VoiceServiceNumberOfEntries

unsignedInt

R

Number of entries in VoiceService table.

-

1.0

VoiceProfileNumberOfEntries

unsignedInt

R

Number of instances of VoiceProfile.

-

1.0

MaxProfileCount

unsignedInt

R

Maximum total number of distinct voice profiles supported.

Active Notification requests for this parameter MAY be denied.

-

1.0

MaxLineCount

unsignedInt

R

Maximum total number of lines supported across all profiles. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

MaxSessionsPerLine

unsignedInt

R

Maximum number of voice sessions supported for any given line across all profiles. A value greater than one indicates support for CPE provided conference calling. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

MaxSessionCount

unsignedInt

R

Maximum total number of voice sessions supported across all lines and profiles. (This might differ from MaxLineCount if each line can support more than one session for CPE provided conference calling. This value MAY be less than the product of MaxLineCount and MaxSessionsPerLine.)

Active Notification requests for this parameter MAY be denied.

-

1.0

SignalingProtocols

string[](:256)

R

Comma-separated list (maximum number of characters 256) of strings. Each item is a supported signaling protocol. Each list item matches one of:

• SIP
• MGCP
• MGCP-NCS
• H\.248
• H\.323
• SIP/\d+\.\d+
• MGCP/\d+\.\d+
• MGCP-NCS/\d+\.\d+
• H\.248/\d+\.\d+
• H\.323/\d+\.\d+
• X_.+ Each entry MAY be appended with a version indicator in the form "/X.Y". For example: "SIP/2.0" The list MAY include vendor-specific protocols, which MUST be in the format defined in [TR-106]. For example: "X_EXAMPLE-COM_MyProt"

Active Notification requests for this parameter MAY be denied.

-

1.0

Regions

string[](:256)

R

Comma-separated list (maximum number of characters 256) of strings. Each item is a geographic region supported by the CPE. Each item is the list MUST be an alpha-2 (two-character alphabetic) country code as specified by [ISO3166]. If an empty string indicates that the CPE does not support region-based customization via VoiceProfile.{i}..

Active Notification requests for this parameter MAY be denied.

-

1.0

RTCP

boolean

R

Support for RTCP. If true indicates support for VoiceProfile.{i}.RTP.RTCP.. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

SRTP

boolean

R

Support for SRTP. If true indicates support for VoiceProfile.{i}.RTP.SRTP.. If true also indicates that SRTPKeyingMethods and SRTPEncryptionKeySizes are present. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

SRTPKeyingMethods

string[](:256)

R

Comma-separated list (maximum number of characters 256) of strings. Each item is a keying protocol supported by this endpoint for SRTP. Each list item is an enumeration of:

• Null
• Static
• SDP
• IKE This list MAY include vendor-specific keying methods, which MUST use the format defined in [TR-106]. This parameter is applicable only if SRTP is true.

Active Notification requests for this parameter MAY be denied.

-

1.0

SRTPEncryptionKeySizes

unsignedInt[](:256)

R

Comma-separated list (maximum number of characters 256) of unsigned integers. Each item is a supported SRTP encryption key size. This parameter is applicable only if SRTP is true.

Active Notification requests for this parameter MAY be denied.

-

1.0

RTPRedundancy

boolean

R

Support for RTP payload redundancy as defined in [RFC2198]. If true indicates support for VoiceProfile.{i}.RTP.Redundancy.. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

DSCPCoupled

boolean

R

If true indicates that the CPE is constrained such that transmitted call control packets use the same DSCP marking as transmitted RTP packets. If true, the CPE MUST NOT support VoiceProfile.{i}.MGCP.DSCPMark, VoiceProfile.{i}.H323.DSCPMark, or VoiceProfile.{i}.SIP.DSCPMark for call control. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

EthernetTaggingCoupled

boolean

R

If true indicates that the CPE is constrained such that transmitted call control packets use the same Ethernet tagging (VLAN ID Ethernet Priority) as transmitted RTP packets. If true, the CPE MUST NOT support the VoiceProfile.{i}.MGCP.VLANIDMark, VoiceProfile.{i}.H323.VLANIDMark, VoiceProfile.{i}.SIP.VLANIDMark VoiceProfile.{i}.MGCP.EthernetPriorityMark, VoiceProfile.{i}.H323.EthernetPriorityMark, or VoiceProfile.{i}.SIP.EthernetPriorityMark for call control. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

PSTNSoftSwitchOver

boolean

R

If true indicates the CPE is capable of supporting the PSO_Activate Facility Action, which allows a call to be switched to a PSTN FXO (Foreign eXchange Office) line. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

FaxT38

boolean

R

Support for T.38 fax. If true indicates support for VoiceProfile.{i}.FaxT38.. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

FaxPassThrough

boolean

R

Support for fax pass-through. If true indicates support for VoiceProfile.{i}.FaxPassThrough. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

ModemPassThrough

boolean

R

Support for modem pass-through. If true indicates support for the VoiceProfile.{i}.ModemPassThrough. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

ToneGeneration

boolean

R

Support for tone generation. If true indicates support for VoiceProfile.{i}.Tone.. If true also indicates that ToneDescriptionsEditable, PatternBasedToneGeneration, and FileBasedToneGeneration are present. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

ToneDescriptionsEditable

boolean

R

If true indicates that VoiceProfile.{i}.Tone.Description. and VoiceProfile.{i}.Tone.Pattern. are editable (if entries can be added, removed, or modified). This parameter is applicable only if ToneGeneration is true.

Active Notification requests for this parameter MAY be denied.

-

1.0

PatternBasedToneGeneration

boolean

R

Support for tone generation by pattern specification. If true indicates support for VoiceProfile.{i}.Tone.. If ToneGeneration is true, at least one of PatternBasedToneGeneration and FileBasedToneGeneration MUST also be true. This parameter is applicable only if ToneGeneration is true.

Active Notification requests for this parameter MAY be denied.

-

1.0

FileBasedToneGeneration

boolean

R

Support for tone generation by file playback. If true indicates support for VoiceProfile.{i}.Tone.. If true also indicates that ToneFileFormats is present. If ToneGeneration is true, at least one of PatternBasedToneGeneration and FileBasedToneGeneration MUST also be true. This parameter is applicable only if ToneGeneration is true.

Active Notification requests for this parameter MAY be denied.

-

1.0

ToneFileFormats

string[](:256)

R

Comma-separated list (maximum number of characters 256) of strings. Each item is a supported tone file format. The specified file formats are raw codec data files, using one of the codecs listed below. Each list item is an enumeration of:

• G.711MuLaw
• G.711ALaw
• MP3
• WAV
• AMR The list MAY include vendor-specific -specific extensions, which MUST use the format defined in [TR-106]. Example: "G.711MuLaw, MP3, X_EXAMPLE-COM_MyFileFormat" If the CPE does not support tone files, this parameter MUST be an empty string. This parameter is applicable only if FileBasedToneGeneration is true.

Active Notification requests for this parameter MAY be denied.

-

1.0

RingGeneration

boolean

R

Support for ring generation. If true indicates support for control of ring generation via VoiceProfile.{i}.Line.{i}.Ringer.. If true also indicates that RingDescriptionsEditable, PatternBasedRingGeneration, and FileBasedRingGeneration are present. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

RingDescriptionsEditable

boolean

R

If true indicates that VoiceProfile.{i}.Line.{i}.Ringer.Description. and VoiceProfile.{i}.Line.{i}.Ringer.Pattern. are editable (if entries can be added, removed, or modified). This parameter is applicable only if RingGeneration is true.

Active Notification requests for this parameter MAY be denied.

-

1.0

PatternBasedRingGeneration

boolean

R

Support for ring generation by pattern specification. If true indicates support for VoiceProfile.{i}.Line.{i}.Ringer.Pattern.. If true also indicates that RingPatternEditable is present. This parameter is applicable only if RingGeneration is true.

Active Notification requests for this parameter MAY be denied.

-

1.0

RingPatternEditable

boolean

R

If true indicates that VoiceProfile.{i}.Line.{i}.Ringer.Pattern. is editable (if entries can be added, removed, or modified). This parameter is applicable only if PatternBasedRingGeneration is true.

Active Notification requests for this parameter MAY be denied.

-

1.0

FileBasedRingGeneration

boolean

R

Support for ring generation by file playback. If true indicates support for specification of ringer files in VoiceProfile.{i}.Line.{i}.Ringer.Description.. If true also indicates that RingFileFormats is present. This parameter is applicable only if RingGeneration is true.

Active Notification requests for this parameter MAY be denied.

-

1.0

RingFileFormats

string[](:256)

R

Comma-separated list (maximum number of characters 256) of strings. Each item is a supported ring file format. Each list item is an enumeration of:

• MIDI
• SMAF (MMF)
• RTTTL (RTTTL or RTX)
• MP3
• WAV
• AMR The list MAY include vendor-specific-specific extensions, which MUST use the format defined in [TR-106]. Example: "MIDI, AMR, X_EXAMPLE-COM_MyFileFormat" If the CPE does not support ring files, this parameter MUST be an empty string. This parameter is applicable only if FileBasedRingGeneration is true.

Active Notification requests for this parameter MAY be denied.

-

1.0

DigitMap

boolean

R

Support for a configurable digit map string. If true indicates full support for VoiceProfile.{i}.DigitMap.

Active Notification requests for this parameter MAY be denied.

-

1.0

NumberingPlan

boolean

R

Support for a configurable numbering plan. If true indicates support for a configurable numbering plan via VoiceProfile.{i}.NumberingPlan.. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

ButtonMap

boolean

R

Support for a configurable button map. If true indicates support for a configurable button map via VoiceProfile.{i}.ButtonMap. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

VoicePortTests

boolean

R

Support for remotely accessible voice-port tests. If true indicates support for PhyInterface.{i}.Tests.. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

Role

string

R

The role of this VoIP CPE. Enumeration of:

• UserAgent
• BackToBackUserAgents
• OutboundProxy A single VoiceService instance MUST have only one role. If a device includes the capabilities for more than one role, each role MUST be represented as separate VoiceService instances.

Active Notification requests for this parameter MAY be denied.

-

1.0

Extensions

string[](:256)

R

Comma-separated list (maximum number of characters 256) of strings. Each item is a supported SIP extension method. SIP extension methods MUST be in the form of the method name in upper case. The list MAY include vendor-specific extensions, which MUST use the format defined in [TR-106]. Examples:

"REFER"

"INFO"

"X_EXAMPLE-COM_MyExt"

Active Notification requests for this parameter MAY be denied.

-

1.0

Transports

string[](:256)

R

Comma-separated list (maximum number of characters 256) of strings. Each item is a supported SIP transport protocol. Each list item is an enumeration of:

• UDP
• TCP
• TLS
• SCTP The list MAY include vendor-specific transports, which MUST use the format defined in [TR-106].

Active Notification requests for this parameter MAY be denied.

-

1.0

URISchemes

string[](:256)

R

Comma-separated list (maximum number of characters 256) of strings. Each item is a supported URI scheme beyond the URI schemes required by the SIP specification. Each URI scheme is given by the URI prefix, without the colon separator. Example: "tel, fax"

Active Notification requests for this parameter MAY be denied.

-

1.0

EventSubscription

boolean

R

Support for SIP event subscription. If true value indicates support for VoiceProfile.{i}.SIP.EventSubscribe. and VoiceProfile.{i}.Line.{i}.SIP.EventSubscribe.{i}..

Active Notification requests for this parameter MAY be denied.

-

1.0

ResponseMap

boolean

R

Support for SIP response map. If true indicates support for VoiceProfile.{i}.SIP.ResponseMap.. This parameter is applicable only for a VoIP endpoint.

Active Notification requests for this parameter MAY be denied.

-

1.0

TLSAuthenticationProtocols

string[](:256)

R

Comma-separated list (maximum number of characters 256) of strings. Each item is a supported authentication protocol for TLS transport. Each list item is an enumeration of:

• Null
• MD5
• SHA-1 The list MAY include vendor-specific protocols, which MUST use the format defined in [TR-106]. Support for this parameter is applicable only if the value of Transports includes TLS.

Active Notification requests for this parameter MAY be denied.

-

1.0

TLSAuthenticationKeySizes

unsignedInt[](:256)

R

Comma-separated list (maximum number of characters 256) of unsigned integers. Each item represents a supported TLS authentication key size. Support for this parameter is applicable only if the value of Transports includes TLS and TLSAuthenticationProtocols is present and non-empty and includes at least one value other than Null.

Active Notification requests for this parameter MAY be denied.

-

1.0

TLSEncryptionProtocols

string[](:256)

R

Comma-separated list (maximum number of characters 256) of strings. Each item is a supported authentication protocol for TLS transport. Each list item is an enumeration of:

• Null
• RC4
• RC2
• DES
• 3DES The list MAY include vendor-specific protocols, which MUST use the format defined in [TR-106]. Support for this parameter is applicable only if the value of Transports includes "TLS.

Active Notification requests for this parameter MAY be denied.

-

1.0

TLSEncryptionKeySizes

unsignedInt[](:256)

R

Comma-separated list (maximum number of characters 256) of unsigned integers. Each item is a supported TLS encryption key size. Support for this parameter is applicable only if the value of Transports includes TLS and TLSEncryptionProtocols is present and non-empty and includes at least one value other than Null.

Active Notification requests for this parameter MAY be denied.

-

1.0

TLSKeyExchangeProtocols

string[](:256)

R

{{div: unexpected argument TLSEncryptionProtocols after: [classes()], [list(), ' Each item is a supported authentication protocol for TLS transport. ', enum(), nl(), 'The list MAY include vendor-specific protocols, which MUST use the format defined in ', bibref(TR-106), '.', nl(), 'Support for this parameter is applicable only if ', param(Transports), ' includes the value ', enum(TLS, Transports), ' and {param']}} is present and non-empty and includes at least one value other than Null.}}

Active Notification requests for this parameter MAY be denied.

-

1.0

Extensions

string[](:256)

R

Comma-separated list (maximum number of characters 256) of strings. Each item is a supported optional MGCP package. MGCP packages are listed using the uppercase package abbreviation. The list MAY include vendor-specific extensions, which MUST use the format defined in [TR-106]. Examples:

"BP"

"X_EXAMPLE-COM_MyExt"

Active Notification requests for this parameter MAY be denied.

-

1.0

FastStart

boolean

R

Support for H323 fast start. If true indicates support for fast start.

Active Notification requests for this parameter MAY be denied.

-

1.0

H235AuthenticationMethods

string[](:256)

R

Comma-separated list (maximum number of characters 256) of strings. Each item is a supported authentication method. Each list item is an enumeration of:

• dhExch (Diffie-Hellman)
• pwdSymEnc (password with symmetric encryption)
• pwdHash (password with hashing)
• certSign (certificate with signature)
• ipsec (IPSEC based connection)
• tls (TLS) The list MAY include vendor-specific protocols, which MUST use the format defined in [TR-106].

Active Notification requests for this parameter MAY be denied.

-

1.0

EntryID

unsignedInt(1:)

R

Unique identifier for each entry in this table.

Active Notification requests for this parameter MAY be denied.

-

1.0

Codec

string(:64)

R

Identifier of the type of codec. Enumeration of:

• G.711MuLaw
• G.711ALaw
• G.726
• G.729
• G.729a
• G.729e
• G.728
• G.723.1
• G.722
• G.722.1
• G.722.2
• GSM-FR
• GSM-HR
• GSM-EFR
• iLBC The parameter MAY instead be a vendor-specific codec, which MUST be in the format defined in [TR-106]. For example: "X_EXAMPLE-COM_MyCodec"

Active Notification requests for this parameter MAY be denied.

-

1.0

BitRate

unsignedInt

R

Bit rate, specified in bits per second. The value MUST be among the values appropriate for the specified codec.

Active Notification requests for this parameter MAY be denied.

-

1.0

PacketizationPeriod

string(:64)[]

R

Comma-separated list of strings (maximum number of characters per item 64). Each item is a supported packetization period, in milliseconds, or a continuous range of packetization periods. Ranges are indicated as a hyphen-separated pair of unsigned integers. Examples:

"20" indicates a single discrete value.

"10, 20, 30" indicates a set of discrete values.

"5-40" indicates a continuous inclusive range.

"5-10, 20, 30" indicates a continuous range in addition to a set of discrete values. A range MUST only be indicated if all values within the range are supported.

Active Notification requests for this parameter MAY be denied.

-

1.0

SilenceSuppression

boolean

R

If true indicates support for silence suppression for this codec.

Active Notification requests for this parameter MAY be denied.

-

1.0

Enable

string

W

Enables or disables all lines in this profile, or places them into a quiescent state. Enumeration of:

• Disabled
• Quiescent (OPTIONAL)
• Enabled If the value is Quiescent, in-progress sessions remain intact, but no new sessions are allowed. If the value is set to Quiescent in a CPE that does not support Quiescent, the CPE MUST treat it as if the value is Disabled.

Disabled

1.0

Reset

boolean

W

When written as true, forces the all lines in this profile to be reset, causing it to re-initialize and perform all start-up actions such as registration. Always false when read.

-

1.0

NumberOfLines

unsignedInt

R

Number of instances of VoiceProfile.{i}.Line.{i}. within this VoiceProfile. Applicable only for a VoIP endpoint.

0

1.0

Name

string(:64)

W

Human-readable string to identify the profile instance.

<Empty>

1.0

SignalingProtocol

string

W

The value MUST be a member of the list reported by the Capabilities.SignalingProtocols parameter. The protocol to be used for this profile.

<Empty>

1.0

MaxSessions

unsignedInt

W

Limit on the number of simultaneous voice sessions across all lines in this VoiceProfile. Must be less than or equal to Capabilities.MaxSessionCount. (This MAY be greater than NumberOfLines if each line can support more than one session, for example for CPE provided conference calling.)

0

1.0

DTMFMethod

string(:64)

W

Method by which DTMF digits MUST be passed. Enumeration of:

• InBand
• RFC2833
• SIPInfo (Applicable only if the value of SignalingProtocol is SIP) If DTMFMethodG711 is non-empty, then this parameter applies only when the current codec is not G.711. This parameter is applicable only for a VoIP endpoint.

InBand

1.0

DTMFMethodG711

string(:64)

W

Method by which DTMF digits MUST be passed if the the current codec is G.711. Enumeration of:

• InBand
• RFC2833
• SIPInfo (Applicable only if the value of SignalingProtocol is SIP)
• <Empty> (an empty string) If an empty string indicates that the value of DTMFMethod is to apply whether or not the the the current codec is G.711. This parameter is applicable only for a VoIP endpoint.

<Empty>

1.0

Region

string

W

The value MUST be a member of the list reported by the Capabilities.Regions parameter, or else be an empty string. The geographic region associated with this profile. This MAY be used by the CPE to customize localization settings. If an empty string indicates that the region is unspecified and the CPE SHOULD use default localization settings. This parameter is applicable only if Capabilities.Regions is non-empty.

-

1.0

DigitMap

string(:256)

W

Digit map controlling the transmission of dialed digit information. The string defines the criteria to be met as digits are collected before an outgoing request (e.g., a SIP INVITE) can be initiated. The syntax of this parameter is exactly the syntax used by MGCP as defined in [Section 2.1.5/RFC3435]. This parameter is applicable only if the device supports a dialing mechanism for which a dialing plan is needed (for example, a device with an explicit Dial button may not need to be aware of the dialing plan) and if the device does not already support a dialing plan mechanism for this profile (e.g., in-band via MGCP). This object is supported only if Capabilities.DigitMap is true. Applicable only for a VoIP endpoint.

<Empty>

1.0

DigitMapEnable

boolean

W

Enables use of DigitMap. When true, VoiceProfile.{i}.NumberingPlan., if present, MUST be ignored. This parameter is required if and only if both DigitMap and VoiceProfile.{i}.NumberingPlan are present. Applicable only for a VoIP endpoint.

true

1.0

STUNEnable

boolean

W

Enable or disable use of STUN to allow operation through NAT. Note: enabling STUN is to be interpreted as enabling the use of STUN for discovery, not use as a keep-alive mechanism.

false

1.0

STUNServer

string(:256)

W

Domain name or IP address of the STUN server.

<Empty>

1.0

NonVoiceBandwidthReservedUpstream

unsignedInt

W

For bandwidth-based admission control, indicates the amount of upstream bandwidth, in bits per second, that must be left available for non-voice traffic when determining whether a session can proceed. This parameter is appropriate only in implementations in which the actual bandwidth can be known, such as a VoIP device embedded in a DSL B-NT.

0

1.0

NonVoiceBandwidthReservedDownstream

unsignedInt

W

For bandwidth-based admission control, indicates the amount of downstream bandwidth, in bits per second, that must be left available for non-voice traffic when determining whether a session can proceed. This parameter is appropriate only in implementations in which the actual bandwidth can be known, such as a VoIP device embedded in a DSL B-NT.

0

1.0

PSTNFailOver

boolean

W

Specifies whether or not the CPE SHOULD fail over to PSTN service, if available, on loss of connectivity to the VoIP service. This parameter is appropriate only in implementations in which PSTN fail-over is possible.

false

1.0

FaxPassThrough

string

W

Specifies the behavior of the CPE for pass-through of fax data. Enumeration of:

• Disable (Prevents the CPE from switching to a fax pass-through mode)
• Auto (Allows the CPE to automatically detect fax data to determine whether or not to switch to a fax pass-through mode)
• Force (Forces the CPE to switch to a fax pass-through mode regardless of whether fax signaling is detected) If this parameter is supported, the value of Capabilities.FaxPassThrough MUST be true. This parameter is appropriate only for a VoIP endpoint.

Auto

1.0

ModemPassThrough

string

W

Specifies the behavior of the CPE for pass-through of modem data. Enumeration of:

• Disable (Prevents the CPE from switching to a modem pass-through mode)
• Auto (Allows the CPE to automatically detect modem data to determine whether or not to switch to a modem pass-through mode)
• Force (Forces the CPE to switch to a modem pass-through mode regardless of whether modem signaling is detected) If this parameter is supported, the value of Capabilities.ModemPassThrough MUST be true. This parameter is appropriate only for a VoIP endpoint.

Auto

1.0

Name

string(:256)

W

Human-readable string identifying the service provider.

<Empty>

1.0

URL

string(:256)

W

URL of the service provider for this profile instance.

<Empty>

1.0

ContactPhoneNumber

string(:32)

W

Phone number to contact the service provider for this profile instance.

<Empty>

1.0

EmailAddress

string(:256)

W

Email address to contact the service provider for this profile instance.

<Empty>

1.0

ProxyServer

string(:256)

W

Host name or IP address of the SIP proxy server. All SIP signaling traffic MUST be sent to the host indicated by this parameter and the port indicated by ProxyServerPort unless OutboundProxy is non-empty or a different route was discovered during normal operations SIP routing operation. Regardless of which host the traffic gets sent to (ProxyServer or OutboundProxy), the value of this parameter MUST be used to derive the URI placed into the SIP Route header field of all requests originated by this end-point unless a different proxy host was discovered dynamically during normal SIP routing operations.

<Empty>

1.0

ProxyServerPort

unsignedInt(0:65535)

W

Destination port to be used in connecting to the SIP server.

5060

1.0

ProxyServerTransport

string

W

The value MUST be a member of the list reported by the Capabilities.SIP.Transports parameter. Transport protocol to be used in connecting to the SIP server.

UDP

1.0

RegistrarServer

string(:256)

W

Host name or IP address of the SIP registrar server. If this parameter is an empty string, the CPE MUST obtain all of the registrar server configuration information, including host name or IP address, port, and transport protocol, from the values in ProxyServer, ProxyServerPort, and ProxyServerTransport and MUST ignore the values in RegistrarServer, RegistrarServerPort and RegistrarServerTransport.

<Empty>

1.0

RegistrarServerPort

unsignedInt(0:65535)

W

Destination port to be used in connecting to the SIP registrar server. If RegistrarServer is empty the CPE MUST obtain all of the registrar server configuration information, including host name or IP address, port, and transport protocol, from the values in ProxyServer, ProxyServerPort, and ProxyServerTransport and MUST ignore the values in RegistrarServer, RegistrarServerPort and RegistrarServerTransport.

5060

1.0

RegistrarServerTransport

string

W

The value MUST be a member of the list reported by the Capabilities.SIP.Transports parameter. Transport protocol to be used in connecting to the registrar server. Each list item is an enumeration of:

• UDP
• TCP
• TLS
• SCTP If RegistrarServer is empty the CPE MUST obtain all of the registrar server configuration information, including host name or IP address, port, and transport protocol, from the values in ProxyServer, ProxyServerPort, and ProxyServerTransport and MUST ignore the values in RegistrarServer, RegistrarServerPort and RegistrarServerTransport.

UDP

1.0

UserAgentDomain

string(:256)

W

CPE domain string. If an empty string, the CPE SHOULD use its IP address as the domain.

<Empty>

1.0

UserAgentPort

unsignedInt(0:65535)

W

Port used for incoming call control signaling.

0

1.0

UserAgentTransport

string

W

The value MUST be a member of the list reported by the Capabilities.SIP.Transports parameter. Transport protocol to be used for incoming call control signaling.

UDP

1.0

OutboundProxy

string(:256)

W

Host name or IP address of the outbound proxy. If the value is not an empty string, the SIP endpoint MUST send all SIP traffic (requests and responses) to the host indicated by this parameter and the port indicated by OutboundProxyPort. This MUST be done regardless of the routes discovered using normal SIP operations, including use of Route headers initialized from Service-Route and Record-Route headers previously received. The OutboundProxy value is NOT used to generate the URI placed into the Route header of any requests.

<Empty>

1.0

OutboundProxyPort

unsignedInt(0:65535)

W

Destination port to be used in connecting to the outbound proxy. This parameter MUST be ignored unless the value of OutboundProxy is non-empty.

5060

1.0

Organization

string(:256)

W

Text string to be used in the Organization header.

<Empty>

1.0

RegistrationPeriod

unsignedInt(1:)

W

Period over which the user agent must periodically register, in seconds.

-

1.0

TimerT1

unsignedInt(1:)

W

Value of SIP timer T1, in milliseconds, as defined in [RFC3261].

-

1.0

TimerT2

unsignedInt(1:)

W

Value of SIP timer T2, in milliseconds, as defined in [RFC3261].

-

1.0

TimerT4

unsignedInt(1:)

W

Value of SIP timer T4, in milliseconds, as defined in [RFC3261].

-

1.0

TimerA

unsignedInt(1:)

W

Value of SIP timer A, in milliseconds, as defined in [RFC3261].

-

1.0

TimerB

unsignedInt(1:)

W

Value of SIP timer B, in milliseconds, as defined in [RFC3261].

-

1.0

TimerC

unsignedInt(1:)

W

Value of SIP timer C, in milliseconds, as defined in [RFC3261].

-

1.0

TimerD

unsignedInt(1:)

W

Value of SIP timer D, in milliseconds, as defined in [RFC3261].

-

1.0

TimerE

unsignedInt(1:)

W

Value of SIP timer E, in milliseconds, as defined in [RFC3261].

-

1.0

TimerF

unsignedInt(1:)

W

Value of SIP timer F, in milliseconds, as defined in [RFC3261].

-

1.0

TimerG

unsignedInt(1:)

W

Value of SIP timer G, in milliseconds, as defined in [RFC3261].

-

1.0

TimerH

unsignedInt(1:)

W

Value of SIP timer H, in milliseconds, as defined in [RFC3261].

-

1.0

TimerI

unsignedInt(1:)

W

Value of SIP timer I, in milliseconds, as defined in [RFC3261].

-

1.0

TimerJ

unsignedInt(1:)

W

Value of SIP timer J, in milliseconds, as defined in [RFC3261].

-

1.0

TimerK

unsignedInt(1:)

W

Value of SIP timer K, in milliseconds, as defined in [RFC3261].

-

1.0

InviteExpires

unsignedInt(1:)

W

Invite request Expires header value, in seconds.

-

1.0

ReInviteExpires

unsignedInt(1:)

W

Re-invite request Expires header value, in seconds.

-

1.0

RegisterExpires

unsignedInt(1:)

W

Register request Expires header value, in seconds.

-

1.0

RegistersMinExpires

unsignedInt(1:)

W

Register request Min-Expires header value, in seconds.

-

1.0

RegisterRetryInterval

unsignedInt(1:)

W

Register retry interval, in seconds.

-

1.0

InboundAuth

string

W

Type of inbound authentication, if any, required.

Enumeration of:

• None
• Digest

None

1.0

InboundAuthUsername

string(:256)

W

If inbound authentication is required, the username credentials.

<Empty>

1.0

InboundAuthPassword

string(:256)

W

If inbound authentication is required, the password credentials.

When read, this parameter returns an empty string, regardless of the actual value.

<Empty>

1.0

UseCodecPriorityInSDPResponse

boolean

W

When true, in the SDP included in an OK response to an Invite, the first listed codec MUST be the highest priority codec among those offered in the Invite, based on the priorities specified in VoiceProfile.{i}.Line.{i}.Codec.List.{i}.. The list of codecs in the SDP MAY also include other lower priority codecs. When false, there is no specific requirement for choosing the codecs listed in the SDP included in an OK response.

false

1.0

DSCPMark

unsignedInt(0:63)

W

Diffserv code point to be used for outgoing SIP signaling packets.

0

1.0

VLANIDMark

int(-1:)

W

VLAN ID (as defined in [802.1Q-2005]) to be used for outgoing SIP signaling packets for this profile. A value of -1 indicates the default value is to be used. If either VLANIDMark or EthernetPriorityMark are greater than zero, then the outgoing frames MUST be tagged. Otherwise, the outgoing frames MAY be tagged or untagged.

-1

1.0

EthernetPriorityMark

int(-1:)

W

Ethernet priority code (as defined in [802.1Q-2005]) to be used for outgoing SIP signaling packets for this profile. A value of -1 indicates the default value is to be used. If either VLANIDMark or EthernetPriorityMark are greater than zero, then the outgoing frames MUST be tagged. Otherwise, the outgoing frames MAY be tagged or untagged.

-1

1.0

SIPEventSubscribeNumberOfElements

unsignedInt

R

Indicates the number of EventSubscribe objects.

0

1.0

SIPResponseMapNumberOfElements

unsignedInt(0:999)

R

Indicates the number of SIPResponseMap objects.

0

1.0

Event

string(:32)

W

SIP event name to appear in the EVENT header of the SIP SUBSCRIBE request.

<Empty>

1.0

Notifier

string(:256)

W

Host name or IP address of the event notify server.

<Empty>

1.0

NotifierPort

unsignedInt(0:65535)

W

Destination port to be used in connecting to the event notifier.

0

1.0

NotifierTransport

string

W

The value MUST be a member of the list reported by the Capabilities.SIP.Transports parameter. Transport protocol to be used in connecting to the event notifier.

UDP

1.0

ExpireTime

unsignedInt

W

Subscription refresh timer, in seconds.

-

1.0

SIPResponseNumber

unsignedInt(100:999)

W

The SIP Response code number.

100

1.0

TextMessage

string(:64)

W

The message to be provided on the screen or display of the VoIP device when the SIP response is received. If this parameter is not an empty string, display of this text preempts the value of VoiceProfile.{i}.Tone.Description.{i}.ToneText associated with Tone. If this parameter is an empty string, the value of VoiceProfile.{i}.Tone.Description.{i}.ToneText associated with Tone, if any, is displayed instead. This parameter is applicable only for VoIP devices capable of text display.

<Empty>

1.0

Tone

unsignedInt

W

The tone to be played to the user when the SIP response is received. The value corresponds to EntryID of an entry in VoiceProfile.{i}.Tone.Description.. A value of zero, or any value that is not valid, results in no tone played. If the value of Capabilities.ToneGeneration is false, no tone is played regardless of the value of this parameter.

0

1.0

CallAgent1

string(:256)

W

Host name or IP address of the main MGCP call agent.

<Empty>

1.0

CallAgentPort1

unsignedInt(0:65535)

W

Destination port to be used in connecting with the main MGCP call agent.

0

1.0

CallAgent2

string(:256)

W

Host name or IP address of the backup MGCP call agent.

<Empty>

1.0

CallAgentPort2

unsignedInt(0:65535)

W

Destination port to be used in connecting with the backup MGCP call agent.

0

1.0

RetranIntervalTimer

unsignedInt(0:65535)

W

Message retransfer interval, in seconds.

1

1.0

MaxRetranCount

unsignedInt(0:65535)

W

Max number of message retransfers.

10

1.0

RegisterMode

string

W

Register mode.

Enumeration of:

• Wildcard
• Individual

Wildcard

1.0

LocalPort

unsignedInt(0:65535)

W

Port listening for incoming call control signaling.

0

1.0

Domain

string(:256)

W

CPE domain string. If an empty string, the CPE SHOULD use its IP address.

<Empty>

1.0

User

string(:64)

W

User string used in accessing the call agent.

<Empty>

1.0

DSCPMark

unsignedInt(0:63)

W

Diffserv code point to be used for outgoing MGCP signaling packets.

-

1.0

VLANIDMark

int(-1:)

W

VLAN ID (as defined in [802.1Q-2005]) to be used for outgoing MGCP signaling packets for this profile. A value of -1 indicates the default value is to be used. If either VLANIDMark or EthernetPriorityMark are greater than zero, then the outgoing frames MUST be tagged. Otherwise, the outgoing frames MAY be tagged or untagged.

-1

1.0

EthernetPriorityMark

int(-1:)

W

Ethernet priority code (as defined in [802.1D-2004]) to be used for outgoing MGCP signaling packets for this profile. A value of -1 indicates the default value is to be used. If either VLANIDMark or EthernetPriorityMark are greater than zero, then the outgoing frames MUST be tagged. Otherwise, the outgoing frames MAY be tagged or untagged.

-1

1.0

AllowPiggybackEvents

boolean

W

Indicates whether or not piggyback events are allowed to the MGCP call agent.

-

1.0

SendRSIPImmediately

boolean

W

Indicates whether or not to send RSIP immediately on restart.

-

1.0

Gatekeeper

string

W

Host name or IP address of H.323 Gatekeeper.

<Empty>

1.0

GatekeeperPort

unsignedInt

W

Destination port to be used in connecting to the H.323 Gatekeeper.

1719

1.0

GatekeeperID

string

W

Gatekeeper ID.

<Empty>

1.0

TimeToLive

unsignedInt

W

Defines the TimeToLive specification in the registration with the Gatekeeper in seconds.

86400

1.0

H235Authentication

boolean

W

Enables or disables usage of H.235 security baseline security profile as defined in [ITU-H.235.1] baseline security profile.

false

1.0

AuthPassword

string

W

Password to be used when H.235 is enabled.

When read, this parameter returns an empty string, regardless of the actual value.

<Empty>

1.0

SendersID

string

W

In ITU-T based H.235 authentication, the sendersID is the ID of the gateway as received from the Gatekeeper. As long as the endpointID is not received from the Gatekeeper, the sendersID will be applied as configured here. The generalID is the GatekeeperID.

<Empty>

1.0

DSCPMark

unsignedInt(0:63)

W

Diffserv code point to be used for outgoing H.323 signaling packets.

0

1.0

VLANIDMark

int(-1:)

W

VLAN ID (as defined in [802.1Q-2005]) to be used for outgoing H.323 signaling packets for this profile. A value of -1 indicates the default value is to be used. If either VLANIDMark or EthernetPriorityMark is greater than zero, then the outgoing frames MUST be tagged. Otherwise, the outgoing frames MAY be tagged or untagged.

-1

1.0

EthernetPriorityMark

int(-1:)

W

Ethernet priority code (as defined in [802.1D-2004]) to be used for outgoing H.323 signaling packets for this profile. A value of -1 indicates the default value is to be used. If either VLANIDMark or EthernetPriorityMark is greater than zero, then the outgoing frames MUST be tagged. Otherwise, the outgoing frames MAY be tagged or untagged.

-1

1.0

LocalPortMin

unsignedInt(0:65535)

W

Base of port range to be used for incoming RTP streams for this profile.

0

1.0

LocalPortMax

unsignedInt(0:65535)

W

Top of port range to be used for incoming RTP streams for this profile.

0

1.0

DSCPMark

unsignedInt(0:63)

W

Diffserv code point to be used for outgoing RTP packets for this profile. It is RECOMMENDED that by default the DSCP for RTP traffic be set to the value to indicate EF traffic.

-

1.0

VLANIDMark

int(-1:)

W

VLAN ID (as defined in [802.1Q-2005]) to be used for outgoing RTP packets for this profile. A value of -1 indicates the default value is to be used. If either VLANIDMark or EthernetPriorityMark is greater than zero, then the outgoing frames MUST be tagged. Otherwise, the outgoing frames MAY be tagged or untagged.

-1

1.0

EthernetPriorityMark

int(-1:)

W

Ethernet priority code (as defined in [802.1D-2004]) to be used for outgoing RTP packets for this profile. A value of -1 indicates the default value is to be used. If either VLANIDMark or EthernetPriorityMark is greater than zero, then the outgoing frames MUST be tagged. Otherwise, the outgoing frames MAY be tagged or untagged.

-1

1.0

TelephoneEventPayloadType

unsignedInt(0:128)

W

Payload type to be used for RTP telephone events. This parameter indicates the payload type to be used for DTMF events if transmission of DTMF information is in use according to [RFC2833].

-

1.0

Enable

boolean

W

Enable or disable RTCP.

-

1.0

TxRepeatInterval

unsignedInt(1:)

W

Transmission repeat interval, in milliseconds.

-

1.0

LocalCName

string(:64)

W

Local Cname (canonical name).

-

1.0

Enable

boolean

W

Enable or disable the use of SRTP. If RTCP is enabled, a true value of this parameter also implies the use of SRTCP.

-

1.0

KeyingMethods

string[](:256)

W

Each list item MUST be a member of the list reported by the Capabilities.SRTPKeyingMethods parameter. Comma-separated list (maximum number of characters 256) of strings. Each item is a keying method that may be used. By default this parameter MUST have the value of Capabilities.SRTPKeyingMethods-

-

1.0

EncryptionKeySizes

string[](:256)

W

Each list item MUST be a member of the list reported by the Capabilities.SRTPEncryptionKeySizes parameter. Comma-separated list (maximum number of characters 256) of strings. Each item is an encryption key size that may be used. By default this parameter MUST have the value of Capabilities.SRTPEncryptionKeySizes.

-

1.0

Enable

boolean

W

Enable or disable the use of RTP payload redundancy as defined by [RFC2198].

false

1.0

PayloadType

unsignedInt(0:127)

W

The Payload Type of RTP packet as defined in [RFC2198]. Values SHOULD be within the range of dynamic Payload Types (96-127).

0

1.0

BlockPayloadType

unsignedInt(0:127)

R

Block Payload Type of redundancy packet.

0

1.0

FaxAndModemRedundancy

int(-1:5)

W

Specifies the redundancy number for fax and modem pass-through data transmissions. A non-negative value indicates that [RFC2198] is to be used for fax and modem pass-through data. The value indicates the number of redundant copies to be transmitted (the total number transmitted is one plus this value). A value of -1 indicates [RFC2198] is not to be used for fax and modem pass-through data. If ModemRedundancy is present, then FaxAndModemRedundancy applies only to fax transmissions, but not to modem transmissions.

-1

1.0

ModemRedundancy

int(-1:5)

W

Specifies the redundancy number for modem pass-through data transmissions. A non-negative value indicates that [RFC2198] is to be used for modem pass-through data. The value indicates the number of redundant copies to be transmitted (the total number transmitted is one plus this value). A value of -1 indicates [RFC2198] is not to be used for modem pass-through data.

-1

1.0

DTMFRedundancy

int(-1:5)

W

Specifies the redundancy number for DTMF transmissions. A non-negative value indicates that [RFC2198] is to be used for DTMF. The value indicates the number of redundant copies to be transmitted (the total number transmitted is one plus this value). A value of -1 indicates [RFC2198] is not to be used for DTMF.

-1

1.0

VoiceRedundancy

int(-1:5)

W

Specifies the redundancy number for general voice transmissions. A non-negative value indicates that [RFC2198] is to be used for voice. The value indicates the number of redundant copies to be transmitted (the total number transmitted is one plus this value). A value of -1 indicates [RFC2198] is not to be used for voice.

-1

1.0

MaxSessionsUsingRedundancy

unsignedInt

W

The maximum number of sessions using [RFC2198] payload redundancy simultaneously in this VoiceProfile. A value of zero indicates no explicit limit on the number of sessions using redundancy.

0

1.0

MinimumNumberOfDigits

unsignedInt(1:40)

W

This is the minimum number of digits that must be collected before an outgoing request (e.g., a SIP INVITE) can be initiated. If "End of Dialing" (refer to the definition of the InterDigitTimer) occurs before the minimum number of digits has been reached then the number will be considered incomplete and no request will be initiated. In practice, searching VoiceProfile.{i}.NumberingPlan.PrefixInfo.{i}. should only commence once the minimum number of digits (as specified by this parameter) has been received.

-

1.0

MaximumNumberOfDigits

unsignedInt(1:40)

W

This is the maximum number of digits that may be collected before an outgoing request (e.g., a SIP INVITE) must be initiated. Any additional dialed digits will be ignored. This parameter is only used in the case that no match in VoiceProfile.{i}.NumberingPlan.PrefixInfo.{i}. has been found.

-

1.0

InterDigitTimerStd

unsignedInt(1:50000)

W

This timer is the maximum allowable time (expressed in milliseconds) between the dialing of digits. This timer is restarted every time a digit is dialed. Expiration of this timer indicates "End of Dialing".

-

1.0

InterDigitTimerOpen

unsignedInt(1:50000)

W

This timer is the maximum allowable time (expressed in milliseconds) between the dialing of digits once the minimum number of digits defined on a prefix based has been reached. This timer is only applicable to "open numbering", where the exact number of digits for a prefix is not known.

-

1.0

InvalidNumberTone

unsignedInt

W

The tone that should be provided to the user when the number dialed is determined to be invalid. The value corresponds to an instance of an EntryID in VoiceProfile.{i}.Tone.Description.. A value of zero, or any value that does not match a valid EntryID, results in no tone played. If Capabilities.ToneGeneration is equal to false, no tone is played regardless of the value of this parameter.

-

1.0

PrefixInfoMaxEntries

unsignedInt

R

This is the maximum number of instances of VoiceProfile.{i}.NumberingPlan.PrefixInfo.{i}. that can be supported.

-

1.0

PrefixInfoNumberOfEntries

unsignedInt

R

Indicates the number of instances of VoiceProfile.{i}.NumberingPlan.PrefixInfo.{i}..

-

1.0

PrefixRange

string(:42)

W

This is a string representation of a range of prefixes. Each prefix consists of a "From" part consisting of 1 to n digits (string representation) followed by an optional "To" part consisting of exactly one digit prefixed by a "-" symbol. It should be noted that only the characters "0-9", "*": and "#" can be used to represent the "From" and "To" parts of the prefix range. A further constraint is that the "To" digit MUST always be numerically greater than the last digit of the "From" part. Examples:

02

031-5

032

0325

*#34

#22

<Empty>

1.0

PrefixMinNumberOfDigits

unsignedInt(1:40)

W

This is the minimum number of allowable digits for the prefix range. Once the minimum number of digits has been reached, VoiceProfile.{i}.NumberingPlan.InterDigitTimerOpen will be used instead of VoiceProfile.{i}.NumberingPlan.InterDigitTimerStd. If the minimum number of digits has been reached and the inter-digit timer expires, an outgoing request should be initiated.

1

1.0

PrefixMaxNumberOfDigits

unsignedInt(1:40)

W

This is the maximum number of allowable digits for the prefix range. Once the number of digits received reaches this value an outgoing request should be initiated.

1

1.0

NumberOfDigitsToRemove

unsignedInt(0:40)

W

If this parameter has a non-zero value, the specified number of digits will be removed from the internal digit buffer (which contains the dialed digits) from the position specified by PosOfDigitsToRemove. Subsequently a search of PrefixInfo for a matching prefix using the modified number should be performed. Note that this parameter does not have any impact on the number sent in the outgoing request - but is instead only used for searching within the Numbering Plan. This parameter has no effect if it is set to 0. This parameter is provided to handle Carrier override and other codes that may prefix standard numbers and to ensure that the correct "End of Dialing" can be specified without significant data duplication.

0

1.0

PosOfDigitsToRemove

unsignedInt(0:40)

W

This parameter is used in conjunction with NumberOfDigitsToRemove. It specifies the position within the internal digit buffer from which the digits are to be removed.

0

1.0

DialTone

unsignedInt

W

The tone to be played by the VoIP device when the user has dialed exactly the same digits as defined in the prefix. The VoIP device will cease playing the tone once an additional digit has been dialed. The value corresponds to an instance of and EntryID in VoiceProfile.{i}.Tone.Description.. A value of zero, or any value that does not match a valid EntryID, results in no tone played. If Capabilities.ToneGeneration is equal to false, no tone is played regardless of the value of this parameter.

0

1.0

FacilityAction

string(:64)

W

This is a string representing a Facility Action implemented by the VoIP device. [Appendix A/TR-104] lists a set of defined values for this string. The parameter MAY instead indicate a vendor-specific FacilityAction, which MUST use the format defined in [TR-106]. An empty or unrecognized string (i.e., a Facility Action not supported by the CPE) should be treated as a normal outgoing request.

<Empty>

1.0

FacilityActionArgument

string(:256)

W

Optional argument associated with FacilityAction. The interpretation of the argument is dependent on a specific value of FacilityAction. Where used, the value is specified in [Appendix A/TR-104] in the definition of the corresponding FacilityAction value.

<Empty>

1.0

EventNumberOfEntries

unsignedInt

R

Indicates the number of entries in VoiceProfile.{i}.Tone.Event.{i}..

-

1.0

DescriptionNumberOfEntries

unsignedInt

R

Indicates the number of entries in VoiceProfile.{i}.Tone.Description.{i}..

-

1.0

PatternNumberOfEntries

unsignedInt

R

Indicates the number of entries in VoiceProfile.{i}.Tone.Pattern.{i}..

-

1.0

Function

string(:64)

R

The event for which the tone is to apply. Enumeration of:

• Busy
• Confirmation
• Dial
• MessageWaiting
• OffHookWarning
• RingBack
• ReOrder
• Stutterdial
• CallWaiting1
• CallWaiting2
• CallWaiting3
• CallWaiting4
• AlertingSignal
• SpecialDial
• SpecialInfo
• Release
• Congestion
• UserDefined1
• UserDefined2
• UserDefined3
• UserDefined4 The parameter MAY instead indicate a vendor-specific event name, which MUST use the format defined in [TR-106].

-

1.0

ToneID

unsignedInt

W

The EntryID of the entry in VoiceProfile.{i}.Tone.Description.{i}. for the tone to be associated with the given event. A value of zero indicates no tone is to be played for this event.

-

1.0

EntryID

unsignedInt(1:)

R

Unique identifier of this tone. Assigned by the CPE upon creation of the entry.

-

1.0

ToneEnable

boolean

W

Enables or disables the tone entry. If a disabled tone entry is referenced, the result is that no tone is played.

false

1.0

ToneName

string(:64)

W

Name of the tone. This parameter is required to be editable only Capabilities.ToneDescriptionsEditable is equal to true.

<Empty>

1.0

TonePattern

unsignedInt

W

EntryID of the entry in VoiceProfile.{i}.Tone.Pattern. that begins the tone pattern for this tone. If the tone is specified by a tone file instead of a tone pattern, this parameter MUST be set to zero. This parameter is applicable only if Capabilities.PatternBasedToneGeneration is equal to true. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

ToneFile

string(:256)

W

This is the file name of a tone file that has been downloaded to the CPE. The download may have occurred via the TR-069 Download mechanism or by some other means. If the tone is specified by a tone pattern instead of a tone file, this parameter MUST be an empty string. This parameter is applicable only if Capabilities.FileBasedToneGeneration is equal to true. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true.

<Empty>

1.0

ToneRepetitions

unsignedInt(0:255)

W

The default number of times the data in ToneFile should be repeated. If the value 0 (zero) is specified then ToneFile should be played indefinitely. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

ToneText

string(:64)

W

The text to be displayed by on the screen of the VoIP device when the tone is played and no specific error message has been provided. This parameter is applicable only for VoIP devices capable text display.

<Empty>

1.0

EntryID

unsignedInt(1:)

W

Identifier of a tone-pattern entry. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true. Note: when Capabilities.ToneDescriptionsEditable is true, this parameter is editable so that the NextEntryID values for each table entry can be pre-assigned for a series of associated table entries rather than requiring the ACS to set the value according to an ID assigned dynamically upon creation of each entry.

The Agent MUST choose an initial value that doesn't conflict with any existing entries.

-

1.0

ToneOn

boolean

W

Whether or not a tone is on during this phase of the pattern. If the value is false, the frequency and power parameters in this entry MUST be ignored. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true.

false

1.0

Frequency1

unsignedInt(0:4095)

W

First tone frequency in hertz. A value of zero indicates this tone component is not used. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

Power1

int

W

First tone power level in units of 0.1 dBm0. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

Frequency2

unsignedInt(0:4095)

W

Second tone frequency in hertz. A value of zero indicates this tone component is not used. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

Power2

int

W

Second tone power level in units of 0.1 dBm0. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

Frequency3

unsignedInt(0:4095)

W

Third tone frequency in hertz. A value of zero indicates this tone component is not used. This parameter is required to be editable only if the parameter is supported for reading and Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

Power3

int

W

Third tone power level in units of 0.1 dBm0. This parameter is required to be editable only if the parameter is supported for reading and Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

Frequency4

unsignedInt(0:4095)

W

Fourth tone frequency in herts. A value of zero indicates this tone component is not used. This parameter is required to be editable only if the parameter is supported for reading and Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

Power4

int

W

Fourth tone power level in units of 0.1 dBm0. This parameter is required to be editable only if the parameter is supported for reading and Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

ModulationFrequency

unsignedInt(0:4095)

W

Modulation frequency in hertz. A value of zero indicates this tone component is not used. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

ModulationPower

int

W

Modulation power level in units of 0.1 dBm0. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

Duration

unsignedInt

W

The duration of this phase of the tone pattern, in milliseconds. A value of zero indicates an unlimited duration. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

NextEntryID

unsignedInt

W

The EntryID for the next phase of the tone pattern, after the specified Duration of this phase has completed. A value of zero indicates that the tone pattern is to terminate after the current phase is completed. This parameter is required to be editable only if Capabilities.ToneDescriptionsEditable is equal to true.

0

1.0

NumberOfButtons

unsignedInt

R

Indicates the number of Button objects.

-

1.0

ButtonName

string(:16)

R

Name of the Button.

-

1.0

FacilityAction

string(:64)

W

This is an optional parameter that should only be specified for buttons related to a particular Facility Action (e.g., invocation of "Call Return") implemented by the VoIP device. [Appendix A/TR-104] lists a set of defined values for this string. The parameter MAY instead indicate a vendor-specific FacilityAction, which MUST use the format defined in [TR-106]. An empty or unrecognized string (i.e. a Facility Action not supported by the CPE) should be treated as no Facility Action to be taken. Note that If this parameter is specified (non-empty) then QuickDialNumber SHOULD be an empty string.

-

1.0

FacilityActionArgument

string(:256)

W

Optional argument associated with the specified FacilityAction. The interpretation of the argument is dependent on the specific FacilityAction. Where used, the value is specified in [Appendix A/TR-104] in the definition of the corresponding FacilityAction value.

<Empty>

1.0

QuickDialNumber

string(:40)

W

This is a string representing a quick dial destination number. Only the characters '0-9', '*' and '#' can be used. Note that If this parameter is specified (non-empty) then FacilityAction should be an empty string.

-

1.0

ButtonMessage

string(:64)

W

This string represents the message to be displayed on the screen when the button or function key is pressed.

-

1.0

UserAccess

boolean

W

This parameter indicates whether the user has permission to program the button or function key. If this parameter is set to true then FacilityAction, QuickDialNumber and ButtonMessage MUST all be an empty string.

-

1.0

Enable

boolean

W

Enable or disable the use of T.38.

-

1.0

BitRate

unsignedInt(2400,4800,7200,9600,12000,14400,33600)

W

Maximum data rate for fax.

-

1.0

HighSpeedPacketRate

unsignedInt(10,20,30,40)

W

The rate at which high speed data will be sent across the network, in milliseconds.

-

1.0

HighSpeedRedundancy

unsignedInt(0:3)

W

Specifies the packet-level redundancy for high-speed data transmissions (i.e., T.4 image data).

-

1.0

LowSpeedRedundancy

unsignedInt(0:5)

W

Specifies the packet-level redundancy for low-speed data transmissions (i.e., T.30 handshaking information).

-

1.0

TCFMethod

string

W

The method with which data is handled over the network.

Enumeration of:

• Local
• Network

-

1.0

Enable

string

W

Enables or disables this line, or places it into a quiescent state. Enumeration of:

• Disabled
• Quiescent (OPTIONAL)
• Enabled In the Quiescent state, in-progress sessions remain intact, but no new sessions are allowed. If this parameter is set to Quiescent in a CPE that does not support the Quiescent state, it MUST treat it the same as the Disabled state (and indicate Disabled in Status).

Disabled

1.0

DirectoryNumber

string(:32)

W

Directory number associated with this line. May be used to identify the line to the user. In case of H.323 signaling, this MUST be an E.164 number.

<Empty>

1.0

Status

string

R

Indicates the status of this line.

Enumeration of:

• Up
• Initializing
• Registering
• Unregistering
• Error
• Testing
• Quiescent
• Disabled

Disabled

1.0

CallState

string

R

Indicates the call state for this line.

Enumeration of:

• Idle
• Calling
• Ringing
• Connecting
• InCall
• Hold
• Disconnecting

Active Notification requests for this parameter MAY be denied.

Idle

1.0

PhyReferenceList

string[](:32)

W

Comma-separated list (maximum number of characters 32) of strings. Each item corresponds to the value of a particular instance of PhyInterface.{i}.InterfaceID.

-

1.0

RingMuteStatus

boolean

R

Whether or not ringing has been locally muted. Applicable only if the line is associated with a single telephony device for which ringing can be muted.

-

1.0

RingVolumeStatus

unsignedInt(0:100)

R

Percent value of current ringer volume level. Applicable only if the line is associated with a single telephony device for which the ringer volume can be controlled.

-

1.0

AuthUserName

string(:128)

W

Username used to authenticate the connection to the server.

<Empty>

1.0

AuthPassword

string(:128)

W

Password used to authenticate the connection to the server.

When read, this parameter returns an empty string, regardless of the actual value.

<Empty>

1.0

URI

string(:389)

W

URI by which the user agent will identify itself for this line. If empty, the actual URI used in the SIP signaling SHOULD be automatically formed by the CPE as: "sip:UserName@Domain" Where UserName is username given for this line in AuthUserName, and Domain is the domain given for this profile in VoiceProfile.{i}.SIP.UserAgentDomain. If VoiceProfile.{i}.SIP.UserAgentDomain is an empty string, then the IP address of the CPE SHOULD be used for the domain. If URI is non-empty, but is a SIP or SIPS URI that contains no "@" character, then the actual URI used in the SIP signaling SHOULD be automatically formed by the CPE by appending this parameter with an "@" character followed by the value of VoiceProfile.{i}.SIP.UserAgentDomain. If VoiceProfile.{i}.SIP.UserAgentDomain is an empty string, then the IP address of the CPE SHOULD be used for the domain.

-

1.0

SIPEventSubscribeNumberOfElements

unsignedInt

R

Indicates the number of EventSubscribe objects.

-

1.0

Event

string(:32)

R

SIP event name corresponding to the value given in VoiceProfile.{i}.SIP.EventSubscribe.{i}..

-

1.0

AuthUserName

string(:128)

W

Username used to authenticate the connection to the event notify server.

<Empty>

1.0

AuthPassword

string(:128)

W

Password used to authenticate the connection to the event notify server.

When read, this parameter returns an empty string, regardless of the actual value.

<Empty>

1.0

LineName

string(:32)

W

Used to identify the line when using MGCP signaling. If empty, the CPE SHOULD use the default names "aaln/1", etc.

<Empty>

1.0

H323ID

string(:32)

W

The H.323 ID assigned to the line.

<Empty>

1.0

EventNumberOfEntries

unsignedInt

R

Number of entries in VoiceProfile.{i}.Line.{i}.Ringer.Event.{i}..

-

1.0

DescriptionNumberOfEntries

unsignedInt

R

Number of entries in VoiceProfile.{i}.Line.{i}.Ringer.Description.{i}..

-

1.0

PatternNumberOfEntries

unsignedInt

R

Number of entries in VoiceProfile.{i}.Line.{i}.Ringer.Pattern.{i}..

-

1.0

Function

string(:64)

R

The event for which the ring pattern is to apply. Enumeration of:

• Default
• RingSplash The parameter MAY instead indicate a vendor-specific event name, which MUST use the format defined in [TR-106].

-

1.0

RingID

unsignedInt

W

The value of an instance of VoiceProfile.{i}.Line.{i}.Ringer.Description.{i}.EntryID for the ring to be associated with the given event. A value of zero indicates ringing is to be disabled for this event.

-

1.0

EntryID

unsignedInt(1:)

R

Unique identifier of this ring description. Assigned by the CPE upon creation of the entry.

-

1.0

RingEnable

boolean

W

Enables or disables the ring description entry. If a disabled ring description entry is referenced, the result is that no ring is played.

false

1.0

RingName

string(:64)

W

Name of the ring description. This parameter is required to be editable only if Capabilities.RingDescriptionsEditable is equal to true.

<Empty>

1.0

RingPattern

unsignedInt

W

The instance of VoiceProfile.{i}.Line.{i}.Ringer.Pattern.{i}.EntryID that begins the ring pattern for this ring description. If the ring is specified by a ring file instead of a ring pattern, this parameter MUST be set to zero. This parameter is applicable only if Capabilities.PatternBasedRingGeneration is equal to true. This parameter is required to be editable only if Capabilities.RingDescriptionsEditable is equal to true.

0

1.0

RingFile

string(:256)

W

This is the file name of a ring file that has been downloaded to the CPE. The download may have occurred via the TR-069 Download mechanism or by some other means. If the ring is specified by a ring pattern instead of a ring file, this parameter MUST be empty. This parameter is applicable only if Capabilities.FileBasedRingGeneration is equal to true. This parameter is required to be editable only Capabilities.RingDescriptionsEditable is equal to true.

<Empty>

1.0

EntryID

unsignedInt(1:)

W

Identifier of a ring-pattern entry. This parameter is required to be editable only if Capabilities.RingPatternEditable is equal to true. Note: when Capabilities.RingPatternEditable is true, this parameter is editable so that the NextEntryID values for each table entry can be pre-assigned for a series of associated table entries rather than requiring the ACS to set the value according to an ID assigned dynamically upon creation of each entry.

The Agent MUST choose an initial value that doesn't conflict with any existing entries.

-

1.0

RingerOn

boolean

W

If true, indicates the ringer is to be on for the specified period. false indicates the ringer is to be off for the specified period. This parameter is required to be editable only if Capabilities.RingPatternEditable is equal to true.

false

1.0

Duration

unsignedInt

W

The duration of this phase of the ring pattern, in milliseconds. A value of zero indicates an unlimited duration. This parameter is required to be editable only if Capabilities.RingPatternEditable is equal to true.

0

1.0

NextEntryID

unsignedInt

W

The value of EntryID for the next phase of the ring pattern, after the value specified by Duration of this phase has completed. A value of zero indicates that the ring pattern is to terminate after the current phase is completed. This parameter is required to be editable only if Capabilities.RingPatternEditable is equal to true.

0

1.0

CallerIDEnable

boolean

W

Enable or disable the transmission of caller ID information on outgoing calls.

-

1.0

CallerIDNameEnable

boolean

W

Enable or disable the transmission of caller ID name information on outgoing calls.

-

1.0

CallerIDName

string(:256)

W

String used to identify the caller.

-

1.0

CallWaitingEnable

boolean

W

Enable or disable call waiting in the endpoint. This parameter should not be present if the CPE does not support endpoint managed call waiting.

-

1.0

CallWaitingStatus

string

R

Status of endpoint managed call waiting, if supported. Enumeration of:

• Disabled
• Idle
• SecondaryRinging
• SecondaryConnecting
• SecondaryConnected This parameter should not be present if the CPE does not support endpoint managed call waiting.

-

1.0

MaxSessions

unsignedInt

W

Indicates the maximum number of simultaneous sessions that may be conferenced together by the endpoint. This value SHOULD be less than the value of Capabilities.MaxSessionsPerLine. This parameter should not be present if the CPE does not support endpoint managed conference calling.

-

1.0

ConferenceCallingStatus

string

R

Status of endpoint managed conference calling, if supported. Enumeration of:

• Disabled
• Idle
• SecondaryCalling
• SecondaryConnecting
• SecondaryConnected
• InConferenceCall This parameter should not be present if the CPE does not support endpoint managed conference calling.

-

1.0

ConferenceCallingSessionCount

unsignedInt(0,1,1:)

R

Number of active sessions on this line. This parameter should not be present if the CPE does not support endpoint managed conference calling.

-

1.0

CallForwardUnconditionalEnable

boolean

W

Enable or disable call forwarding by the endpoint. This parameter should not be present if the CPE does not support endpoint based call forwarding.

-

1.0

CallForwardUnconditionalNumber

string(:32)

W

Directory number to which all incoming calls to this line should be forwarded if CallForwardUnconditionalEnable is true. This parameter should not be present if the CPE does not support endpoint based call forwarding

-

1.0

CallForwardOnBusyEnable

boolean

W

Enable or disable call forwarding-on-busy by the endpoint. This parameter should not be present if the CPE does not support endpoint based call forwarding.

-

1.0

CallForwardOnBusyNumber

string(:32)

W

Directory number to which all incoming calls to this line should be forwarded if CallForwardOnBusyEnable is true and the line is busy. This parameter should not be present if the CPE does not support endpoint based call forwarding

-

1.0

CallForwardOnNoAnswerEnable

boolean

W

Enable or disable call forwarding-on-no-answer by the endpoint. This parameter should not be present if the CPE does not support endpoint based call forwarding.

-

1.0

CallForwardOnNoAnswerNumber

string(:32)

W

Directory number to which all incoming calls to this line should be forwarded if CallForwardOnNoAnswerEnable is true and there is no local answer. This parameter should not be present if the CPE does not support endpoint based call forwarding

-

1.0

CallForwardOnNoAnswerRingCount

unsignedInt

W

Number of rings before considering there to be no answer for call forwarding-on-no-answer. This parameter should not be present if the CPE does not support endpoint based call forwarding

-

1.0

CallTransferEnable

boolean

W

Enable or disable call transfer by the endpoint. This parameter should not be present if the CPE does not support endpoint based call transfer.

-

1.0

MWIEnable

boolean

W

Enable or disable Message Waiting Indication by the endpoint. This parameter should not be present if the CPE does not support MWI.

-

1.0

MessageWaiting

boolean

R

Indicates whether or not a message is currently waiting on this line as known by the CPE. This parameter should not be present if the CPE does not support MWI.

-

1.0

AnonymousCallBlockEnable

boolean

W

Enable or disable Anonymous Call Block capability in the endpoint. This parameter should not be present if the CPE does not support endpoint based Anonymous Call Block capability.

-

1.0

AnonymousCalEnable

boolean

W

Enable or disable Anonymous Call capability in the endpoint. This parameter should not be present if the CPE does not support endpoint based Anonymous Call capability.

-

1.0

DoNotDisturbEnable

boolean

W

Enable or disable Do Not Disturb capability in the endpoint. This parameter should not be present if the CPE does not support endpoint based Do Not Disturb capability.

-

1.0

CallReturnEnable

boolean

W

Enable or disable Call Return capability in the endpoint. This parameter should not be present if the CPE does not support endpoint based Call Return capability.

-

1.0

RepeatDialEnable

boolean

W

Enable or disable Repeat Dial capability in the endpoint. This parameter should not be present if the CPE does not support endpoint based Repeat Dial capability.

-

1.0

TransmitGain

int

W

Gain in 01. dB to apply to the transmitted voice signal prior to encoding. This gain is a modifier of the default transmit-gain, which is unspecified.

-

1.0

ReceiveGain

int

W

Gain in 0.1 dB to apply to the received voice signal after decoding. This gain is a modifier of the default receive-gain, which is unspecified.

-

1.0

EchoCancellationEnable

boolean

W

Enable or disable echo cancellation for this line.

-

1.0

EchoCancellationInUse

boolean

R

Indication of whether or not echo cancellation is currently in use for this line.

-

1.0

EchoCancellationTail

unsignedInt

R

Tail length in milliseconds of the echo canceller associated with this line (whether or not it is currently in use).

-

1.0

TransmitCodec

string(:64)

R

The codec currently in use for the outgoing voice stream.

Enumeration of:

• G.711MuLaw
• G.711ALaw
• G.726
• G.729
• G.729a
• G.729e
• G.728
• G.723.1
• G.722
• G.722.1
• G.722.2
• GSM-FR
• GSM-HR
• GSM-EFR
• iLBC

-

1.0

ReceiveCodec

string(:64)

R

The codec currently in use for the incoming voice stream.

Enumeration of:

• G.711MuLaw
• G.711ALaw
• G.726
• G.729
• G.729a
• G.729e
• G.728
• G.723.1
• G.722
• G.722.1
• G.722.2
• GSM-FR
• GSM-HR
• GSM-EFR
• iLBC

-

1.0

TransmitBitRate

unsignedInt

R

Codec bit rate in bits per second for the codec currently in use for the outgoing voice stream.

-

1.0

ReceiveBitRate

unsignedInt

R

Codec bit rate in bits per second for the codec currently in use for the incoming voice stream.

-

1.0

TransmitSilenceSuppression

boolean

R

Whether or not silence suppression is in use for the outgoing voice stream.

-

1.0

ReceiveSilenceSuppression

boolean

R

Whether or not silence suppression is in use for the incoming voice stream.

-

1.0

TransmitPacketizationPeriod

unsignedInt

R

Current outgoing packetization period in milliseconds.

-

1.0

EntryID

unsignedInt(1:)

R

Unique identifier for each entry in this table. The value MUST match that of the corresponding entry in Capabilities.Codecs. table.

-

1.0

Codec

string(:64)

R

Identifier of the codec type. The value MUST match that of the corresponding entry in Capabilities.Codecs..

-

1.0

BitRate

unsignedInt

R

Bit rate, in bits per second. The value MUST match that of the corresponding entry in Capabilities.Codecs.

-

1.0

PacketizationPeriod

string(:64)[]

W

Comma-separated list of strings (maximum number of characters per item 64). Each item is a supported packetization period, in milliseconds, or continuous ranges of packetization periods as defined in Capabilities.Codecs.{i}.PacketizationPeriod. The set of packetization periods may be restricted by modifying the value of this parameter to a more restricted set of values than is listed in Capabilities.Codecs.{i}.PacketizationPeriod. The CPE MUST ignore any values or portions of ranges outside of those specified in Capabilities.Codecs.{i}.PacketizationPeriod.

-

1.0

SilenceSuppression

boolean

W

Indicates support for silence suppression for this codec. If silence suppression is supported, it can be disabled for this codec/bit-rate by setting this parameter to false.

-

1.0

Enable

boolean

W

Enable or disable the use of this combination of codec parameters.

true

1.0

Priority

unsignedInt(1:)

W

Indicates the priority for this combination of codec parameters, where 1 is the highest priority. Where the priority differs between entries in this table, the CPE SHOULD use the highest priority (lowest numbered) entry among those supported by the remote endpoint and consistent with the available bandwidth. Where the priorities are equal among multiple entries, the CPE MAY apply a local criterion for choosing among them.

1

1.0

SessionStartTime

dateTime

R

The time that the session started, in UTC.

Active Notification requests for this parameter MAY be denied.

-

1.0

SessionDuration

unsignedInt

R

Duration time of the current session, in seconds.

Active Notification requests for this parameter MAY be denied.

-

1.0

FarEndIPAddress

string(:45)

R

[IPAddress] The IP address of far end VoIP device.

Active Notification requests for this parameter MAY be denied.

-

1.0

FarEndUDPPort

unsignedInt(0:65535)

R

The UDP port used for current RTP session in the far end device.

Active Notification requests for this parameter MAY be denied.

-

1.0

LocalUDPPort

unsignedInt(0:65535)

R

The local UDP port used for current RTP session.

Active Notification requests for this parameter MAY be denied.

-

1.0

ResetStatistics

boolean

W

When set to one, resets the statistics for this voice line. Always False when read.

-

1.0

PacketsSent

unsignedInt

R

Total number of RTP packets sent for this line.

Active Notification requests for this parameter MAY be denied.

-

1.0

PacketsReceived

unsignedInt

R

Total number of RTP packets received for this line.

Active Notification requests for this parameter MAY be denied.

-

1.0

BytesSent

unsignedInt

R

Total number of RTP payload bytes sent for this line.

Active Notification requests for this parameter MAY be denied.

-

1.0

BytesReceived

unsignedInt

R

Total number of RTP payload bytes received for this line.

Active Notification requests for this parameter MAY be denied.

-

1.0

PacketsLost

unsignedInt

R

Total number of RTP packets that have been lost for this line.

Active Notification requests for this parameter MAY be denied.

-

1.0

Overruns

unsignedInt

R

Total number of times the receive jitter buffer has overrun for this line.

Active Notification requests for this parameter MAY be denied.

-

1.0

Underruns

unsignedInt

R

Total number of times the receive jitter buffer has underrun for this line.

Active Notification requests for this parameter MAY be denied.

-

1.0

IncomingCallsReceived

unsignedInt

R

Total incoming calls received.

Active Notification requests for this parameter MAY be denied.

-

1.0

IncomingCallsAnswered

unsignedInt

R

Total incoming calls answered by the local user.

Active Notification requests for this parameter MAY be denied.

-

1.0

IncomingCallsConnected

unsignedInt

R

Total incoming calls that successfully completed call setup signaling.

Active Notification requests for this parameter MAY be denied.

-

1.0

IncomingCallsFailed

unsignedInt

R

Total incoming calls that failed to successfully complete call setup signaling.

Active Notification requests for this parameter MAY be denied.

-

1.0

OutgoingCallsAttempted

unsignedInt

R

Total outgoing calls attempted.

Active Notification requests for this parameter MAY be denied.

-

1.0

OutgoingCallsAnswered

unsignedInt

R

Total outgoing calls answered by the called party.

Active Notification requests for this parameter MAY be denied.

-

1.0

OutgoingCallsConnected

unsignedInt

R

Total outgoing calls that successfully completed call setup signaling.

Active Notification requests for this parameter MAY be denied.

-

1.0

OutgoingCallsFailed

unsignedInt

R

Total outgoing calls that failed to successfully complete call setup signaling.

Active Notification requests for this parameter MAY be denied.

-

1.0

CallsDropped

unsignedInt

R

Total calls that were successfully connected (incoming or outgoing), but dropped unexpectedly while in progress without explicit user termination.

Active Notification requests for this parameter MAY be denied.

-

1.0

TotalCallTime

unsignedInt

R

Cumulative call duration in seconds.

Active Notification requests for this parameter MAY be denied.

-

1.0

ServerDownTime

unsignedInt

R

The number of seconds the CPE is unable to maintain a connection to the server. SHOULD not include time in which overall network connectivity is unavailable. Applies only to SIP.

Active Notification requests for this parameter MAY be denied.

-

1.0

ReceivePacketLossRate

unsignedInt(0:100)

R

Current receive packet loss rate in percent, calculated as defined in [Section6.4/RFC3550]

Active Notification requests for this parameter MAY be denied.

-

1.0

FarEndPacketLossRate

unsignedInt(0:100)

R

Current far end receive packet lost rate in percent, calculated as defined in [Section6.4/RFC3550].

Active Notification requests for this parameter MAY be denied.

-

1.0

ReceiveInterarrivalJitter

unsignedInt

R

Current receive interarrival jitter in microseconds. Calculated from J(i) as defined in [Section6.4/RFC3550], with units converted to microseconds.

Active Notification requests for this parameter MAY be denied.

-

1.0

FarEndInterarrivalJitter

unsignedInt

R

Current Interarrival jitter in microseconds as reported from the far-end device via RTCP. Calculated from J(i) as defined in [Section64./RFC3550], with units converted to microseconds.

Active Notification requests for this parameter MAY be denied.

-

1.0

RoundTripDelay

unsignedInt

R

Current round trip delay in microseconds calculated as defined in [Section6.4/RFC3550].

Active Notification requests for this parameter MAY be denied.

-

1.0

AverageReceiveInterarrivalJitter

unsignedInt

R

Average receive interarrival jitter in microseconds since the beginning of the current call. Calculated as the average of D(i,j) as defined in [Section6.4/RFC3550], with units converted to microseconds.

Active Notification requests for this parameter MAY be denied.

-

1.0

AverageFarEndInterarrivalJitter

unsignedInt

R

Average far-end interarrival jitter in microseconds since the beginning of the current call. Calculated as the average of the interarrival jitter values reported by the far-end, with units converted to microseconds.

Active Notification requests for this parameter MAY be denied.

-

1.0

AverageRoundTripDelay

unsignedInt

R

Average round trip delay in microseconds since the beginning of the current call. Average of the RoundTripDelay statistic accumulated each time the delay is calculated.

Active Notification requests for this parameter MAY be denied.

-

1.0

PhyPort

string(:2)

R

The physical port number on the device.

-

1.0

InterfaceID

unsignedInt(1:)

R

The unique identifier of the physical port. This value MAY be used in VoiceProfile.{i}.Line.{i}.PhyReferenceList to indicate which physical ports are associated with a line.

-

1.0

Description

string(:32)

R

A description of the physical port.

-

1.0

TestState

string

W

Indicates the current test state. Enumeration of:

• None
• Requested
• Complete
• Error_TestNotSupported Value MAY be set to Requested to initiate a diagnostic test. When writing, the only allowed value is Requested. To ensure the use of the proper test parameters (the writable parameters in this object), the test parameters MUST be set either prior to or at the same time as (in the same SetParameterValues) setting the value Requested. When requested, the CPE SHOULD wait until after completion of the communication session with the ACS before starting the test. When the test initiated by the ACS is completed (successfully or not), the CPE MUST establish a new connection to the ACS to allow the ACS to view the results, indicating the Event code "8 DIAGNOSTICS COMPLETE" in the Inform message.

-

1.0

TestSelector

string(:64)

W

Indicates which test to perform. Enumeration of:

• PhoneConnectivityTest The phone connectivity test indicates that the CPE should determine if one or more phones associated with this physical port are properly connected. This test is appropriate only for CPE that connect to phones of any type. The parameter MAY instead indicate a vendor-specific test, which MUST use the format defined in [TR-106]. For example: "X_EXAMPLE-COM_MyTest"

-

1.0

PhoneConnectivity

boolean

R

Indicates whether or not at least one phone associated with this physical port is properly connected. This parameter is applicable only if PhoneConnectivityTest is supported.

-

1.0