF0088). - 1.0
BackgroundColor string­(6) W The color of the GUI screen backgrounds in RGB hexidecimal notation (e.g., FF0088). - 1.0
ButtonColor string­(6) W The color of buttons on the GUI screens in RGB hexidecimal notation (e.g., FF0088). - 1.0
ButtonTextColor string­(6) W The color of text on buttons on the GUI screens in RGB hexidecimal notation (e.g., FF0088). - 1.0
AutoUpdateServer string­(256) W The server the CPE can check to see if an update is available for direct download to it. This MUST NOT be used by the CPE if the ManagementServer.UpgradesManaged? parameter is true. - 1.0
UserUpdateServer string­(256) W The server where a user can check via a web browser if an update is available for download to a PC. This MUST NOT be used by the CPE if the ManagementServer.UpgradesManaged? parameter is true. - 1.0
AvailableLanguages string­(256) - Comma-separated list (maximum list length 256) of strings. Comma-separated list of user-interface languages that are available, where each language is specified according to RFC 3066 [RFC3066]. - 1.0
CurrentLanguage string­(16) W Current user-interface language, specified according to RFC 3066 [RFC3066]. - 1.0
Device.LAN. object -

This object contains parameters relating to IP-based LAN connectivity of a device.

This object relates only to IP-layer LAN capabilities. Lower-layer aspects of LAN connectivity are not considered part of the common data model defined in this specification.

For a device that contains multiple IP interfaces, the scope of this object is limited to the default IP interface. Data that may be associated with other interfaces is not considered part of the common data model defined in this specification.

Support for this object is Optional.

- 1.0
AddressingType string W

The method used to assign an address to this interface. Enumeration of:

The ability to modify this parameter is optional.

- 1.0
IPAddress string­(45) W

[IPAddress] The current IP address assigned to this interface.

The ability to modify this parameter is optional, and this parameter cannot be modified if the AddressingType is DHCP.

- 1.0
SubnetMask string­(45) W

[IPAddress] The current subnet mask.

The ability to modify this parameter is optional, and this parameter cannot be modified if the AddressingType is DHCP.

- 1.0
DefaultGateway string W

The IP address of the current default gateway for this interface.

The ability to modify this parameter is optional, and this parameter cannot be modified if the AddressingType is DHCP.

- 1.0
DNSServers string­(256) W

Comma-separated list (maximum list length 256) of strings. Comma-separated list of IP address of the DNS servers for this interface.

The ability to modify this parameter is optional, and this parameter cannot be modified if the AddressingType is DHCP.

If this parameter is modifiable, the device MAY ignore any DNS servers beyond the first two in the list.

- 1.0
MACAddress string­(17) W [MACAddress] The physical address of this interface. Writable only if MACAddressOverride is present and equal to true. - 1.0
MACAddressOverride boolean W

Whether the value of MACAddress parameter can be overridden.

  • When true, MACAddress is writable.
  • When false, MACAddress is not writable, and the default MAC address assigned by the device SHOULD be restored.
- 1.0
DHCPOptionNumberOfEntries unsignedInt - Number of entries in the DHCP option table. - 1.0
Device.LAN.DHCPOption.{i}. object W This object is for configuration of DHCP options. Each instance of this object represents a DHCP option to be included by the DHCP client in client requests. The DHCP client MAY include any other options not specified in this table. - 1.0
Request boolean W

Whether this entry represents a request to the DHCP server, or a value to be sent by the DHCP client.

  • When true, this entry represents a request. In this case, the DHCP client MUST include the specified Tag in the Parameter Request List, as defined in RFC 2132. The Value parameter is ignored in this case.
  • When false, this entry represents a value to be sent by the DHCP client. In this case, the DHCP client MUST include a DHCP option formed from the Tag and Value parameters (with the Length derived from the length of the Value parameter).
- 1.0
Tag unsignedInt­[1:254] W Tag of the DHCP option as defined in RFC 2132. - 1.0
Value base64 W Base64 encoded octet string to be used as the Value of the DHCP option if Request is false. - 1.0
Device.LAN.Stats. object - This object contains statistics for the default IP interface. - 1.0
ConnectionUpTime unsignedInt -

The time in seconds that this IP interface has been connected.

  • If the IP interface is using DHCP, this is the time that the DHCP client has been only in the Bound or Renewing states and the lower-layer interface has continuously maintained a link.
  • If the IP interface is using static addressing, this is the time that the lower-layer interface has continuously maintained a link.
- 1.0
TotalBytesSent unsignedInt - Total number of IP payload bytes sent over this interface since the device was last restarted as specified in DeviceInfo.UpTime. - 1.0
TotalBytesReceived unsignedInt - Total number of IP payload bytes received over this interface since the device was last restarted as specified in DeviceInfo.UpTime. - 1.0
TotalPacketsSent unsignedInt - Total number of IP packets sent over this interface since the device was last restarted as specified in DeviceInfo.UpTime. - 1.0
TotalPacketsReceived unsignedInt - Total number of IP packets received over this interface since the device was last restarted as specified in DeviceInfo.UpTime. - 1.0
CurrentDayInterval unsignedInt -

Number of seconds since the beginning of the period used for collection of CurrentDay statistics.

The device MAY align the beginning of each CurrentDay interval with days in the UTC time zone, but is not required to do so.

- 1.0
CurrentDayBytesSent unsignedInt - Total number of IP payload bytes sent over this interface since the beginning of the current-day interval as specified by CurrentDayInterval. - 1.0
CurrentDayBytesReceived unsignedInt - Total number of IP payload bytes received over this interface since the beginning of the current-day interval as specified by CurrentDayInterval. - 1.0
CurrentDayPacketsSent unsignedInt - Total number of IP packets sent over this interface since the beginning of the current-day interval as specified by CurrentDayInterval. - 1.0
CurrentDayPacketsReceived unsignedInt - Total number of IP packets received over this interface since the beginning of the current-day interval as specified by CurrentDayInterval. - 1.0
QuarterHourInterval unsignedInt -

Number of seconds since the beginning of the period used for collection of QuarterHour statistics.

The device MAY align the beginning of each QuarterHour interval with real-time quarter-hour intervals, but is not required to do so.

- 1.0
QuarterHourBytesSent unsignedInt - Total number of IP payload bytes sent over this interface since the beginning of the quarter-hour interval as specified by QuarterHourInterval. - 1.0
QuarterHourBytesReceived unsignedInt - Total number of IP payload bytes received over this interface since the beginning of the quarter-hour interval as specified by QuarterHourInterval. - 1.0
QuarterHourPacketsSent unsignedInt - Total number of IP packets sent over this interface since the beginning of the quarter-hour interval as specified by QuarterHourInterval. - 1.0
QuarterHourPacketsReceived unsignedInt - Total number of IP packets received over this interface since the beginning of the quarter-hour interval as specified by QuarterHourInterval. - 1.0
Device.LAN.IPPingDiagnostics. object - This object is defines access to an IP-layer ping test for the default IP interface. - 1.0
DiagnosticsState string W

Indicates availability of diagnostic data. Enumeration of:

Value may be set to Requested to initiate the diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested.

When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic.

When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code 8 DIAGNOSTICS COMPLETE in the Inform message.

- 1.0
Host string­(256) W Host name or address of the host to ping. - 1.0
NumberOfRepetitions unsignedInt­[1:] W Number of repetitions of the ping test to perform before reporting the results. - 1.0
Timeout unsignedInt­[1:] W Timeout in milliseconds for the ping test. - 1.0
DataBlockSize unsignedInt­[1:65535] W Size of the data block in bytes to be sent for each ping. - 1.0
DSCP unsignedInt­[0:64] W DiffServ codepoint to be used for the test packets. By default the CPE should set this value to zero. - 1.0
SuccessCount unsignedInt - Result parameter indicating the number of successful pings (those in which a successful response was received prior to the timeout) in the most recent ping test. - 1.0
FailureCount unsignedInt - Result parameter indicating the number of failed pings in the most recent ping test. - 1.0
AverageResponseTime unsignedInt - Result parameter indicating the average response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero. - 1.0
MinimumResponseTime unsignedInt - Result parameter indicating the minimum response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero. - 1.0
MaximumResponseTime unsignedInt - Result parameter indicating the maximum response time in milliseconds over all repetitions with successful responses of the most recent ping test. If there were no successful responses, this value MUST be zero. - 1.0
Device.LAN.TraceRouteDiagnostics. object - This object is defines access to an IP-layer trace-route test for the default IP interface. - 1.0
DiagnosticsState string W

Indicates availability of diagnostic data. Enumeration of:

Value may be set to Requested to initiate the diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the DiagnosticsState to Requested.

When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the diagnostic.

When the diagnostic initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code 8 DIAGNOSTICS COMPLETE in the Inform message.

- 1.0
Host string­(256) W Host name or address of the host to find a route to. - 1.0
Timeout unsignedInt­[1:] W Timeout in milliseconds for the trace route test. - 1.0
DataBlockSize unsignedInt­[1:65535] W Size of the data block in bytes to be sent for each trace route. - 1.0
MaxHopCount unsignedInt­[1:64] W The maximum number of hop used in outgoing probe packets (max TTL). The default is 30 hops. - 1.0
DSCP unsignedInt­[0:64] W DiffServ codepoint to be used for the test packets. By default the CPE should set this value to zero. - 1.0
ResponseTime unsignedInt - Result parameter indicating the response time in milliseconds the most recent trace route test. If a route could not be determined, this value must be zero. - 1.0
NumberOfRouteHops unsignedInt - Result parameter indicating the number of hops within the discovered route. If a route could not be determined, this value must be zero. - 1.0
Device.LAN.TraceRouteDiagnostics.RouteHops.{i}. object - Result parameter indicating the components of the discovered route. If a route could not be determined, there will be no instances of this object. - 1.0
HopHost string­(256) - Result parameter indicating the Host Name or IP Address of a hop along the discovered route. - 1.0

Inform and Notification Requirements

Forced Inform Parameters

Parameter
Device.DeviceSummary
Device.DeviceInfo.HardwareVersion
Device.DeviceInfo.SoftwareVersion
Device.ManagementServer.ParameterKey
Device.ManagementServer.ConnectionRequestURL
Device.LAN.IPAddress

Forced Active Notification Parameters

Parameter

Default Active Notification Parameters

Parameter

Parameters for which Active Notification MAY be Denied

Parameter
Device.DeviceInfo.
ModelName
Description
UpTime
FirstUseDate
DeviceLog
Device.ManagementServer.
ParameterKey
Device.Time.
CurrentLocalTime
Device.LAN.Stats.
ConnectionUpTime
TotalBytesSent
TotalBytesReceived
TotalPacketsSent
TotalPacketsReceived
CurrentDayInterval
CurrentDayBytesSent
CurrentDayBytesReceived
CurrentDayPacketsSent
CurrentDayPacketsReceived
QuarterHourInterval
QuarterHourBytesSent
QuarterHourBytesReceived
QuarterHourPacketsSent
QuarterHourPacketsReceived
Device.LAN.IPPingDiagnostics.
DiagnosticsState
SuccessCount
FailureCount
AverageResponseTime
MinimumResponseTime
MaximumResponseTime
Device.LAN.TraceRouteDiagnostics.
DiagnosticsState
ResponseTime
NumberOfRouteHops
Device.LAN.TraceRouteDiagnostics.RouteHops.{i}.
HopHost

Profile Definitions

Notation

The following abbreviations are used to specify profile requirements:

Abbreviation Description
R Read support is REQUIRED.
W Both Read and Write support is REQUIRED. This MUST NOT be specified for a parameter that is defined as read-only.
P The object is REQUIRED to be present.
C Creation and deletion of instances of the object is REQUIRED.
A Creation of instances of the object is REQUIRED, but deletion is not REQUIRED.
D Deletion of instances of the object is REQUIRED, but creation is not REQUIRED.

Baseline:1 Profile

This table defines the Baseline:1 profile for the Device:1 data model. The minimum REQUIRED version for this profile is Device:1.0.

Name Requirement
Device. P
DeviceSummary R
Device.­DeviceInfo. P
Manufacturer R
ManufacturerOUI R
ModelName R
Description R
SerialNumber R
HardwareVersion R
SoftwareVersion R
DeviceStatus R
UpTime R
Device.­ManagementServer. P
URL W
Username W
Password W
PeriodicInformEnable W
PeriodicInformInterval W
PeriodicInformTime W
ParameterKey R
ConnectionRequestURL R
ConnectionRequestUsername W
ConnectionRequestPassword W
UpgradesManaged W

GatewayInfo:1 Profile

This table defines the GatewayInfo:1 profile for the Device:1 data model. The minimum REQUIRED version for this profile is Device:1.0.

Name Requirement
Device.­GatewayInfo. P
ManufacturerOUI R
ProductClass R
SerialNumber R

Time:1 Profile

This table defines the Time:1 profile for the Device:1 data model. The minimum REQUIRED version for this profile is Device:1.0.

Name Requirement
Device.­Time. P
NTPServer1 W
NTPServer2 W
CurrentLocalTime R
LocalTimeZone W

LAN:1 Profile

This table defines the LAN:1 profile for the Device:1 data model. The minimum REQUIRED version for this profile is Device:1.0.

Name Requirement
Device.­LAN. P
AddressingType R
IPAddress R
SubnetMask R
DefaultGateway R
DNSServers R
MACAddress R
Device.­LAN.­Stats. P
ConnectionUpTime R
TotalBytesSent R
TotalBytesReceived R
TotalPacketsSent R
TotalPacketsReceived R

IPPing:1 Profile

This table defines the IPPing:1 profile for the Device:1 data model. The minimum REQUIRED version for this profile is Device:1.0.

Name Requirement
Device.­LAN.­IPPingDiagnostics. P
DiagnosticsState W
Host W
NumberOfRepetitions W
Timeout W
DataBlockSize W
DSCP W
SuccessCount R
FailureCount R
AverageResponseTime R
MinimumResponseTime R
MaximumResponseTime R

TraceRoute:1 Profile

This table defines the TraceRoute:1 profile for the Device:1 data model. The minimum REQUIRED version for this profile is Device:1.0.

Name Requirement
Device.­LAN.­TraceRouteDiagnostics. P
DiagnosticsState W
Host W
Timeout W
DataBlockSize W
MaxHopCount W
DSCP W
ResponseTime R
NumberOfRouteHops R
Device.­LAN.­TraceRouteDiagnostics.­RouteHops.­{i}. P
HopHost R


Generated by Broadband Forum report.pl#422 (2018/03/28 version) on 2018/04/02 at 12:26:14.
report.pl --exitcode=fatals --cwmpindex=.. --nofontstyles --nowarnreport --quiet --report=html --outfile=tr-106-1-0-0.html tr-106-1-0-0.xml